I've been struggling with this problem for a while. I have performed an installation of Debian 10.6.0 on my 64-bit machine (dual boot with Windows 10), and during the installation (netinst) all went ok (DHCP configured, got IP address, downloaded from the mirror, etc.).
However, when I now boot into Debian, the wired won't connect. A notification appears which says "Activation of network connection failed".
I disabled Windows fast startup option as some website stated for solving the problem, but nothing.
This is my lshw output for the Ethernet interface:
Code: Select all
*-network
description: Ethernet interface
product: Ethernet Connection I217-V
vendor: Intel Corporation
physical id: 19
bus info: pci@0000:00:19.0
logical name: eno1
version: 04
serial: 74:d0:2b:a2:63:bb
size: 100Mbit/s
capacity: 1Gbit/s
width: 32 bits
clock: 33MHz
capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=3.8.4-NAPI duplex=full firmware=0.13-4 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s
resources: irq:24 memory:f7f00000-f7f1ffff memory:f7f39000-f7f39fff ioport:f040(size=32)
Code: Select all
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 74:d0:2b:a2:63:bb brd ff:ff:ff:ff:ff:ff
3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 24:0a:64:10:d6:48 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.69/24 brd 192.168.1.255 scope global dynamic noprefixroute wlp3s0
valid_lft 20722sec preferred_lft 20722sec
inet6 fe80::5e8a:8604:14d9:ad06/64 scope link noprefixroute
valid_lft forever preferred_lft forever
Code: Select all
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 74:d0:2b:a2:63:bb brd ff:ff:ff:ff:ff:ff
inet 192.168.1.2/24 brd 192.168.1.255 scope global noprefixroute eno1
valid_lft forever preferred_lft forever
inet6 fe80::40ec:3796:ca3e:7968/64 scope link noprefixroute
valid_lft forever preferred_lft forever
3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 24:0a:64:10:d6:48 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.69/24 brd 192.168.1.255 scope global dynamic noprefixroute wlp3s0
valid_lft 20494sec preferred_lft 20494sec
inet6 fe80::5e8a:8604:14d9:ad06/64 scope link noprefixroute
valid_lft forever preferred_lft forever
The routes seem to be fine, as this output of ip route list shows:
Code: Select all
default via 192.168.1.1 dev eno1 proto static metric 100
192.168.1.0/24 dev eno1 proto kernel scope link src 192.168.1.2 metric 100
I would really appreciate any help.