Safely remove external USB drive crashes the system

[kereberos]

Hello everyone,
I'm using Debian Stretch 9.6 (64bit) with Mate.

Powering off an external USB drive after unmounting crashes the system (unresponsive mouse and keyboard), requiring an hard reboot.
I had the same result with a freshly downloaded Mate Live 9.6 image.
It doesn't matter which method I use, this happens with file manager, gnome-disk-utility and even typing 'udisksctl power-off -b /dev/sdX' on the command line.
I never had this problem on 9.5, or if I boot the old kernel.
After the reset, there are some messages about the root partition:

Recovering journal
Clearing orphaned inode

Is there anything I can do to fix this?

[bw123]

It's working the same on kde plasma, udisksctl power-off -b throws an error if device is mounted. After unmounting, powers off the device. Cool trick thanks.

I might try and see if it happens outside the Mate desktop, like from a tty. Mount it, unmount it, and pull the plug. What about syslog?

Is there anything on the device that your installation needs? like swap, configs, other mounts?

[kereberos]

The Hard Drive doesn't contain anything needed for the OS, just some data. Filesystem is NTFS. It's not always connected, so there's no fstab entry.
I also tried with a different FAT32 stick, I was able to unmount and power it off a couple of times, but eventually it happened with this one as well.
Syslog doesn't show anything particular, I guess it stops logging after the system hangs.
I was able to reproduce this on a TTY. It throws a lot of random codes listing my hardware, modules, codecs and so on, with a message that says "Fixing recursive fault but reboot is needed". The messages went very fast but I was able to get a couple of pics that I could post if needed.

[debiman]

It throws a lot of random codes listing my hardware, modules, codecs and so on, with a message that says "Fixing recursive fault but reboot is needed". The messages went very fast but I was able to get a couple of pics that I could post if needed.

well, these codes aren't random. please show us, commands & full output.
system messages should be in

Code: Select all

dmesg

also.

copy-pasting is preferable to a screenshot.

tell us something about your hardware.

[kereberos]

Sorry for the late reply.
My system is dual-booting from an SSD with Windows / Debian. There's another HDD where I symlinked some /home folders, formatted in NTFS, that automounts with a fstab entry.
NVIDIA GPU drivers are installed from stretch-backports/contrib (same for VirtualBox) and stretch-backports/non-free.
I also installed intel-microcode from stable/non-free.

Here is my Messages log:

