I'm trying to setup a new laptop and I'm struggling to get the external display connected.
No mater what, this is always the result:
Code: Select all
cris@omen:~$ xrandr
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192
eDP-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 344mm x 194mm
1920x1080 60.02*+ 40.03
DP-1 disconnected (normal left inverted right x axis y axis)
1920x1080 60.02
HDMI-1 disconnected (normal left inverted right x axis y axis)
Code: Select all
cris@omen:~$ xrandr --verbose
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192
eDP-1 connected primary 1920x1080+0+0 (0x46) normal (normal left inverted right x axis y axis) 344mm x 194mm
Identifier: 0x42
Timestamp: 2755457
Subpixel: unknown
Gamma: 1.0:1.0:1.0
Brightness: 1.0
Clones:
CRTC: 0
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
EDID:
00ffffffffffff0030e48c0500000000
001a01049522137803a1c59459578f27
20505400000001010101010101010101
0101010101012e3680a070381f403020
350058c210000019222480a070381f40
3020350058c210000019000000fd0028
3c43430e010a20202020202000000002
000c47ff0a3c6e1c151f6e00000000bb
scaling mode: Full aspect
supported: Full, Center, Full aspect
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
1920x1080 (0x46) 138.700MHz -HSync -VSync *current +preferred
h: width 1920 start 1968 end 2000 total 2080 skew 0 clock 66.68KHz
v: height 1080 start 1083 end 1088 total 1111 clock 60.02Hz
1920x1080 (0x47) 92.500MHz -HSync -VSync
h: width 1920 start 1968 end 2000 total 2080 skew 0 clock 44.47KHz
v: height 1080 start 1083 end 1088 total 1111 clock 40.03Hz
DP-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x43
Timestamp: 2755457
Subpixel: unknown
Clones: HDMI-1
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
1920x1080 (0x46) 138.700MHz -HSync -VSync
h: width 1920 start 1968 end 2000 total 2080 skew 0 clock 66.68KHz
v: height 1080 start 1083 end 1088 total 1111 clock 60.02Hz
HDMI-1 disconnected (normal left inverted right x axis y axis)
Identifier: 0x44
Timestamp: 2755457
Subpixel: unknown
Clones: DP-1
CRTCs: 0 1 2
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
aspect ratio: Automatic
supported: Automatic, 4:3, 16:9
Broadcast RGB: Automatic
supported: Automatic, Full, Limited 16:235
audio: auto
supported: force-dvi, off, auto, on
link-status: Good
supported: Good, Bad
cris@omen:~$ xrandr --output DP-1 --mode 1920x1080 --auto --right-of eDP-1 --verbose
screen 0: 3840x1080 1013x285 mm 96.25dpi
crtc 1: 1920x1080 60.02 +1920+0 "DP-1"
xrandr: Configure crtc 1 failed
crtc 0: disable
crtc 1: disable
crtc 2: disable
screen 0: revert
crtc 0: revert
crtc 1: revert
crtc 2: revert
Code: Select all
[ 159.283] (--) Log file renamed from "/var/log/Xorg.pid-1420.log" to "/var/log/Xorg.0.log"
[ 159.283]
X.Org X Server 1.19.5
Release Date: 2017-10-12
[ 159.283] X Protocol Version 11, Revision 0
[ 159.283] Build Operating System: Linux 4.9.0-4-amd64 x86_64 Debian
[ 159.283] Current Operating System: Linux omen 4.14.0-rc7-amd64 #1 SMP Debian 4.14~rc7-1~exp1 (2017-10-30) x86_64
[ 159.283] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.14.0-rc7-amd64 root=UUID=dc926ef7-00bf-4127-b1b8-442c10ad5692 ro acpi_osi=! "acpi_osi=Windows 2009"
[ 159.283] Build Date: 16 October 2017 12:28:38PM
[ 159.283] xorg-server 2:1.19.5-1 (https://www.debian.org/support)
[ 159.283] Current version of pixman: 0.34.0
[ 159.283] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 159.283] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 159.283] (==) Log file: "/var/log/Xorg.0.log", Time: Mon Nov 13 15:51:37 2017
[ 159.283] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 159.283] (==) No Layout section. Using the first Screen section.
[ 159.283] (==) No screen section available. Using defaults.
[ 159.283] (**) |-->Screen "Default Screen Section" (0)
[ 159.283] (**) | |-->Monitor "<default monitor>"
[ 159.283] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 159.283] (==) Automatically adding devices
[ 159.283] (==) Automatically enabling devices
[ 159.283] (==) Automatically adding GPU devices
[ 159.283] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 159.283] (WW) The directory "/usr/share/fonts/X11/misc" does not exist.
