It lists the main problems users usually find when trying to install the dongle on a Linux OS, and provides possible solutions.
I have seen many posts about users trying to install their broadband internet and getting stuck at the same problem, or just asking how to install their specific version of their dongle, without having tried anything. I noticed that on the internet there is not much info either, even if most of installations share the same steps.
I am writing this guide in the attempt to unify, in the best possible way, the installation guides for most broadband dongles for a generic (beginner) Linux user. All the commands should work on any Linux distribution. For your information, the distribution I used to make this tutorial is Debian Squeeze with Gnome (GUI), and the broadband modem is an obscure Olivetti Olicard 200, which was only known to be not very Linux-friendly.
The only prerequisite is to know how to install software packages on your distribution. I explain any other step and provide commands. No other knowledge of Linux is assumed.
I copied this guide from my blog, here:
http://www.greplinux.net/2012/07/everyt ... about.html
I wrote this guide and it is not copyrighted.
1. Check that your system sees the hardware
Firstly, remove your PIN from the SIM card using a mobile phone, as it can unnecessarily complicate things.
Whenever you plug-in your usb broadband modem, the very first thing you need to check is that your systems realizes that something has been plugged-in your usb port.
I am assuming that your mobile broadband dongle is working on the first place (can check on a Windows system, if you are not sure). A flashing led should show you that the electronics are working inside.
Run this command to see if the modem is recognized as plugged-in a usb port:
Code: Select all
$ lsusb
Code: Select all
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 003: ID 04b4:0060 Cypress Semiconductor Corp.
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[b] Bus 002 Device 028: ID 0b3c:f000 Olivetti Techcenter[/b]
Bus 002 Device 003: ID 04f2:b044 Chicony Electronics Co., Ltd Acer CrystalEye Webcam
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Take a note of the codes just before the brand name. In my case the numbers are:
Code: Select all
0b3c:f000
This product code is used for storage usb dongles. As most of mobile broadband dongles are also capable to store data, the system is not recognizing the dongle as a modem. If you have this product code as well, proceed to Step 2.
If you see a code like XXXX or cXXX (where X is any number from 0-9), instead, your system already recognizes your dongle as a wireless broadband modem.
You can skip Step 2 and proceed to Step 3.
2. Switch device from usb to modem
(this step requires an internet connection, you can gather the packages from another pc if you are not able to connect on your own)
Your internet dongle is not recognized as such. We will use a software to let your system recognize it, called usb-modeswitch. You need to install two packages which are part of this program: usb-modeswitch and usb-modeswitch-data. Also install wdial and modemmanager, if for some reason are not installed already.
Once installed, you will need to type a single command to switch the mode of your internet dongle from storage usb-stick to modem.
Firstly, you will need some information:
- The vendor code, as found before usign lsusb (in my case 0b3c)
- The product code, as found before usign lsusb (in my case f000)
- A Hex key, associated to vendor and product code.
You already have vendor and product code, but in order to obtain the Hex key, you need to run the following command, which will retrieve the Hex key from your system.
Code: Select all
$ cat /etc/usb_modeswitch.d/[vendor code]\:[product code] | grep MessageContent
Code: Select all
$ cat /etc/usb_modeswitch.d/0b3c\:f000 | grep MessageContent
Code: Select all
$ sudo usb_modeswitch --default-vendor [vendor code] --default-product [product code] --message-content [hex key]
Code: Select all
$ sudo usb_modeswitch --default-vendor 0x0b3c --default-product 0xf000 --message-content 5553424312345678c000000080010606f50402527000000000000000000000
After you run this code, you should see an output of this kind:
Code: Select all
Looking for default devices ...
Found devices in default mode, class or configuration (1)
Accessing device 003 on bus 001 ...
Getting the current device configuration ...
OK, got current device configuration (1)
Using endpoints 0x01 (out) and 0x81 (in)
Using endpoints 0x01 (out) and 0x81 (in)
Inquiring device details; driver will be detached ...