Code: Select all

mtp-probe: bus: 1, device: 3 was not an MTP device
mtp-probe: checking bus 1, device 4: "/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3"
mtp-probe: bus: 1, device: 4 was not an MTP device
mtp-probe: checking bus 1, device 5: "/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.4"
mtp-probe: bus: 1, device: 5 was not an MTP device
kernel: [    0.000000] microcode: microcode updated early to revision 0x25, date = 2018-04-02
kernel: [    0.000000] Linux version 4.9.0-8-amd64 (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1) ) #1 SMP Debian 4.9.130-2 (2018-10-27)
kernel: [    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-8-amd64 root=UUID=1234ab56-c78d-9ee-1234-f5g6h789ij12 ro
kernel: [    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
kernel: [    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
kernel: [    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
kernel: [    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
kernel: [    0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
kernel: [    0.000000] e820: BIOS-provided physical RAM map:
kernel: [    0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
kernel: [    0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009efff] usable
kernel: [    0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000009ca57fff] usable
kernel: [    0.000000] BIOS-e820: [mem 0x000000009ca58000-0x000000009ca5efff] ACPI NVS
kernel: [    0.000000] BIOS-e820: [mem 0x000000009ca5f000-0x000000009cebffff] usable
kernel: [    0.000000] BIOS-e820: [mem 0x000000009cec0000-0x000000009d335fff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x000000009d336000-0x00000000bdb87fff] usable
kernel: [    0.000000] BIOS-e820: [mem 0x00000000bdb88000-0x00000000bdd71fff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x00000000bdd72000-0x00000000bdd8ffff] ACPI data
kernel: [    0.000000] BIOS-e820: [mem 0x00000000bdd90000-0x00000000be2b3fff] ACPI NVS
kernel: [    0.000000] BIOS-e820: [mem 0x00000000be2b4000-0x00000000bef4dfff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x00000000bef4e000-0x00000000beffefff] type 20
kernel: [    0.000000] BIOS-e820: [mem 0x00000000befff000-0x00000000beffffff] usable
kernel: [    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
kernel: [    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000023effffff] usable
kernel: [    0.000000] NX (Execute Disable) protection: active
kernel: [    0.000000] efi: EFI v2.31 by American Megatrends
kernel: [    0.000000] efi:  ESRT=0xbef4c818  ACPI 2.0=0xbdd78000  ACPI=0xbdd78000  SMBIOS=0xf04d0  MPS=0xfd5d0
kernel: [    0.000000] SMBIOS 2.8 present.
kernel: [    0.000000] e820: last_pfn = 0x23f000 max_arch_pfn = 0x400000000
kernel: [    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- WT 
kernel: [    0.000000] e820: last_pfn = 0xbf000 max_arch_pfn = 0x400000000
kernel: [    0.000000] found SMP MP-table at [mem 0x000fd8c0-0x000fd8cf] mapped at [ffff9d1f400fd8c0]
kernel: [    0.000000] esrt: Reserving ESRT space from 0x00000000bef4c818 to 0x00000000bef4c850.
kernel: [    0.000000] Using GB pages for direct mapping
kernel: [    0.000000] RAMDISK: [mem 0x359c9000-0x36cdbfff]
kernel: [    0.000000] ACPI: Early table checksum verification disabled
kernel: [    0.000000] ACPI: RSDP 0x00000000BDD78000 000024 (v02 ALASKA)
kernel: [    0.000000] ACPI: XSDT 0x00000000BDD78088 000084 (v01 ALASKA A M I    01072009 AMI  00010013)
kernel: [    0.000000] ACPI: FACP 0x00000000BDD87DF8 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
kernel: [    0.000000] ACPI: DSDT 0x00000000BDD781A0 00FC58 (v02 ALASKA A M I    00000011 INTL 20120711)
kernel: [    0.000000] ACPI: FACS 0x00000000BE2B3F80 000040
kernel: [    0.000000] ACPI: APIC 0x00000000BDD87F08 000072 (v03 ALASKA A M I    01072009 AMI  00010013)
kernel: [    0.000000] ACPI: FPDT 0x00000000BDD87F80 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
kernel: [    0.000000] ACPI: SSDT 0x00000000BDD87FC8 000C7D (v01 Ther_R Ther_Rvp 00001000 INTL 20120711)
kernel: [    0.000000] ACPI: SSDT 0x00000000BDD88C48 000539 (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
kernel: [    0.000000] ACPI: SSDT 0x00000000BDD89188 000B74 (v01 CpuRef CpuSsdt  00003000 INTL 20051117)
kernel: [    0.000000] ACPI: MCFG 0x00000000BDD89D00 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
kernel: [    0.000000] ACPI: HPET 0x00000000BDD89D40 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
kernel: [    0.000000] ACPI: SSDT 0x00000000BDD89D78 00036D (v01 SataRe SataTabl 00001000 INTL 20120711)
kernel: [    0.000000] ACPI: SSDT 0x00000000BDD8A0E8 005977 (v01 SaSsdt SaSsdt   00003000 INTL 20120711)
kernel: [    0.000000] ACPI: BGRT 0x00000000BDD8FB00 000038 (v01 ALASKA A M I    01072009 AMI  00010013)
kernel: [    0.000000] ACPI: UEFI 0x00000000BDD8FAB8 000042 (v01 ALASKA A M I    01072009      00000000)
kernel: [    0.000000] No NUMA configuration found
kernel: [    0.000000] Faking a node at [mem 0x0000000000000000-0x000000023effffff]
kernel: [    0.000000] NODE_DATA(0) allocated [mem 0x23eff9000-0x23effdfff]
kernel: [    0.000000] Zone ranges:
kernel: [    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
kernel: [    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
kernel: [    0.000000]   Normal   [mem 0x0000000100000000-0x000000023effffff]
kernel: [    0.000000]   Device   empty
kernel: [    0.000000] Movable zone start for each node
kernel: [    0.000000] Early memory node ranges
kernel: [    0.000000]   node   0: [mem 0x0000000000001000-0x0000000000057fff]
kernel: [    0.000000]   node   0: [mem 0x0000000000059000-0x000000000009efff]
kernel: [    0.000000]   node   0: [mem 0x0000000000100000-0x000000009ca57fff]
kernel: [    0.000000]   node   0: [mem 0x000000009ca5f000-0x000000009cebffff]
kernel: [    0.000000]   node   0: [mem 0x000000009d336000-0x00000000bdb87fff]
kernel: [    0.000000]   node   0: [mem 0x00000000befff000-0x00000000beffffff]
kernel: [    0.000000]   node   0: [mem 0x0000000100000000-0x000000023effffff]
kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000023effffff]
liblogging-stdlog:  [origin software="rsyslogd" swVersion="8.24.0" x-pid="626" x-info="http://www.rsyslog.com"] start
kernel: [    0.000000] ACPI: PM-Timer IO Port: 0x1808
kernel: [    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
kernel: [    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
kernel: [    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
kernel: [    0.000000] Using ACPI (MADT) for SMP configuration information
kernel: [    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
kernel: [    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
kernel: [    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0x00058000-0x00058fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0x9ca58000-0x9ca5efff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0x9cec0000-0x9d335fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xbdb88000-0xbdd71fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xbdd72000-0xbdd8ffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xbdd90000-0xbe2b3fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xbe2b4000-0xbef4dfff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xbef4e000-0xbeffefff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xbf000000-0xdfffffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
kernel: [    0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
kernel: [    0.000000] e820: [mem 0xbf000000-0xdfffffff] available for PCI devices
kernel: [    0.000000] Booting paravirtualized kernel on bare hardware
kernel: [    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
kernel: [    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
kernel: [    0.000000] percpu: Embedded 35 pages/cpu @ffff9d217ec00000 s105304 r8192 d29864 u524288
kernel: [    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 2049906
kernel: [    0.000000] Policy zone: Normal
kernel: [    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.9.0-8-amd64 root=UUID=1234ab56-c78d-9ee-1234-f5g6h789ij12 ro
kernel: [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
kernel: [    0.000000] Memory: 7866708K/8329892K available (6267K kernel code, 1159K rwdata, 2872K rodata, 1420K init, 688K bss, 463184K reserved, 0K cma-reserved)
kernel: [    0.000000] Kernel/User page tables isolation: enabled
kernel: [    0.000000] Hierarchical RCU implementation.
kernel: [    0.000000]    Build-time adjustment of leaf fanout to 64.
kernel: [    0.000000]    RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
kernel: [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
kernel: [    0.000000] NR_IRQS:33024 nr_irqs:456 16
kernel: [    0.000000] Console: colour dummy device 80x25
kernel: [    0.000000] console [tty0] enabled