[ 159.283] Entry deleted from font path.
[ 159.283] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[ 159.283] Entry deleted from font path.
[ 159.283] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[ 159.283] Entry deleted from font path.
[ 159.283] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[ 159.283] Entry deleted from font path.
[ 159.283] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
[ 159.283] Entry deleted from font path.
[ 159.283] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[ 159.283] Entry deleted from font path.
[ 159.283] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[ 159.283] Entry deleted from font path.
[ 159.283] (==) FontPath set to:
built-ins
[ 159.283] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 159.283] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 159.283] (II) Loader magic: 0x55d3a97eade0
[ 159.283] (II) Module ABI versions:
[ 159.283] X.Org ANSI C Emulation: 0.4
[ 159.283] X.Org Video Driver: 23.0
[ 159.283] X.Org XInput driver : 24.1
[ 159.283] X.Org Server Extension : 10.0
[ 159.284] (++) using VT number 7
[ 159.284] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 159.284] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 159.301] (--) PCI:*(0:0:2:0) 8086:591b:103c:838f rev 4, Mem @ 0xdd000000/16777216, 0xb0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072
[ 159.301] (II) LoadModule: "glx"
[ 159.301] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 159.302] (II) Module glx: vendor="X.Org Foundation"
[ 159.302] compiled for 1.19.5, module version = 1.0.0
[ 159.302] ABI class: X.Org Server Extension, version 10.0
[ 159.302] (==) Matched modesetting as autoconfigured driver 0
[ 159.302] (==) Matched fbdev as autoconfigured driver 1
[ 159.302] (==) Matched vesa as autoconfigured driver 2
[ 159.302] (==) Assigned the driver to the xf86ConfigLayout
[ 159.302] (II) LoadModule: "modesetting"
[ 159.302] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 159.302] (II) Module modesetting: vendor="X.Org Foundation"
[ 159.302] compiled for 1.19.5, module version = 1.19.5
[ 159.302] Module class: X.Org Video Driver
[ 159.302] ABI class: X.Org Video Driver, version 23.0
[ 159.302] (II) LoadModule: "fbdev"
[ 159.302] (WW) Warning, couldn't open module fbdev
[ 159.302] (II) UnloadModule: "fbdev"
[ 159.302] (II) Unloading fbdev
[ 159.302] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 159.302] (II) LoadModule: "vesa"
[ 159.302] (WW) Warning, couldn't open module vesa
[ 159.302] (II) UnloadModule: "vesa"
[ 159.302] (II) Unloading vesa
[ 159.302] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 159.302] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 159.349] (II) modeset(0): using drv /dev/dri/card0
[ 159.349] (II) modeset(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 159.349] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[ 159.350] (==) modeset(0): RGB weight 888
[ 159.350] (==) modeset(0): Default visual is TrueColor
[ 159.350] (II) Loading sub module "glamoregl"
[ 159.350] (II) LoadModule: "glamoregl"
[ 159.350] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 159.356] (II) Module glamoregl: vendor="X.Org Foundation"
[ 159.356] compiled for 1.19.5, module version = 1.0.0
[ 159.356] ABI class: X.Org ANSI C Emulation, version 0.4
[ 159.356] (II) glamor: OpenGL accelerated X.org driver based.