Looking for active driver ...
OK, driver found ("usb-storage")
OK, driver "usb-storage" detached
SCSI inquiry data (for identification)
-------------------------
Vendor String: USBModem
Model String: MMC Storage
Revision String: 2.31
-------------------------
USB description data (for identification)
-------------------------
Manufacturer: USBModem
Product: HSPA Data Card
Serial No.: 1234567890ABCDEF
-------------------------
Setting up communication with interface 0 ...
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Resetting response endpoint 0x81
Resetting message endpoint 0x01
Device is gone, skipping any further commands
-> Run lsusb to note any changes. Bye.
Code: Select all
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 04b4:0060 Cypress Semiconductor Corp.
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 005: ID 0b3c:[b]c005[/b] Olivetti Techcenter
Bus 002 Device 003: ID 04f2:b044 Chicony Electronics Co., Ltd Acer CrystalEye Webcam
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
3. Install your internet dongle (the normal way)
If you are lucky enough, your broadband internet might be working already. In the GUI, click on the Network Manager icon and see if the Broadband connection is available. If it is, click on it to set up a new connection and proceed to Step 4.
Otherwise, try to run on a terminal:
Code: Select all
$ sudo modprobe usbserial vendor=[vendor code] product=[product code]
Code: Select all
$ sudo modprobe usbserial vendor=0x0b3c product=0xc005
If even this method did not work (as it did not on my Olidata 200), and your Network Manager does not recognize the device, it means that you will need to find another way to let it work, so jump this section and go to Step 5.
Now that you have your working dongle, you need to do some final setups before configuring it. In order to get the modprobe command run at every boot, you need to append the previous command to /etc/rc.local, by running as root:
Code: Select all
$ su -
Code: Select all
# sed -i '$ d' /etc/rc.local; echo 'modprobe usbserial vendor=0x0b3c product=0xc005' >> /etc/rc.local; echo 'exit 0' >> /etc/rc.local
4. Connect to the internet
You now need to set up a new connection with your broadband dongle. If a connection wizard opens, you can follow the instructions on screen and it will automatically configure your dongle.
It may happen that your dongle does not like the network manager configuration. You can get around the problem using wvdial.
Code: Select all
$ sudo gedit /etc/wvdial.conf
Code: Select all
[Dialer Defaults]
Modem = /dev/ttyUSB0
ISDN = 0
Modem Type = Analog Modem
Baud = 460800
Init1 = ATX3
Init2 = AT&F Q0 V1 E0 S0=0 &C1 &D2 +FCLASS=0
Init3 = at+cgdcont=1,"IP","[i][APN][/i]"
Phone = *99#
Dial Attempts = 5
Stupid Mode = on
Dial Command = ATDT
Idle Seconds = 7200
Ask Passwords = 0
Password = "[i][PW][/i]"
Username = "[i][UN][/i]"
Carrier Check = on
New PPPD = 1
Auto DNS = on
Then, you can connect using
Code: Select all
$ sudo wvdial
5. Install your internet dongle (the alternative way)
If the "normal" way to install your dongle did not work, you should consider using a very neat utility, which usually works with picky internet dongles.
It is called Sakis 3G.
You just need to download it and extract it:
Code: Select all
$ wget http://www.sakis3g.org/versions/latest/binary-free/sakis3g.gz
$ gunzip sakis3g.gz
$ chmod +x sakis3g
Code: Select all
$ sudo apt-get remove modemmanager
Code: Select all
$ ./sakis3g --interactive
- Connect with 3G
- USB Device
- Select USB Device (the name should be familiar)
- Select Interface (only one should work as modem)
- Select APN (should auto-detect)
If you see a screen informing you that the device connected: congratulations, you managed to make your internet wireless dongle work on a Linux OS!
This is my first how-to, please reply to suggest other methods, mistakes (I'm sure there will be many) or if you have any problems.
Hope it helped
Giulio