kernel: [    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
kernel: [    0.000000] tsc: Fast TSC calibration using PIT
kernel: [    0.000000] tsc: Detected 3498.233 MHz processor
kernel: [    0.000017] Calibrating delay loop (skipped), value calculated using timer frequency.. 6996.46 BogoMIPS (lpj=13992932)
kernel: [    0.000021] pid_max: default: 32768 minimum: 301
kernel: [    0.000032] ACPI: Core revision 20160831
kernel: [    0.010761] ACPI: 6 ACPI AML tables successfully acquired and loaded
kernel: [    0.011005] Security Framework initialized
kernel: [    0.011008] Yama: disabled by default; enable with sysctl kernel.yama.*
kernel: [    0.011013] AppArmor: AppArmor disabled by boot time parameter
kernel: [    0.011284] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
kernel: [    0.012309] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
kernel: [    0.012768] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
kernel: [    0.012776] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
kernel: [    0.012973] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
kernel: [    0.012975] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
kernel: [    0.012979] mce: CPU supports 9 MCE banks
kernel: [    0.012987] CPU0: Thermal monitoring enabled (TM1)
kernel: [    0.012999] process: using mwait in idle threads
kernel: [    0.013003] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
kernel: [    0.013005] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
kernel: [    0.013007] Spectre V2 : Mitigation: Full generic retpoline
kernel: [    0.013009] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
kernel: [    0.013012] Spectre V2 : Spectre v2 mitigation: Enabling Indirect Branch Prediction Barrier
kernel: [    0.013015] Spectre V2 : Enabling Restricted Speculation for firmware calls
kernel: [    0.013017] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
kernel: [    0.013285] Freeing SMP alternatives memory: 24K
kernel: [   56.797763] ftrace: allocating 25291 entries in 99 pages
kernel: [   56.812596] smpboot: Max logical packages: 1
kernel: [   56.812664] x2apic: IRQ remapping doesn't support X2APIC mode
kernel: [   56.813012] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
kernel: [   56.852701] smpboot: CPU0: Intel(R) Core(TM) i5-4690K CPU @ 3.50GHz (family: 0x6, model: 0x3c, stepping: 0x3)
kernel: [   56.852707] Performance Events: PEBS fmt2+, Haswell events, 16-deep LBR, full-width counters, Intel PMU driver.
kernel: [   56.852746] ... version:                3
kernel: [   56.852748] ... bit width:              48
kernel: [   56.852750] ... generic registers:      8
kernel: [   56.852752] ... value mask:             0000ffffffffffff
kernel: [   56.852754] ... max period:             00007fffffffffff
kernel: [   56.852756] ... fixed-purpose events:   3
kernel: [   56.852758] ... event mask:             00000007000000ff
kernel: [   56.853147] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
kernel: [   56.853224] x86: Booting SMP configuration:
kernel: [   56.853227] .... node  #0, CPUs:      #1 #2 #3
kernel: [   56.862845] x86: Booted up 1 node, 4 CPUs
kernel: [   56.862851] smpboot: Total of 4 processors activated (27985.86 BogoMIPS)
kernel: [   56.865275] devtmpfs: initialized
kernel: [   56.865324] x86/mm: Memory block size: 128MB
kernel: [   56.866827] PM: Registering ACPI NVS region [mem 0x9ca58000-0x9ca5efff] (28672 bytes)
kernel: [   56.866831] PM: Registering ACPI NVS region [mem 0xbdd90000-0xbe2b3fff] (5390336 bytes)
kernel: [   56.866956] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
kernel: [   56.866965] futex hash table entries: 1024 (order: 4, 65536 bytes)
kernel: [   56.866995] pinctrl core: initialized pinctrl subsystem
kernel: [   56.867071] NET: Registered protocol family 16
kernel: [   56.885078] cpuidle: using governor ladder
kernel: [   56.905091] cpuidle: using governor menu
kernel: [   56.905106] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
kernel: [   56.905109] ACPI: bus type PCI registered
kernel: [   56.905112] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
kernel: [   56.905158] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
kernel: [   56.905163] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
kernel: [   56.905169] pmd_set_huge: Cannot satisfy [mem 0xe0000000-0xe0200000] with a huge-page mapping due to MTRR override.
kernel: [   56.905420] PCI: Using configuration type 1 for base access
kernel: [   56.905485] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
kernel: [   56.905517] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
kernel: [   56.921190] HugeTLB registered 1 GB page size, pre-allocated 0 pages
kernel: [   56.921193] HugeTLB registered 2 MB page size, pre-allocated 0 pages
kernel: [   56.921332] ACPI: Added _OSI(Module Device)
kernel: [   56.921335] ACPI: Added _OSI(Processor Device)
kernel: [   56.921337] ACPI: Added _OSI(3.0 _SCP Extensions)
kernel: [   56.921339] ACPI: Added _OSI(Processor Aggregator Device)
kernel: [   56.921628] ACPI: Executed 4 blocks of module-level executable AML code
kernel: [   56.926119] ACPI: Dynamic OEM Table Load:
kernel: [   56.926125] ACPI: SSDT 0xFFFF9D2174F03C00 0003D3 (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
kernel: [   56.926452] ACPI: Dynamic OEM Table Load:
kernel: [   56.926458] ACPI: SSDT 0xFFFF9D2174F21000 0005AA (v01 PmRef  ApIst    00003000 INTL 20051117)
kernel: [   56.926795] ACPI: Dynamic OEM Table Load:
kernel: [   56.926801] ACPI: SSDT 0xFFFF9D2174F3C000 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
kernel: [   56.927475] ACPI : EC: EC started
kernel: [   56.927478] ACPI : EC: interrupt blocked
kernel: [   56.927490] ACPI: \_SB_.PCI0.LPCB.EC0_: Used as first EC
kernel: [   56.927493] ACPI: \_SB_.PCI0.LPCB.EC0_: GPE=0x1e, EC_CMD/EC_SC=0x66, EC_DATA=0x62
kernel: [   56.927497] ACPI: \_SB_.PCI0.LPCB.EC0_: Used as boot DSDT EC to handle transactions
kernel: [   56.927500] ACPI: Interpreter enabled
kernel: [   56.927527] ACPI: (supports S0 S3 S4 S5)
kernel: [   56.927529] ACPI: Using IOAPIC for interrupt routing
kernel: [   56.927555] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
kernel: [   56.927945] ACPI: Power Resource [PG00] (on)
kernel: [   56.928166] ACPI: Power Resource [PG01] (on)
kernel: [   56.928379] ACPI: Power Resource [PG02] (on)
kernel: [   56.934247] ACPI: Power Resource [FN00] (off)
kernel: [   56.934302] ACPI: Power Resource [FN01] (off)
kernel: [   56.934357] ACPI: Power Resource [FN02] (off)
kernel: [   56.934411] ACPI: Power Resource [FN03] (off)
kernel: [   56.934464] ACPI: Power Resource [FN04] (off)
kernel: [   56.935289] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
kernel: [   56.935295] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
kernel: [   56.935470] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug PME]
kernel: [   56.935583] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
kernel: [   56.935586] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
kernel: [   56.936073] PCI host bridge to bus 0000:00
kernel: [   56.936077] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
kernel: [   56.936079] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
kernel: [   56.936082] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
kernel: [   56.936086] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
kernel: [   56.936089] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
kernel: [   56.936092] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
kernel: [   56.936096] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
kernel: [   56.936099] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfeafffff window]
kernel: [   56.936103] pci_bus 0000:00: root bus resource [bus 00-fe]
kernel: [   56.936266] pci 0000:00:01.0: System wakeup disabled by ACPI
kernel: [   56.936413] pci 0000:00:14.0: System wakeup disabled by ACPI
kernel: [   56.936688] pci 0000:00:19.0: System wakeup disabled by ACPI
kernel: [   56.936843] pci 0000:00:1a.0: System wakeup disabled by ACPI
kernel: [   56.936980] pci 0000:00:1b.0: System wakeup disabled by ACPI
kernel: [   56.937117] pci 0000:00:1c.0: System wakeup disabled by ACPI
kernel: [   56.937255] pci 0000:00:1c.3: System wakeup disabled by ACPI
kernel: [   56.937413] pci 0000:00:1d.0: System wakeup disabled by ACPI
kernel: [   56.937917] pci 0000:01:00.0: System wakeup disabled by ACPI
kernel: [   56.950916] pci 0000:00:01.0: PCI bridge to [bus 01]
kernel: [   56.950999] acpiphp: Slot [1] registered
kernel: [   56.951003] pci 0000:00:1c.0: PCI bridge to [bus 02]
kernel: [   56.951163] pci 0000:03:00.0: System wakeup disabled by ACPI
kernel: [   56.951188] pci 0000:00:1c.3: PCI bridge to [bus 03-04] (subtractive decode)
kernel: [   56.951291] pci 0000:03:00.0: PCI bridge to [bus 04] (subtractive decode)
kernel: [   56.951878] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