[ 159.378] (II) glamor: EGL version 1.4 (DRI2):
[ 159.384] (II) modeset(0): glamor initialized
[ 159.385] (II) modeset(0): Output eDP-1 has no monitor section
[ 159.385] (II) modeset(0): Output DP-1 has no monitor section
[ 159.568] (II) modeset(0): Output HDMI-1 has no monitor section
[ 159.569] (II) modeset(0): EDID for output eDP-1
[ 159.569] (II) modeset(0): Manufacturer: LGD Model: 58c Serial#: 0
[ 159.569] (II) modeset(0): Year: 2016 Week: 0
[ 159.569] (II) modeset(0): EDID Version: 1.4
[ 159.569] (II) modeset(0): Digital Display Input
[ 159.569] (II) modeset(0): 6 bits per channel
[ 159.569] (II) modeset(0): Digital interface is DisplayPort
[ 159.569] (II) modeset(0): Max Image Size [cm]: horiz.: 34 vert.: 19
[ 159.569] (II) modeset(0): Gamma: 2.20
[ 159.569] (II) modeset(0): No DPMS capabilities specified
[ 159.569] (II) modeset(0): Supported color encodings: RGB 4:4:4
[ 159.569] (II) modeset(0): First detailed timing is preferred mode
[ 159.569] (II) modeset(0): Preferred mode is native pixel format and refresh rate
[ 159.569] (II) modeset(0): Display is continuous-frequency
[ 159.569] (II) modeset(0): redX: 0.580 redY: 0.350 greenX: 0.340 greenY: 0.560
[ 159.569] (II) modeset(0): blueX: 0.155 blueY: 0.125 whiteX: 0.313 whiteY: 0.329
[ 159.569] (II) modeset(0): Manufacturer's mask: 0
[ 159.569] (II) modeset(0): Supported detailed timing:
[ 159.569] (II) modeset(0): clock: 138.7 MHz Image Size: 344 x 194 mm
[ 159.569] (II) modeset(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
[ 159.569] (II) modeset(0): v_active: 1080 v_sync: 1083 v_sync_end 1088 v_blanking: 1111 v_border: 0
[ 159.569] (II) modeset(0): Supported detailed timing:
[ 159.569] (II) modeset(0): clock: 92.5 MHz Image Size: 344 x 194 mm
[ 159.569] (II) modeset(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0
[ 159.569] (II) modeset(0): v_active: 1080 v_sync: 1083 v_sync_end 1088 v_blanking: 1111 v_border: 0
[ 159.569] (II) modeset(0): Ranges: V min: 40 V max: 60 Hz, H min: 67 H max: 67 kHz, PixClock max 145 MHz
[ 159.569] (II) modeset(0): Unknown vendor-specific block 2
[ 159.569] (II) modeset(0): EDID (in hex):
[ 159.569] (II) modeset(0): 00ffffffffffff0030e48c0500000000
[ 159.569] (II) modeset(0): 001a01049522137803a1c59459578f27
[ 159.569] (II) modeset(0): 20505400000001010101010101010101
[ 159.569] (II) modeset(0): 0101010101012e3680a070381f403020
[ 159.569] (II) modeset(0): 350058c210000019222480a070381f40
[ 159.569] (II) modeset(0): 3020350058c210000019000000fd0028
[ 159.569] (II) modeset(0): 3c43430e010a20202020202000000002
[ 159.569] (II) modeset(0): 000c47ff0a3c6e1c151f6e00000000bb
[ 159.570] (II) modeset(0): Printing probed modes for output eDP-1
[ 159.570] (II) modeset(0): Modeline "1920x1080"x60.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 159.570] (II) modeset(0): Modeline "1920x1080"x40.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 159.570] (II) modeset(0): EDID for output DP-1
[ 159.752] (II) modeset(0): EDID for output HDMI-1
[ 159.752] (II) modeset(0): Output eDP-1 connected
[ 159.752] (II) modeset(0): Output DP-1 disconnected
[ 159.752] (II) modeset(0): Output HDMI-1 disconnected
[ 159.752] (II) modeset(0): Using exact sizes for initial modes
[ 159.752] (II) modeset(0): Output eDP-1 using initial mode 1920x1080 +0+0
[ 159.752] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[ 159.752] (==) modeset(0): DPI set to (96, 96)
[ 159.752] (II) Loading sub module "fb"
[ 159.752] (II) LoadModule: "fb"
[ 159.752] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 159.752] (II) Module fb: vendor="X.Org Foundation"
[ 159.752] compiled for 1.19.5, module version = 1.0.0
[ 159.752] ABI class: X.Org ANSI C Emulation, version 0.4
[ 159.752] (==) Depth 24 pixmap format is 32 bpp
[ 159.805] (==) modeset(0): Backing store enabled
[ 159.805] (==) modeset(0): Silken mouse enabled
[ 159.805] (II) modeset(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 159.899] (==) modeset(0): DPMS enabled
[ 159.899] (II) modeset(0): [DRI2] Setup complete
[ 159.899] (II) modeset(0): [DRI2] DRI driver: i965
[ 159.899] (II) modeset(0): [DRI2] VDPAU driver: i965
[ 159.899] (--) RandR disabled
[ 159.901] (II) SELinux: Disabled on system
[ 159.906] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 159.906] (II) AIGLX: enabled GLX_ARB_create_context
[ 159.906] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 159.906] (II) AIGLX: enabled GLX_EXT_create_context_es{,2}_profile
[ 159.906] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 159.906] (II) AIGLX: enabled GLX_SGI_swap_control
[ 159.907] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 159.907] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 159.907] (II) AIGLX: enabled GLX_EXT_fbconfig_packed_float
