Scheduled Maintenance: We are aware of an issue with Google, AOL, and Yahoo services as email providers which are blocking new registrations. We are trying to fix the issue and we have several internal and external support tickets in process to resolve the issue. Please see: viewtopic.php?t=158230

 

 

 

TCP failover doesn't work as expected

Linux Kernel, Network, and Services configuration.
Post Reply
Message
Author
zenichev
Posts: 1
Joined: 2018-03-20 13:41

TCP failover doesn't work as expected

#1 Post by zenichev »

Hi community.

I'm trying to build up a tcp failover cluster.
I'm trying to save and restore active tcp sessions (that belong to
master side) on the salve side, when master experience the failover. So
that, I would have needed tcp sockets opened on slave side (that were
indeed started on the master side).

The main goal is to make it working for kamailio (SER) daemon. I'm
trying to reach real-time HA cluster for calls that are being on the
line and save them when master experience the failure.

What I've already done:
1. Created well-formed rule set for iptables:
-A INPUT -i eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT
-A INPUT -i eth0 -d 10.100.100.27/32 -j DROP
-A INPUT -m state --state INVALID -j LOG

-P FORWARD DROP
-A FORWARD -i eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT
-A FORWARD -i eth0 -d 10.100.100.27/32 -j DROP
-A FORWARD -m state --state INVALID -j LOG

where 10.100.100.27 - VIP address
The same rule set is stored on the slave side.

2. Configured conntracd:
Sync {
Mode FTFW {
DisableExternalCache Off
CommitTimeout 1800
PurgeTimeout 5
}

UDP {
IPv4_address 10.100.100.28
IPv4_Destination_Address 10.100.100.29
Port 3780
Interface eth0
SndSocketBuffer 1249280
RcvSocketBuffer 1249280
Checksum on
}

Options {
ExpectationSync {
sip
ftp
}
}
}

General {
Nice -20
HashSize 32768
HashLimit 131072
LogFile on
Syslog on
LockFile /var/lock/conntrack.lock
UNIX {
Path /var/run/conntrackd.ctl
Backlog 20
}
NetlinkBufferSize 2097152
NetlinkBufferSizeMaxGrowth 8388608
Filter From Userspace {
Protocol Accept {
TCP
UDP
ICMP
}
Address Ignore {
}
}
}

where 10.100.100.28 - master and 10.100.100.29 -
salve.
The same config file is stored on the slave side, but addresses in UDP
section are swapped.
I tried to use Address Ignore block, where I made an effort to add ip
addresses belong to the node, but with this one it didn't work at all -
there was no exchange of conntrackd traffic between cluster nodes. So I
leaved it empty.

3. Configured keepalived:

vrrp_instance E1 {
interface eth0
state BACKUP
virtual_router_id 61
advert_int 1
authentication {
auth_type PASS
auth_pass herepassword
}
virtual_ipaddress {
10.100.100.27/27 dev eth0
}
nopreempt
garp_master_delay 1

notify_master "/etc/conntrackd/primary-backup.sh primary"
notify_backup "/etc/conntrackd/primary-backup.sh backup"
notify_fault "/etc/conntrackd/primary-backup.sh fault"
}

where primary-backup.sh is a script, that is provided with conntrackd
libraries.
You will ask me, why I don't use dedicated link for conntrackd? I used
it for a while, but as matter of fact it didn't change anything, so I
simplified the assignment for myself and made it deprecated.


How the process of failover looks like for the current moment:

1. I use telnet/ssh/ftp to connect to VIP address located (for current
moment) on master side;
1.1. Master side experience a fail - I bring down the eth0 link;
2. Backup node see the problem and execute:
/etc/conntrackd/primary-backup.sh primary
so the following sequence of conntrackd command are executed:
/usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -c
/usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -f
/usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -R
/usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -B

3. I can see the needed telnet/ssh/ftp session on the backup node by
command: conntrackd -i
It has state - ESTABLISHED state (I'm confident that this is
session I need, cuz I remember the client's port was used for connection
on master node).

4. But when I try to send packets (commands) from my client, server
resets the TCP session with [R] flag. Tcpdump output on the backups node
shows only 2 rows:

11:12:26.621001 IP telnet.client.test.56238 >
10.100.100.27.telnet: Flags [P.], seq 1380562259:1380562261,
ack 1731331297, win 237, options [nop,nop,TS val 43239685 ecr 81905017],
length 2
11:12:26.621083 IP 10.100.100.27.telnet >
telnet.client.test.56238: Flags [R], seq 1731331297, win 0, length 0

As you can see, firewall accepts the traffic (in INPUT and FORWARD
chains),this means that session exists on the backup internal
cache/kernel table (otherwise iptables would drop the packet), but it
then resets it, why?
I tried to test it with ssh, telnet and ftp. No success at all.
I also tried to remove flushing command, so that sequence was changed to :
/usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -c
/usr/sbin/conntrackd -C /etc/conntrackd/conntrackd.conf -R

and it also didn't work.

So if someone has the needed experience, please don't be apathetic, help
a bit.
At least I need a hint where to look for a problem.


--
BR, Donat Zenichev

Post Reply