kernel: [   56.951916] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
kernel: [   56.951954] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
kernel: [   56.951991] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
kernel: [   56.952027] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
kernel: [   56.952064] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 *15)
kernel: [   56.952101] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 *14 15)
kernel: [   56.952137] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 *6 7 10 11 12 14 15)
kernel: [   56.952348] ACPI: Enabled 6 GPEs in block 00 to 3F
kernel: [   56.952371] ACPI : EC: interrupt unblocked
kernel: [   56.952376] ACPI : EC: event unblocked
kernel: [   56.952383] ACPI: \_SB_.PCI0.LPCB.EC0_: GPE=0x1e, EC_CMD/EC_SC=0x66, EC_DATA=0x62
kernel: [   56.952386] ACPI: \_SB_.PCI0.LPCB.EC0_: Used as boot DSDT EC to handle transactions and events
kernel: [   56.952443] vgaarb: setting as boot device: PCI:0000:01:00.0
kernel: [   56.952446] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
kernel: [   56.952449] vgaarb: loaded
kernel: [   56.952451] vgaarb: bridge control possible 0000:01:00.0
kernel: [   56.952475] Registered efivars operations
kernel: [   56.955166] PCI: Using ACPI for IRQ routing
kernel: [   56.960366] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
kernel: [   56.960372] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
kernel: [   56.962385] clocksource: Switched to clocksource hpet
kernel: [   56.966603] VFS: Disk quotas dquot_6.6.0
kernel: [   56.966619] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
kernel: [   56.966672] pnp: PnP ACPI init
kernel: [   56.966750] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
kernel: [   56.966822] system 00:01: [io  0x0800-0x087f] has been reserved
kernel: [   56.966869] system 00:03: [io  0x1854-0x1857] has been reserved
kernel: [   56.966949] system 00:04: [io  0x0290-0x029f] has been reserved
kernel: [   56.966952] system 00:04: [io  0x02a0-0x02af] has been reserved
kernel: [   56.966955] system 00:04: [io  0x0a00-0x0aff] has been reserved
kernel: [   56.966994] system 00:05: [io  0x04d0-0x04d1] has been reserved
kernel: [   56.967410] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
kernel: [   56.967414] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
kernel: [   56.967417] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
kernel: [   56.967419] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
kernel: [   56.967422] system 00:07: [mem 0xe0000000-0xefffffff] has been reserved
kernel: [   56.967425] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
kernel: [   56.967428] system 00:07: [mem 0xfed90000-0xfed93fff] has been reserved
kernel: [   56.967431] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved
kernel: [   56.967433] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
kernel: [   56.967436] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
kernel: [   56.967439] system 00:07: [mem 0xdffe0000-0xdffeffff] has been reserved
kernel: [   56.967442] system 00:07: [mem 0xdfff0000-0xdfffffff] has been reserved
kernel: [   56.967565] pnp: PnP ACPI: found 8 devices
kernel: [   56.973186] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
kernel: [   56.973216] pci 0000:00:01.0: PCI bridge to [bus 01]
kernel: [   56.973219] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
kernel: [   56.973223] pci 0000:00:01.0:   bridge window [mem 0xde000000-0xdf0fffff]
kernel: [   56.973226] pci 0000:00:01.0:   bridge window [mem 0xc0000000-0xd1ffffff 64bit pref]
kernel: [   56.973231] pci 0000:00:1c.0: PCI bridge to [bus 02]
kernel: [   56.973241] pci 0000:03:00.0: PCI bridge to [bus 04]
kernel: [   56.973258] pci 0000:00:1c.3: PCI bridge to [bus 03-04]
kernel: [   56.973371] NET: Registered protocol family 2
kernel: [   56.973477] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
kernel: [   56.973557] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
kernel: [   56.973664] TCP: Hash tables configured (established 65536 bind 65536)
kernel: [   56.973681] UDP hash table entries: 4096 (order: 5, 131072 bytes)
kernel: [   56.973700] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
kernel: [   56.973741] NET: Registered protocol family 1
kernel: [   57.022465] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
kernel: [   57.022504] Unpacking initramfs...
kernel: [   57.229315] Freeing initrd memory: 19532K
kernel: [   57.229330] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
kernel: [   57.229334] software IO TLB [mem 0xabbb0000-0xafbb0000] (64MB) mapped at [ffff9d1febbb0000-ffff9d1fefbaffff]
kernel: [   57.229576] audit: initializing netlink subsys (disabled)
kernel: [   57.229592] audit: type=2000 audit(1542583724.448:1): initialized
kernel: [   57.229851] workingset: timestamp_bits=40 max_order=21 bucket_order=0
kernel: [   57.229880] zbud: loaded
kernel: [   57.230404] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
kernel: [   57.230427] io scheduler noop registered
kernel: [   57.230429] io scheduler deadline registered
kernel: [   57.230437] io scheduler cfq registered (default)
kernel: [   57.230711] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
kernel: [   57.230717] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
kernel: [   57.230730] efifb: probing for efifb
kernel: [   57.230743] efifb: framebuffer at 0xd1000000, using 3072k, total 3072k
kernel: [   57.230745] efifb: mode is 1024x768x32, linelength=4096, pages=1
kernel: [   57.230747] efifb: scrolling: redraw
kernel: [   57.230750] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
kernel: [   57.231859] Console: switching to colour frame buffer device 128x48
kernel: [   57.232917] fb0: EFI VGA frame buffer device
kernel: [   57.233122] GHES: HEST is not enabled!
kernel: [   57.233164] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
kernel: [   57.253619] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
kernel: [   57.253999] Linux agpgart interface v0.103
kernel: [   57.254059] AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
kernel: [   57.254074] AMD IOMMUv2 functionality not available on this system
kernel: [   57.254308] i8042: PNP: No PS/2 controller found. Probing ports directly.
kernel: [   57.256688] serio: i8042 KBD port at 0x60,0x64 irq 1
kernel: [   57.256702] serio: i8042 AUX port at 0x60,0x64 irq 12
kernel: [   57.256825] mousedev: PS/2 mouse device common for all mice
kernel: [   57.256864] rtc_cmos 00:02: RTC can wake from S4
kernel: [   57.256991] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
kernel: [   57.257025] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
kernel: [   57.257048] intel_pstate: Intel P-state driver initializing
kernel: [   57.257358] ledtrig-cpu: registered to indicate activity on CPUs
kernel: [   57.259026] NET: Registered protocol family 10
kernel: [   57.259698] mip6: Mobile IPv6
kernel: [   57.259741] NET: Registered protocol family 17
kernel: [   57.259789] mpls_gso: MPLS GSO support
kernel: [   57.260360] microcode: sig=0x306c3, pf=0x2, revision=0x25
kernel: [   57.260601] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
kernel: [   57.261012] registered taskstats version 1
kernel: [   57.263028] zswap: loaded using pool lzo/zbud
kernel: [   57.265321] ima: No TPM chip found, activating TPM-bypass!
kernel: [   57.267272] ima: Allocated hash algorithm: sha256
kernel: [   57.270203] rtc_cmos 00:02: setting system clock to 2018-11-18 23:29:41 UTC (1542583781)
kernel: [   57.274592] Freeing unused kernel memory: 1420K
kernel: [   57.276355] Write protecting the kernel read-only data: 12288k
kernel: [   57.279146] Freeing unused kernel memory: 1908K
kernel: [   57.286696] Freeing unused kernel memory: 1224K
kernel: [   57.299894] x86/mm: Checked W+X mappings: passed, no W+X pages found.
kernel: [   57.320801] random: systemd-udevd: uninitialized urandom read (16 bytes read)
kernel: [   57.321571] random: systemd-udevd: uninitialized urandom read (16 bytes read)
kernel: [   57.321628] random: udevadm: uninitialized urandom read (16 bytes read)
kernel: [   57.345163] thermal LNXTHERM:00: registered as thermal_zone0
kernel: [   57.345714] ACPI: Thermal Zone [TZ00] (28 C)
kernel: [   57.346371] pps_core: LinuxPPS API ver. 1 registered
kernel: [   57.346467] thermal LNXTHERM:01: registered as thermal_zone1
kernel: [   57.346468] ACPI: Thermal Zone [TZ01] (30 C)
kernel: [   57.348009] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
kernel: [   57.348914] PTP clock support registered
kernel: [   57.349005] ACPI: bus type USB registered
kernel: [   57.349020] usbcore: registered new interface driver usbfs
kernel: [   57.349026] usbcore: registered new interface driver hub
kernel: [   57.349043] usbcore: registered new device driver usb