[ 159.907] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 159.907] (II) AIGLX: enabled GLX_ARB_create_context_robustness
[ 159.907] (II) AIGLX: Loaded and initialized i965
[ 159.907] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 159.909] (II) modeset(0): Damage tracking initialized
[ 159.909] (II) modeset(0): Setting screen physical size to 508 x 285
[ 159.933] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 159.933] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 159.933] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 159.933] (II) LoadModule: "libinput"
[ 159.933] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[ 159.934] (II) Module libinput: vendor="X.Org Foundation"
[ 159.934] compiled for 1.19.3, module version = 0.26.0
[ 159.934] Module class: X.Org XInput Driver
[ 159.934] ABI class: X.Org XInput driver, version 24.1
[ 159.934] (II) Using input driver 'libinput' for 'Power Button'
[ 159.934] (**) Power Button: always reports core events
[ 159.934] (**) Option "Device" "/dev/input/event3"
[ 159.934] (**) Option "_source" "server/udev"
[ 159.935] (II) event3 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 159.935] (II) event3 - (II) Power Button: (II) device is a keyboard
[ 159.935] (II) event3 - (II) Power Button: (II) device removed
[ 159.956] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event3"
[ 159.956] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 159.956] (**) Option "xkb_model" "pc105"
[ 159.956] (**) Option "xkb_layout" "pt"
[ 159.968] (II) event3 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 159.968] (II) event3 - (II) Power Button: (II) device is a keyboard
[ 159.968] (II) config/udev: Adding input device Video Bus (/dev/input/event7)
[ 159.968] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 159.968] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[ 159.968] (II) Using input driver 'libinput' for 'Video Bus'
[ 159.968] (**) Video Bus: always reports core events
[ 159.968] (**) Option "Device" "/dev/input/event7"
[ 159.968] (**) Option "_source" "server/udev"
[ 159.969] (II) event7 - (II) Video Bus: (II) is tagged by udev as: Keyboard
[ 159.969] (II) event7 - (II) Video Bus: (II) device is a keyboard
[ 159.969] (II) event7 - (II) Video Bus: (II) device removed
[ 160.004] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input9/event7"
[ 160.004] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 160.004] (**) Option "xkb_model" "pc105"
[ 160.004] (**) Option "xkb_layout" "pt"
[ 160.005] (II) event7 - (II) Video Bus: (II) is tagged by udev as: Keyboard
[ 160.005] (II) event7 - (II) Video Bus: (II) device is a keyboard
[ 160.006] (II) config/udev: Adding input device Video Bus (/dev/input/event8)
[ 160.006] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 160.006] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[ 160.006] (II) Using input driver 'libinput' for 'Video Bus'
[ 160.006] (**) Video Bus: always reports core events
[ 160.006] (**) Option "Device" "/dev/input/event8"
[ 160.006] (**) Option "_source" "server/udev"
[ 160.006] (II) event8 - (II) Video Bus: (II) is tagged by udev as: Keyboard
[ 160.007] (II) event8 - (II) Video Bus: (II) device is a keyboard
[ 160.007] (II) event8 - (II) Video Bus: (II) device removed
[ 160.036] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:12/LNXVIDEO:01/input/input10/event8"
[ 160.036] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 8)
[ 160.036] (**) Option "xkb_model" "pc105"
[ 160.036] (**) Option "xkb_layout" "pt"
[ 160.037] (II) event8 - (II) Video Bus: (II) is tagged by udev as: Keyboard
[ 160.037] (II) event8 - (II) Video Bus: (II) device is a keyboard
[ 160.038] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 160.038] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 160.038] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 160.038] (II) Using input driver 'libinput' for 'Power Button'
[ 160.038] (**) Power Button: always reports core events
[ 160.038] (**) Option "Device" "/dev/input/event2"
[ 160.038] (**) Option "_source" "server/udev"
[ 160.039] (II) event2 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 160.039] (II) event2 - (II) Power Button: (II) device is a keyboard
[ 160.039] (II) event2 - (II) Power Button: (II) device removed
[ 160.052] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3/event2"
[ 160.052] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 9)
[ 160.052] (**) Option "xkb_model" "pc105"
[ 160.052] (**) Option "xkb_layout" "pt"
[ 160.053] (II) event2 - (II) Power Button: (II) is tagged by udev as: Keyboard
[ 160.053] (II) event2 - (II) Power Button: (II) device is a keyboard
[ 160.054] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 160.054] (II) No input driver specified, ignoring this device.
[ 160.054] (II) This device may have been added with another device file.