kernel: [   57.351747] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
kernel: [   57.352511] ehci-pci: EHCI PCI platform driver
kernel: [   57.352596] xhci_hcd 0000:00:14.0: xHCI Host Controller
kernel: [   57.352599] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
kernel: [   57.353662] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
kernel: [   57.353735] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
kernel: [   57.353736] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
kernel: [   57.353737] usb usb1: Product: xHCI Host Controller
kernel: [   57.353737] usb usb1: Manufacturer: Linux 4.9.0-8-amd64 xhci-hcd
kernel: [   57.353738] usb usb1: SerialNumber: 0000:00:14.0
kernel: [   57.353854] hub 1-0:1.0: USB hub found
kernel: [   57.353868] hub 1-0:1.0: 14 ports detected
kernel: [   57.354300] xhci_hcd 0000:00:14.0: xHCI Host Controller
kernel: [   57.354303] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
kernel: [   57.354332] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
kernel: [   57.354333] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
kernel: [   57.354334] usb usb2: Product: xHCI Host Controller
kernel: [   57.354335] usb usb2: Manufacturer: Linux 4.9.0-8-amd64 xhci-hcd
kernel: [   57.354335] usb usb2: SerialNumber: 0000:00:14.0
kernel: [   57.354441] hub 2-0:1.0: USB hub found
kernel: [   57.354452] hub 2-0:1.0: 6 ports detected
kernel: [   57.358306] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
kernel: [   57.358306] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
kernel: [   57.358437] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
kernel: [   57.369382] AVX2 version of gcm_enc/dec engaged.
kernel: [   57.369889] AES CTR mode by8 optimization enabled
kernel: [   57.370540] SCSI subsystem initialized
kernel: [   57.450398] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
kernel: [   57.542064] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 78:24:af:8c:13:97
kernel: [   57.542573] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
kernel: [   57.543103] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
kernel: [   57.543766] i801_smbus 0000:00:1f.3: SPD Write Disable is set
kernel: [   57.544119] e1000e 0000:00:19.0 eno1: renamed from eth0
kernel: [   57.544782] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
kernel: [   57.545908] ehci-pci 0000:00:1a.0: EHCI Host Controller
kernel: [   57.546428] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
kernel: [   57.546944] ehci-pci 0000:00:1a.0: debug port 2
kernel: [   57.551349] ehci-pci 0000:00:1a.0: irq 16, io mem 0xdf137000
kernel: [   57.566388] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
kernel: [   57.566861] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
kernel: [   57.567305] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
kernel: [   57.567749] usb usb3: Product: EHCI Host Controller
kernel: [   57.568184] usb usb3: Manufacturer: Linux 4.9.0-8-amd64 ehci_hcd
kernel: [   57.568594] usb usb3: SerialNumber: 0000:00:1a.0
kernel: [   57.569147] hub 3-0:1.0: USB hub found
kernel: [   57.569559] hub 3-0:1.0: 2 ports detected
kernel: [   57.570108] ehci-pci 0000:00:1d.0: EHCI Host Controller
kernel: [   57.570559] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
kernel: [   57.570984] ehci-pci 0000:00:1d.0: debug port 2
kernel: [   57.575300] ehci-pci 0000:00:1d.0: irq 23, io mem 0xdf136000
kernel: [   57.686382] usb 1-3: new high-speed USB device number 2 using xhci_hcd
kernel: [   57.702388] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
kernel: [   57.703178] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
kernel: [   57.703915] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
kernel: [   57.704653] usb usb4: Product: EHCI Host Controller
kernel: [   57.705388] usb usb4: Manufacturer: Linux 4.9.0-8-amd64 ehci_hcd
kernel: [   57.706123] usb usb4: SerialNumber: 0000:00:1d.0
kernel: [   57.707080] hub 4-0:1.0: USB hub found
kernel: [   57.707825] hub 4-0:1.0: 2 ports detected
kernel: [   57.708911] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x7 impl SATA mode
kernel: [   57.709357] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part ems apst
kernel: [   57.730930] scsi host0: ahci
kernel: [   57.731606] scsi host1: ahci
kernel: [   57.732170] scsi host2: ahci
kernel: [   57.732707] scsi host3: ahci
kernel: [   57.733199] scsi host4: ahci
kernel: [   57.733681] scsi host5: ahci
kernel: [   57.734091] ata1: SATA max UDMA/133 abar m2048@0xdf135000 port 0xdf135100 irq 27
kernel: [   57.734497] ata2: SATA max UDMA/133 abar m2048@0xdf135000 port 0xdf135180 irq 27
kernel: [   57.734889] ata3: SATA max UDMA/133 abar m2048@0xdf135000 port 0xdf135200 irq 27
kernel: [   57.735277] ata4: DUMMY
kernel: [   57.735650] ata5: DUMMY
kernel: [   57.736009] ata6: DUMMY
kernel: [   57.844098] usb 1-3: New USB device found, idVendor=2109, idProduct=2812
kernel: [   57.844758] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
kernel: [   57.845404] usb 1-3: Product: USB2.0 Hub             
kernel: [   57.846043] usb 1-3: Manufacturer: VIA Labs, Inc.         
kernel: [   57.847397] hub 1-3:1.0: USB hub found
kernel: [   57.848240] hub 1-3:1.0: 4 ports detected
kernel: [   57.894358] usb 3-1: new high-speed USB device number 2 using ehci-pci
kernel: [   57.962488] usb 2-3: new SuperSpeed USB device number 2 using xhci_hcd
kernel: [   57.984221] usb 2-3: New USB device found, idVendor=2109, idProduct=0812
kernel: [   57.984600] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
kernel: [   57.984966] usb 2-3: Product: USB3.0 Hub             
kernel: [   57.985329] usb 2-3: Manufacturer: VIA Labs, Inc.         
kernel: [   57.987073] hub 2-3:1.0: USB hub found
kernel: [   57.988118] hub 2-3:1.0: 4 ports detected
kernel: [   58.034342] usb 4-1: new high-speed USB device number 2 using ehci-pci
kernel: [   58.042782] usb 3-1: New USB device found, idVendor=8087, idProduct=8009
kernel: [   58.043410] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
kernel: [   58.044272] hub 3-1:1.0: USB hub found
kernel: [   58.044962] hub 3-1:1.0: 6 ports detected
kernel: [   58.049220] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
kernel: [   58.049605] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
kernel: [   58.049981] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
kernel: [   58.050437] ata1.00: supports DRM functions and may not be fully accessible
kernel: [   58.051039] ata2.00: ATA-9: WDC WD10EZEX-00BN5A0, 01.01A01, max UDMA/133
kernel: [   58.051386] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
kernel: [   58.052275] ata3.00: ATAPI: TSSTcorp CDDVDW SH-224DB, SB01, max UDMA/100
kernel: [   58.052741] ata2.00: configured for UDMA/133
kernel: [   58.053749] ata3.00: configured for UDMA/100
kernel: [   58.058083] ata1.00: ATA-9: Crucial_CT128MX100SSD1, MU03, max UDMA/133
kernel: [   58.058450] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
kernel: [   58.063228] ata1.00: supports DRM functions and may not be fully accessible
kernel: [   58.074885] ata1.00: configured for UDMA/133
kernel: [   58.075452] scsi 0:0:0:0: Direct-Access     ATA      Crucial_CT128MX1 MU03 PQ: 0 ANSI: 5
kernel: [   58.102346] usb 1-13: new full-speed USB device number 3 using xhci_hcd
kernel: [   58.114669] scsi 1:0:0:0: Direct-Access     ATA      WDC WD10EZEX-00B 1A01 PQ: 0 ANSI: 5
kernel: [   58.148836] scsi 2:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-224DB  SB01 PQ: 0 ANSI: 5
kernel: [   58.170360] ata1.00: Enabling discard_zeroes_data
kernel: [   58.171190] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
kernel: [   58.171225] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
kernel: [   58.171228] sd 1:0:0:0: [sdb] 4096-byte physical blocks
kernel: [   58.171393] sd 1:0:0:0: [sdb] Write Protect is off
kernel: [   58.171476] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel: [   58.175119] sd 0:0:0:0: [sda] 4096-byte physical blocks
kernel: [   58.175715] sd 0:0:0:0: [sda] Write Protect is off
kernel: [   58.176291] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
kernel: [   58.177035] ata1.00: Enabling discard_zeroes_data
kernel: [   58.178584]  sda: sda1 sda2 sda3 sda4 sda5
kernel: [   58.179446] ata1.00: Enabling discard_zeroes_data
kernel: [   58.180077] sd 0:0:0:0: [sda] Attached SCSI disk
kernel: [   58.187086] usb 4-1: New USB device found, idVendor=8087, idProduct=8001
kernel: [   58.187662] usb 4-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
kernel: [   58.188491] hub 4-1:1.0: USB hub found
kernel: [   58.189209] hub 4-1:1.0: 8 ports detected
kernel: [   58.189441] sr 2:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
kernel: [   58.189442] cdrom: Uniform CD-ROM driver Revision: 3.20
kernel: [   58.196995] random: fast init done
kernel: [   58.235616]  sdb: sdb1 sdb2
kernel: [   58.236519] sd 1:0:0:0: [sdb] Attached SCSI disk
kernel: [   58.243383] usb 1-13: New USB device found, idVendor=22d4, idProduct=1308
kernel: [   58.243849] usb 1-13: New USB device strings: Mfr=1, Product=2, SerialNumber=3
kernel: [   58.244317] usb 1-13: Product: Mionix Avior 7000
kernel: [   58.244794] usb 1-13: Manufacturer: Laview Technology
kernel: [   58.245243] usb 1-13: SerialNumber: STM32
kernel: [   58.246297] tsc: Refined TSC clocksource calibration: 3497.972 MHz
kernel: [   58.246749] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x326bd592a83, max_idle_ns: 440795311901 ns
kernel: [   58.247318] hidraw: raw HID events driver (C) Jiri Kosina
kernel: [   58.249163] usbcore: registered new interface driver usbhid
kernel: [   58.249649] usbhid: USB HID core driver
kernel: [   58.250459] input: Laview Technology Mionix Avior 7000 as /devices/pci0000:00/0000:00:14.0/usb1/1-13/1-13:1.0/0003:22D4:1308.0001/input/input3
kernel: [   58.251537] hid-generic 0003:22D4:1308.0001: input,hidraw0: USB HID v1.00 Mouse [Laview Technology Mionix Avior 7000] on usb-0000:00:14.0-13/input0
kernel: [   58.254219] input: Laview Technology Mionix Avior 7000 as /devices/pci0000:00/0000:00:14.0/usb1/1-13/1-13:1.1/0003:22D4:1308.0002/input/input4
kernel: [   58.314431] hid-generic 0003:22D4:1308.0002: input,hiddev0,hidraw1: USB HID v1.00 Keyboard [Laview Technology Mionix Avior 7000] on usb-0000:00:14.0-13/input1
kernel: [   58.334322] usb 1-3.3: new full-speed USB device number 4 using xhci_hcd
kernel: [   58.447769] usb 1-3.3: New USB device found, idVendor=0d8c, idProduct=0105
kernel: [   58.450348] usb 1-3.3: New USB device strings: Mfr=3, Product=1, SerialNumber=0
kernel: [   58.452851] usb 1-3.3: Product: USB Multimedia Audio Device
kernel: [   58.455364] usb 1-3.3: Manufacturer: C-Media Electronics Inc.
kernel: [   58.460108] input: C-Media Electronics Inc. USB Multimedia Audio Device as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.3/0003:0D8C:0105.0003/input/input5
kernel: [   58.522587] hid-generic 0003:0D8C:0105.0003: input,hidraw2: USB HID v1.00 Device [C-Media Electronics Inc. USB Multimedia Audio Device] on usb-0000:00:14.0-3.3/input3
kernel: [   58.560702] PM: Starting manual resume from disk
kernel: [   58.622289] usb 1-3.4: new full-speed USB device number 5 using xhci_hcd
kernel: [   58.738998] usb 1-3.4: New USB device found, idVendor=2516, idProduct=0018
kernel: [   58.739625] usb 1-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
kernel: [   58.740246] usb 1-3.4: Product: MECH
kernel: [   58.740859] usb 1-3.4: Manufacturer: CM Storm
kernel: [   58.742274] input: CM Storm MECH as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.4/1-3.4:1.0/0003:2516:0018.0004/input/input6
kernel: [   58.802402] hid-generic 0003:2516:0018.0004: input,hidraw3: USB HID v1.11 Keyboard [CM Storm MECH] on usb-0000:00:14.0-3.4/input0
kernel: [   58.804273] hid-generic 0003:2516:0018.0005: hiddev0,hidraw4: USB HID v1.11 Device [CM Storm MECH] on usb-0000:00:14.0-3.4/input1
kernel: [   58.806733] input: CM Storm MECH as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.4/1-3.4:1.2/0003:2516:0018.0006/input/input7
kernel: [   58.866366] hid-generic 0003:2516:0018.0006: input,hidraw5: USB HID v1.11 Mouse [CM Storm MECH] on usb-0000:00:14.0-3.4/input2
kernel: [   58.881388] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
kernel: [   58.946460] ip_tables: (C) 2000-2006 Netfilter Core Team
kernel: [   59.017611] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
kernel: [   59.021916] EXT4-fs (sda4): re-mounted. Opts: errors=remount-ro
kernel: [   59.029875] ipmi message handler version 39.2
kernel: [   59.033568] ip6_tables: (C) 2000-2006 Netfilter Core Team
kernel: [   59.086565] nvidia: loading out-of-tree module taints kernel.
kernel: [   59.087055] nvidia: module license 'NVIDIA' taints kernel.
kernel: [   59.087499] Disabling lock debugging due to kernel taint
kernel: [   59.096987] nvidia-nvlink: Nvlink Core is being initialized, major device number 246
kernel: [   59.097687] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
kernel: [   59.098187] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  390.87  Tue Aug 21 12:33:05 PDT 2018 (using threaded interrupts)
kernel: [   59.112012] nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms  390.87  Tue Aug 21 16:16:14 PDT 2018
kernel: [   59.119750] [drm] Initialized
kernel: [   59.124357] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input8
kernel: [   59.124854] ACPI: Power Button [PWRB]
kernel: [   59.125486] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input9
kernel: [   59.125989] ACPI: Power Button [PWRF]
kernel: [   59.133594] wmi: Mapper loaded
kernel: [   59.136972] [drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
kernel: [   59.174514] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
kernel: [   59.175922] EFI Variables Facility v0.08 2004-May-17
kernel: [   59.176528] sd 0:0:0:0: Attached scsi generic sg0 type 0
kernel: [   59.180077] sd 1:0:0:0: Attached scsi generic sg1 type 0
kernel: [   59.180667] pstore: using zlib compression
kernel: [   59.181150] pstore: Registered efi as persistent store backend
kernel: [   59.181741] input: PC Speaker as /devices/platform/pcspkr/input/input10
kernel: [   59.181916] sr 2:0:0:0: Attached scsi generic sg2 type 5
kernel: [   59.187539] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)
kernel: [   59.188185] snd_hda_intel 0000:01:00.1: Disabling MSI
kernel: [   59.188678] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
kernel: [   59.191563] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer
kernel: [   59.192061] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
kernel: [   59.192558] RAPL PMU: hw unit of domain package 2^-14 Joules
kernel: [   59.193045] RAPL PMU: hw unit of domain dram 2^-14 Joules
kernel: [   59.193524] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
kernel: [   59.204217] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC892: line_outs=3 (0x14/0x15/0x16/0x0/0x0) type:line
kernel: [   59.204730] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
kernel: [   59.205231] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
kernel: [   59.205730] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
kernel: [   59.206231] snd_hda_codec_realtek hdaudioC0D0:    dig-out=0x11/0x1e
kernel: [   59.206722] snd_hda_codec_realtek hdaudioC0D0:    inputs:
kernel: [   59.208487] snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x19
kernel: [   59.208977] snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x18
kernel: [   59.209639] snd_hda_codec_realtek hdaudioC0D0:      Line=0x1a
kernel: [   59.219582] usbcore: registered new interface driver snd-usb-audio
kernel: [   59.226830] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
kernel: [   59.227899] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
kernel: [   59.229852] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
kernel: [   59.231225] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
kernel: [   59.231749] iTCO_vendor_support: vendor-support=0
kernel: [   59.232571] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
kernel: [   59.232697] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
kernel: [   59.232744] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
kernel: [   59.232791] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
kernel: [   59.234848] iTCO_wdt: Found a 9 Series TCO device (Version=2, TCOBASE=0x1860)
kernel: [   59.236073] asus_wmi: ASUS WMI generic driver loaded
kernel: [   59.236940] intel_rapl: Found RAPL domain package
kernel: [   59.237391] intel_rapl: Found RAPL domain core
kernel: [   59.237548] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
kernel: [   59.238392] intel_rapl: Found RAPL domain dram
kernel: [   59.238942] asus_wmi: Initialization: 0x0
kernel: [   59.239397] asus_wmi: BIOS WMI version: 0.9
kernel: [   59.239847] asus_wmi: SFUN value: 0x0
kernel: [   59.240501] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input18
kernel: [   59.241036] asus_wmi: Number of fans: 1
kernel: [   59.271316] clocksource: Switched to clocksource tsc
kernel: [   59.273966] fuse init (API version 7.26)
kernel: [   59.279106] Adding 3906556k swap on /dev/sda5.  Priority:-1 extents:1 across:3906556k SSFS
kernel: [   59.587006] random: crng init done
kernel: [   59.587698] random: 7 urandom warning(s) missed due to ratelimiting
NetworkManager[636]: <info>  [1542580184.0460] NetworkManager (version 1.6.2) is starting...
NetworkManager[636]: <info>  [1542580184.0463] Read config: /etc/NetworkManager/NetworkManager.conf
NetworkManager[636]: <info>  [1542580184.0489] manager[0x563b733df040]: monitoring kernel firmware directory '/lib/firmware'.
NetworkManager[636]: <info>  [1542580184.0489] monitoring ifupdown state file '/run/network/ifstate'.