[ 160.055] (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/event9)
[ 160.055] (**) Logitech USB-PS/2 Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 160.055] (**) Logitech USB-PS/2 Optical Mouse: Applying InputClass "libinput pointer catchall"
[ 160.055] (II) Using input driver 'libinput' for 'Logitech USB-PS/2 Optical Mouse'
[ 160.055] (**) Logitech USB-PS/2 Optical Mouse: always reports core events
[ 160.055] (**) Option "Device" "/dev/input/event9"
[ 160.055] (**) Option "_source" "server/udev"
[ 160.116] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) is tagged by udev as: Mouse
[ 160.116] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device set to 800 DPI
[ 160.116] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device is a pointer
[ 160.117] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device removed
[ 160.148] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:046D:C01E.0001/input/input14/event9"
[ 160.148] (II) XINPUT: Adding extended input device "Logitech USB-PS/2 Optical Mouse" (type: MOUSE, id 10)
[ 160.148] (**) Option "AccelerationScheme" "none"
[ 160.148] (**) Logitech USB-PS/2 Optical Mouse: (accel) selected scheme none/0
[ 160.148] (**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration factor: 2.000
[ 160.148] (**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration threshold: 4
[ 160.208] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) is tagged by udev as: Mouse
[ 160.208] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device set to 800 DPI
[ 160.208] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device is a pointer
[ 160.209] (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/mouse0)
[ 160.209] (II) No input driver specified, ignoring this device.
[ 160.209] (II) This device may have been added with another device file.
[ 160.210] (II) config/udev: Adding input device HP Wide Vision HD Camera: HP Wi (/dev/input/event10)
[ 160.210] (**) HP Wide Vision HD Camera: HP Wi: Applying InputClass "evdev keyboard catchall"
[ 160.210] (**) HP Wide Vision HD Camera: HP Wi: Applying InputClass "libinput keyboard catchall"
[ 160.210] (II) Using input driver 'libinput' for 'HP Wide Vision HD Camera: HP Wi'
[ 160.210] (**) HP Wide Vision HD Camera: HP Wi: always reports core events
[ 160.210] (**) Option "Device" "/dev/input/event10"
[ 160.211] (**) Option "_source" "server/udev"
[ 160.211] (II) event10 - (II) HP Wide Vision HD Camera: HP Wi: (II) is tagged by udev as: Keyboard
[ 160.211] (II) event10 - (II) HP Wide Vision HD Camera: HP Wi: (II) device is a keyboard
[ 160.211] (II) event10 - (II) HP Wide Vision HD Camera: HP Wi: (II) device removed
[ 160.240] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/input/input15/event10"
[ 160.240] (II) XINPUT: Adding extended input device "HP Wide Vision HD Camera: HP Wi" (type: KEYBOARD, id 11)
[ 160.240] (**) Option "xkb_model" "pc105"
[ 160.240] (**) Option "xkb_layout" "pt"
[ 160.241] (II) event10 - (II) HP Wide Vision HD Camera: HP Wi: (II) is tagged by udev as: Keyboard
[ 160.241] (II) event10 - (II) HP Wide Vision HD Camera: HP Wi: (II) device is a keyboard
[ 160.242] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event12)
[ 160.242] (II) No input driver specified, ignoring this device.
[ 160.242] (II) This device may have been added with another device file.
[ 160.242] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event13)
[ 160.243] (II) No input driver specified, ignoring this device.
[ 160.243] (II) This device may have been added with another device file.
[ 160.243] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event14)
[ 160.243] (II) No input driver specified, ignoring this device.
[ 160.243] (II) This device may have been added with another device file.
[ 160.244] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event15)
[ 160.244] (II) No input driver specified, ignoring this device.
[ 160.244] (II) This device may have been added with another device file.
[ 160.244] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event16)
[ 160.244] (II) No input driver specified, ignoring this device.
[ 160.244] (II) This device may have been added with another device file.
[ 160.245] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event17)
[ 160.245] (II) No input driver specified, ignoring this device.
[ 160.245] (II) This device may have been added with another device file.
[ 160.245] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=9 (/dev/input/event18)
[ 160.245] (II) No input driver specified, ignoring this device.
[ 160.245] (II) This device may have been added with another device file.
[ 160.246] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=10 (/dev/input/event19)
[ 160.246] (II) No input driver specified, ignoring this device.
[ 160.246] (II) This device may have been added with another device file.