NetworkManager[636]: <info>  [1542580184.0503] dns-mgr[0x563b733d4180]: init: dns=default, rc-manager=resolvconf
NetworkManager[636]: <info>  [1542580184.0512] manager[0x563b733df040]: WiFi hardware radio set enabled
NetworkManager[636]: <info>  [1542580184.0512] manager[0x563b733df040]: WWAN hardware radio set enabled
NetworkManager[636]: <info>  [1542580184.0853] init!
NetworkManager[636]: <info>  [1542580184.0855] management mode: unmanaged
NetworkManager[636]: <info>  [1542580184.0856] devices added (path: /sys/devices/pci0000:00/0000:00:19.0/net/eno1, iface: eno1)
NetworkManager[636]: <info>  [1542580184.0856] device added (path: /sys/devices/pci0000:00/0000:00:19.0/net/eno1, iface: eno1): no ifupdown configuration found.
NetworkManager[636]: <info>  [1542580184.0857] devices added (path: /sys/devices/virtual/net/lo, iface: lo)
NetworkManager[636]: <info>  [1542580184.0857] device added (path: /sys/devices/virtual/net/lo, iface: lo): no ifupdown configuration found.
NetworkManager[636]: <info>  [1542580184.0857] end _init.
NetworkManager[636]: <info>  [1542580184.0857] settings: loaded plugin ifupdown: (C) 2008 Canonical Ltd.  To report bugs please use the NetworkManager mailing list. (/usr/lib/x86_64-linux-gnu/NetworkManager/libnm-settings-plugin-ifupdown.so)
NetworkManager[636]: <info>  [1542580184.0857] settings: loaded plugin keyfile: (c) 2007 - 2016 Red Hat, Inc.  To report bugs please use the NetworkManager mailing list.
NetworkManager[636]: <info>  [1542580184.0857] (1933586560) ... get_connections.
NetworkManager[636]: <info>  [1542580184.0857] (1933586560) ... get_connections (managed=false): return empty list.
NetworkManager[636]: <info>  [1542580184.0919] keyfile: new connection /etc/NetworkManager/system-connections/Connection (a12345b6-34cd-5678-90e1-2345f67890g1,"Connection")
NetworkManager[636]: <info>  [1542580184.0933] get unmanaged devices count: 0
kernel: [   59.882339] vboxdrv: TSC mode is Invariant, tentative frequency 3497971584 Hz
kernel: [   59.886147] VBoxNetFlt: Successfully started.
kernel: [   59.890028] VBoxNetAdp: Successfully started.
kernel: [   59.893962] VBoxPciLinuxInit
kernel: [   59.895625] vboxpci: IOMMU not found (not registered)
kernel: [   60.048966] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input19
kernel: [   60.049010] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input20
kernel: [   60.049047] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input21
kernel: [   60.049084] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input22
NetworkManager[636]: <info>  [1542580184.2936] settings: hostname: using hostnamed
NetworkManager[636]: <info>  [1542580184.2936] settings: hostname changed from (none) to "MYPC"
NetworkManager[636]: <info>  [1542580184.2947] dhcp-init: Using DHCP client 'dhclient'
NetworkManager[636]: <info>  [1542580184.2947] manager: WiFi enabled by radio killswitch; enabled by state file
NetworkManager[636]: <info>  [1542580184.2947] manager: WWAN enabled by radio killswitch; enabled by state file
NetworkManager[636]: <info>  [1542580184.2947] manager: Networking is enabled by state file
NetworkManager[636]: <info>  [1542580184.2950] Loaded device plugin: NMBondDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2950] Loaded device plugin: NMBridgeDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2950] Loaded device plugin: NMEthernetDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2950] Loaded device plugin: NMInfinibandDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2950] Loaded device plugin: NMIPTunnelDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2951] Loaded device plugin: NMMacsecDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2951] Loaded device plugin: NMMacvlanDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2951] Loaded device plugin: NMTunDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2951] Loaded device plugin: NMVethDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2951] Loaded device plugin: NMVlanDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2951] Loaded device plugin: NMVxlanDeviceFactory (internal)
NetworkManager[636]: <info>  [1542580184.2966] Loaded device plugin: NMTeamFactory (/usr/lib/x86_64-linux-gnu/NetworkManager/libnm-device-plugin-team.so)
NetworkManager[636]: <info>  [1542580184.2974] Loaded device plugin: NMWifiFactory (/usr/lib/x86_64-linux-gnu/NetworkManager/libnm-device-plugin-wifi.so)
NetworkManager[636]: <info>  [1542580184.3015] Loaded device plugin: NMBluezManager (/usr/lib/x86_64-linux-gnu/NetworkManager/libnm-device-plugin-bluetooth.so)
NetworkManager[636]: <info>  [1542580184.3020] Loaded device plugin: NMWwanFactory (/usr/lib/x86_64-linux-gnu/NetworkManager/libnm-device-plugin-wwan.so)
NetworkManager[636]: <info>  [1542580184.3026] Loaded device plugin: NMAtmManager (/usr/lib/x86_64-linux-gnu/NetworkManager/libnm-device-plugin-adsl.so)
NetworkManager[636]: <info>  [1542580184.3036] device (lo): link connected
NetworkManager[636]: <info>  [1542580184.3041] manager: (lo): new Generic device (/org/freedesktop/NetworkManager/Devices/1)
NetworkManager[636]: <info>  [1542580184.3047] manager: (eno1): new Ethernet device (/org/freedesktop/NetworkManager/Devices/2)
NetworkManager[636]: <info>  [1542580184.3054] device (eno1): state change: unmanaged -> unavailable (reason 'managed') [10 20 2]
kernel: [   60.075608] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
kernel: [   60.298287] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
org.a11y.atspi.Registry[790]: SpiRegistry daemon is running with well-known name - org.a11y.atspi.Registry
kernel: [   61.817944] e1000e: eno1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
kernel: [   61.817948] e1000e 0000:00:19.0 eno1: 10/100 speed: disabling TSO
kernel: [   61.817977] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
NetworkManager[636]: <info>  [1542580186.0483] device (eno1): link connected
NetworkManager[636]: <info>  [1542580186.0485] device (eno1): state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40]
NetworkManager[636]: <info>  [1542580186.0489] policy: auto-activating connection 'Connection'
NetworkManager[636]: <info>  [1542580186.0495] device (eno1): Activation: starting connection 'Connection' (a12345b6-34cd-5678-90e1-2345f67890g1)
NetworkManager[636]: <info>  [1542580186.0496] device (eno1): state change: disconnected -> prepare (reason 'none') [30 40 0]
NetworkManager[636]: <info>  [1542580186.0497] manager: NetworkManager state is now CONNECTING
NetworkManager[636]: <info>  [1542580186.0499] device (eno1): state change: prepare -> config (reason 'none') [40 50 0]
NetworkManager[636]: <info>  [1542580186.0501] device (eno1): state change: config -> ip-config (reason 'none') [50 70 0]
NetworkManager[636]: <info>  [1542580186.0506] dhcp4 (eno1): activation: beginning transaction (timeout in 45 seconds)
NetworkManager[636]: <info>  [1542580186.0605] dhcp4 (eno1): dhclient started with pid 807
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1):   address 192.168.0.2
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1):   plen 24 (255.255.255.0)
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1):   gateway 192.168.0.1
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1):   server identifier 192.168.0.1
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1):   lease time 86400
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1):   nameserver '8.8.8.8'
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1):   nameserver '1.1.1.1'
NetworkManager[636]: <info>  [1542580186.0960] dhcp4 (eno1): state changed unknown -> bound
NetworkManager[636]: <info>  [1542580186.0965] device (eno1): state change: ip-config -> ip-check (reason 'none') [70 80 0]
NetworkManager[636]: <info>  [1542580186.0968] device (eno1): state change: ip-check -> secondaries (reason 'none') [80 90 0]
NetworkManager[636]: <info>  [1542580186.0970] device (eno1): state change: secondaries -> activated (reason 'none') [90 100 0]
NetworkManager[636]: <info>  [1542580186.0971] manager: NetworkManager state is now CONNECTED_LOCAL
NetworkManager[636]: <info>  [1542580186.1131] manager: NetworkManager state is now CONNECTED_GLOBAL
NetworkManager[636]: <info>  [1542580186.1131] policy: set 'Connection' (eno1) as default for IPv4 routing and DNS
NetworkManager[636]: <info>  [1542580186.1135] device (eno1): Activation: successful, device activated.
NetworkManager[636]: <info>  [1542580191.0116] manager: startup complete
org.a11y.atspi.Registry[925]: SpiRegistry daemon is running with well-known name - org.a11y.atspi.Registry
notification-ar[975]: Negative content width -2 (allocation 1, extents 1x2) while allocating gadget (node box, owner GtkBox)
notification-ar[975]: Negative content height -1 (allocation 1, extents 1x1) while allocating gadget (node box, owner GtkBox)