[ 160.247] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 160.247] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 160.247] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[ 160.247] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[ 160.247] (**) AT Translated Set 2 keyboard: always reports core events
[ 160.247] (**) Option "Device" "/dev/input/event0"
[ 160.247] (**) Option "_source" "server/udev"
[ 160.247] (II) event0 - (II) AT Translated Set 2 keyboard: (II) is tagged by udev as: Keyboard
[ 160.248] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device is a keyboard
[ 160.248] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device removed
[ 160.268] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 160.268] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 12)
[ 160.268] (**) Option "xkb_model" "pc105"
[ 160.268] (**) Option "xkb_layout" "pt"
[ 160.269] (II) event0 - (II) AT Translated Set 2 keyboard: (II) is tagged by udev as: Keyboard
[ 160.269] (II) event0 - (II) AT Translated Set 2 keyboard: (II) device is a keyboard
[ 160.270] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/event11)
[ 160.270] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "evdev touchpad catchall"
[ 160.270] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "libinput touchpad catchall"
[ 160.270] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "touchpad catchall"
[ 160.270] (**) SynPS/2 Synaptics TouchPad: Applying InputClass "Default clickpad buttons"
[ 160.270] (II) LoadModule: "synaptics"
[ 160.270] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 160.271] (II) Module synaptics: vendor="X.Org Foundation"
[ 160.271] compiled for 1.19.0, module version = 1.9.0
[ 160.271] Module class: X.Org XInput Driver
[ 160.271] ABI class: X.Org XInput driver, version 24.1
[ 160.271] (II) Using input driver 'synaptics' for 'SynPS/2 Synaptics TouchPad'
[ 160.271] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 160.271] (**) Option "Device" "/dev/input/event11"
[ 160.300] (--) synaptics: SynPS/2 Synaptics TouchPad: x-axis range 1270 - 5670 (res 44)
[ 160.300] (--) synaptics: SynPS/2 Synaptics TouchPad: y-axis range 1240 - 4746 (res 66)
[ 160.300] (--) synaptics: SynPS/2 Synaptics TouchPad: pressure range 0 - 255
[ 160.300] (--) synaptics: SynPS/2 Synaptics TouchPad: finger width range 0 - 15
[ 160.300] (--) synaptics: SynPS/2 Synaptics TouchPad: buttons: left right double triple
[ 160.300] (--) synaptics: SynPS/2 Synaptics TouchPad: Vendor 0x2 Product 0x7
[ 160.300] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 160.300] (**) SynPS/2 Synaptics TouchPad: always reports core events
[ 160.340] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input7/event11"
[ 160.340] (II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD, id 13)
[ 160.340] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MinSpeed is now constant deceleration 2.5
[ 160.340] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) MaxSpeed is now 1.75
[ 160.340] (**) synaptics: SynPS/2 Synaptics TouchPad: (accel) AccelFactor is now 0.036
[ 160.340] (**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
[ 160.340] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration profile 1
[ 160.340] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration factor: 2.000
[ 160.340] (**) SynPS/2 Synaptics TouchPad: (accel) acceleration threshold: 4
[ 160.340] (--) synaptics: SynPS/2 Synaptics TouchPad: touchpad found
[ 160.341] (II) config/udev: Adding input device SynPS/2 Synaptics TouchPad (/dev/input/mouse1)
[ 160.341] (**) SynPS/2 Synaptics TouchPad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 160.342] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/event4)
[ 160.342] (II) No input driver specified, ignoring this device.
[ 160.342] (II) This device may have been added with another device file.
[ 160.342] (II) config/udev: Adding input device ST LIS3LV02DL Accelerometer (/dev/input/js0)
[ 160.342] (II) No input driver specified, ignoring this device.
[ 160.342] (II) This device may have been added with another device file.
[ 160.343] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[ 160.343] (II) No input driver specified, ignoring this device.
[ 160.343] (II) This device may have been added with another device file.
[ 160.344] (II) config/udev: Adding input device HP WMI hotkeys (/dev/input/event6)
[ 160.344] (**) HP WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 160.344] (**) HP WMI hotkeys: Applying InputClass "libinput keyboard catchall"
[ 160.344] (II) Using input driver 'libinput' for 'HP WMI hotkeys'
[ 160.344] (**) HP WMI hotkeys: always reports core events
[ 160.344] (**) Option "Device" "/dev/input/event6"
[ 160.344] (**) Option "_source" "server/udev"
[ 160.345] (II) event6 - (II) HP WMI hotkeys: (II) is tagged by udev as: Keyboard Switch
[ 160.345] (II) event6 - (II) HP WMI hotkeys: (II) device is a keyboard
[ 160.345] (II) event6 - (II) HP WMI hotkeys: (II) device removed
[ 160.384] (**) Option "config_info" "udev:/sys/devices/virtual/input/input8/event6"
[ 160.384] (II) XINPUT: Adding extended input device "HP WMI hotkeys" (type: KEYBOARD, id 14)
[ 160.384] (**) Option "xkb_model" "pc105"
[ 160.384] (**) Option "xkb_layout" "pt"
[ 160.385] (II) event6 - (II) HP WMI hotkeys: (II) is tagged by udev as: Keyboard Switch
[ 160.385] (II) event6 - (II) HP WMI hotkeys: (II) device is a keyboard
[ 164.912] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 164.912] (II) modeset(0): Using EDID range info for horizontal sync
[ 164.912] (II) modeset(0): Using EDID range info for vertical refresh
[ 164.912] (II) modeset(0): Printing DDC gathered Modelines:
[ 164.912] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 164.912] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 165.529] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 165.529] (II) modeset(0): Using hsync ranges from config file
[ 165.529] (II) modeset(0): Using vrefresh ranges from config file
[ 165.529] (II) modeset(0): Printing DDC gathered Modelines:
[ 165.529] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 165.529] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 1693.432] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 1693.432] (II) modeset(0): Using hsync ranges from config file
[ 1693.432] (II) modeset(0): Using vrefresh ranges from config file
[ 1693.432] (II) modeset(0): Printing DDC gathered Modelines:
[ 1693.432] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 1693.432] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 1693.638] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 1693.638] (II) modeset(0): Using hsync ranges from config file
[ 1693.638] (II) modeset(0): Using vrefresh ranges from config file
[ 1693.638] (II) modeset(0): Printing DDC gathered Modelines:
[ 1693.638] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 1693.638] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 2089.796] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 2089.796] (II) modeset(0): Using hsync ranges from config file
[ 2089.796] (II) modeset(0): Using vrefresh ranges from config file
[ 2089.796] (II) modeset(0): Printing DDC gathered Modelines:
[ 2089.796] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 2089.796] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 2089.981] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 2089.982] (II) modeset(0): Using hsync ranges from config file
[ 2089.982] (II) modeset(0): Using vrefresh ranges from config file
[ 2089.982] (II) modeset(0): Printing DDC gathered Modelines:
[ 2089.982] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 2089.982] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 2102.726] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 2102.726] (II) modeset(0): Using hsync ranges from config file
[ 2102.726] (II) modeset(0): Using vrefresh ranges from config file
[ 2102.726] (II) modeset(0): Printing DDC gathered Modelines:
[ 2102.726] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 2102.726] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 2128.009] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2128.108] (EE) modeset(0): failed to set mode: Invalid argument
[ 2128.384] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2135.744] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2135.847] (EE) modeset(0): failed to set mode: Invalid argument
[ 2136.122] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2141.364] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2141.465] (EE) modeset(0): failed to set mode: Invalid argument
[ 2141.742] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2173.533] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2173.628] (EE) modeset(0): failed to set mode: Invalid argument
[ 2173.904] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2222.972] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2223.077] (EE) modeset(0): failed to set mode: Invalid argument
[ 2223.354] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2246.227] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2246.310] (EE) modeset(0): failed to set mode: Invalid argument
[ 2246.586] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2252.145] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2252.231] (EE) modeset(0): failed to set mode: Invalid argument
[ 2252.507] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2724.900] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2724.999] (EE) modeset(0): failed to set mode: Invalid argument
[ 2725.296] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2731.766] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 2731.766] (II) modeset(0): Using hsync ranges from config file
[ 2731.766] (II) modeset(0): Using vrefresh ranges from config file
[ 2731.766] (II) modeset(0): Printing DDC gathered Modelines:
[ 2731.766] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 2731.766] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 2744.746] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2744.841] (EE) modeset(0): failed to set mode: Invalid argument
[ 2745.140] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2750.733] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2750.815] (EE) modeset(0): failed to set mode: Invalid argument
[ 2751.114] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2752.804] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2752.903] (EE) modeset(0): failed to set mode: Invalid argument
[ 2753.203] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 2754.221] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 2754.307] (EE) modeset(0): failed to set mode: Invalid argument
[ 2754.583] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
[ 3488.608] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3488.609] (II) modeset(0): Using hsync ranges from config file
[ 3488.609] (II) modeset(0): Using vrefresh ranges from config file
[ 3488.609] (II) modeset(0): Printing DDC gathered Modelines:
[ 3488.609] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3488.609] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3491.821] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3491.821] (II) modeset(0): Using hsync ranges from config file
[ 3491.821] (II) modeset(0): Using vrefresh ranges from config file