On TTY, I unmounted the Hard Drive with 'sudo udisksctl unmount -b /dev/sdX1', and then powered it off with 'sudo udisksctl power-off -b /dev/sdX'. The second command makes the system crash.
I didn't find anything of this on the log files, so I took two pics:

https://imgur.com/7sW43oS
https://imgur.com/FqN7jSW

As you can see on the messages log, my boot is sometimes very slow (it takes more than one minute), and this happens on Windows as well.
systemd-analyze and systemd-analyze blame are ok: they always report around 20 sec boot, which is my normal boot time when I don't have any problem.
Fastboot is disabled on BIOS, while SecureBoot is enabled, but modified to boot Other OS.

[debiman]

maybe it has something to do with the ntfs usb drive?
is it connected through an external usb hub?
have you tried without the hub, or maybe even remove the usb drive from its enclosure & use it as an internal drive (this probably won't work with a laptop)?

whatdoes udisksctl power-off do?
what if you don't power the drive down?

also, isn't the point of udisks that you don't need superuser privileges to mount/unmount drives?

[kereberos]

maybe it has something to do with the ntfs usb drive?
is it connected through an external usb hub?
have you tried without the hub, or maybe even remove the usb drive from its enclosure & use it as an internal drive (this probably won't work with a laptop)?

I tried plugging it in all the USB ports of the motherboard, even the front ones, but it doesn't change anything.
It's a portable drive, so I can't remove the enclosure.
I tried again reverting the kernel to the previous ones, 4.9.110-3+deb9u6 and 4.9.110-3+deb9u2, and it still doesn't crash.

whatdoes udisksctl power-off do?
what if you don't power the drive down?

'udisksctl power-off' turns off the USB drive light and makes it stop spinning, but this happens even if I use any kind of eject/safe remove from the file manager, or gnome-disk-utility as well. If I just unmount it without powering it off, there's no crash.

also, isn't the point of udisks that you don't need superuser privileges to mount/unmount drives?

Actually, I needed sudo only on the TTY (I don't know why, I logged in with the same user). If I use the command while being logged in on Mate, there's no need for it, but the system crashes anyway.


I guess I should just revert to the old kernel and re-check this when a new one comes out.

[debiman]

if the drive is unmounted it should power down anyhow after some time.
so i wonder what would happen if you just don't "udisksctl power-off".

will it
- power down after some time (can be a while, maybe 30min. of course adjustable with hdparm)
- will your system crash when the drive powers down automagically

another troubleshooting test: what if you issue that command on some other drive. maybe one that doesn't even have power-down capabilities (a regular usb stick).
or what if you issue a power-down with hdparm, not udisksctl...

[daming]

Hello everyone,
I'm using Debian Stretch 9.6 (64bit) with Mate.

Powering off an external USB drive after unmounting crashes the system (unresponsive mouse and keyboard), requiring an hard reboot.
I had the same result with a freshly downloaded Mate Live 9.6 image.
It doesn't matter which method I use, this happens with file manager, gnome-disk-utility and even typing 'udisksctl power-off -b /dev/sdX' on the command line.
I never had this problem on 9.5, or if I boot the old kernel.
After the reset, there are some messages about the root partition:

Recovering journal
Clearing orphaned inode



Is there anything I can do to fix this?

I have the same problem with gnome

[modo72]

Hello out there,
I have the same issue under Xfce. And only if umount the external drive with gui! If umounted it with the console everthing seems okay. If I umounted it from the filemanager (Thunar) the whole system feezes down and needs a reset! It happens instantly, but not in every case, "only" in about 90% of my unmounts. It seems so that it never happens after unmounting an USB Stick or flash card. Even if I formated this stick with ext FS.

This is really serious.

BR Christian

[enry13]

I have the same problem with debian 9 and Gnome shell.
It is related to a bug introduced with the kernel : linux-image-4.9.0-8-amd64

With this kernel trying to unmount a USB3 disk by using the GUI with
the command "Safely remove drive" produces a complete not recoverable crash.
The terminal command line "umount /media/...." is safe as well the "EJECT" GUI command if present
in the contest USB menu.

As a workaround i have reinstalled and now i use as default the previous
kernel 4.9.0-7-amd64 that does not present any problem.

Clearly a kernel upgrade resolving this dangerous regression will be suitable.
I have no idea if this bug is known to debian kernel maintainers

[None1975]

I have no idea if this bug is known to debian kernel maintainers

It would be good if you report this bug to Debian maintainers. How to report a bug in Debian using reportbug, check this. Personally, this bug did not occur to me.

[enry13]

>>It would be good if you report this bug to Debian maintainers

I have verified that a report bug on this argument already exists with number:
"debian bug 914696"
https://bugs.debian.org/cgi-bin/bugrepo ... bug=914696

[None1975]

I have verified that a report bug on this argument already exists with number:
"debian bug 914696"
https://bugs.debian.org/cgi-bin/bugrepo ... bug=914696

Then add your comments and detailed description to this report.

[enry13]

Just to inform that the recent kernel update to
4.9.0-8-amd64 #1 SMP Debian 4.9.144-3

that is part of the 9.8 upgrade of debian stretch completely resolves the
problem of USB3 causing crashing on remove. I have verified
the return to a normal behavior with a usb3 stick and an external USB3 HDD
previously causing a complete
hang of the computer on "safely remove drive" menu command.