[ 3491.821] (II) modeset(0): Printing DDC gathered Modelines:
[ 3491.821] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3491.821] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3499.735] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3499.735] (II) modeset(0): Using hsync ranges from config file
[ 3499.735] (II) modeset(0): Using vrefresh ranges from config file
[ 3499.735] (II) modeset(0): Printing DDC gathered Modelines:
[ 3499.735] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3499.735] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3519.416] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3519.416] (II) modeset(0): Using hsync ranges from config file
[ 3519.416] (II) modeset(0): Using vrefresh ranges from config file
[ 3519.416] (II) modeset(0): Printing DDC gathered Modelines:
[ 3519.416] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3519.416] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3647.159] (II) config/udev: removing device Logitech USB-PS/2 Optical Mouse
[ 3647.159] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device removed
[ 3647.187] (II) UnloadModule: "libinput"
[ 3750.451] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3750.451] (II) modeset(0): Using hsync ranges from config file
[ 3750.451] (II) modeset(0): Using vrefresh ranges from config file
[ 3750.451] (II) modeset(0): Printing DDC gathered Modelines:
[ 3750.451] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3750.451] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3752.176] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3752.176] (II) modeset(0): Using hsync ranges from config file
[ 3752.176] (II) modeset(0): Using vrefresh ranges from config file
[ 3752.176] (II) modeset(0): Printing DDC gathered Modelines:
[ 3752.176] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3752.176] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3757.852] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3757.852] (II) modeset(0): Using hsync ranges from config file
[ 3757.852] (II) modeset(0): Using vrefresh ranges from config file
[ 3757.852] (II) modeset(0): Printing DDC gathered Modelines:
[ 3757.852] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3757.852] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3759.194] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3759.194] (II) modeset(0): Using hsync ranges from config file
[ 3759.194] (II) modeset(0): Using vrefresh ranges from config file
[ 3759.194] (II) modeset(0): Printing DDC gathered Modelines:
[ 3759.194] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3759.194] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3766.196] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3766.196] (II) modeset(0): Using hsync ranges from config file
[ 3766.196] (II) modeset(0): Using vrefresh ranges from config file
[ 3766.196] (II) modeset(0): Printing DDC gathered Modelines:
[ 3766.196] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3766.196] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3767.270] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3767.270] (II) modeset(0): Using hsync ranges from config file
[ 3767.270] (II) modeset(0): Using vrefresh ranges from config file
[ 3767.270] (II) modeset(0): Printing DDC gathered Modelines:
[ 3767.271] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3767.271] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3767.961] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3767.961] (II) modeset(0): Using hsync ranges from config file
[ 3767.961] (II) modeset(0): Using vrefresh ranges from config file
[ 3767.961] (II) modeset(0): Printing DDC gathered Modelines:
[ 3767.961] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3767.961] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3772.175] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3772.175] (II) modeset(0): Using hsync ranges from config file
[ 3772.175] (II) modeset(0): Using vrefresh ranges from config file
[ 3772.175] (II) modeset(0): Printing DDC gathered Modelines:
[ 3772.175] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3772.175] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3773.441] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3773.441] (II) modeset(0): Using hsync ranges from config file
[ 3773.441] (II) modeset(0): Using vrefresh ranges from config file
[ 3773.441] (II) modeset(0): Printing DDC gathered Modelines:
[ 3773.441] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3773.441] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3868.776] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3868.776] (II) modeset(0): Using hsync ranges from config file
[ 3868.776] (II) modeset(0): Using vrefresh ranges from config file
[ 3868.776] (II) modeset(0): Printing DDC gathered Modelines:
[ 3868.776] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3868.776] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3869.703] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3869.703] (II) modeset(0): Using hsync ranges from config file
[ 3869.703] (II) modeset(0): Using vrefresh ranges from config file
[ 3869.703] (II) modeset(0): Printing DDC gathered Modelines:
[ 3869.703] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3869.703] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3870.497] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3870.497] (II) modeset(0): Using hsync ranges from config file
[ 3870.497] (II) modeset(0): Using vrefresh ranges from config file
[ 3870.497] (II) modeset(0): Printing DDC gathered Modelines:
[ 3870.497] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3870.497] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3871.015] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3871.015] (II) modeset(0): Using hsync ranges from config file
[ 3871.015] (II) modeset(0): Using vrefresh ranges from config file
[ 3871.015] (II) modeset(0): Printing DDC gathered Modelines:
[ 3871.015] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3871.015] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3871.745] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3871.745] (II) modeset(0): Using hsync ranges from config file
[ 3871.745] (II) modeset(0): Using vrefresh ranges from config file
[ 3871.745] (II) modeset(0): Printing DDC gathered Modelines:
[ 3871.745] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3871.745] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 3891.456] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 3891.456] (II) modeset(0): Using hsync ranges from config file
[ 3891.456] (II) modeset(0): Using vrefresh ranges from config file
[ 3891.456] (II) modeset(0): Printing DDC gathered Modelines:
[ 3891.456] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 3891.456] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 4315.828] (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/mouse0)
[ 4315.828] (II) No input driver specified, ignoring this device.
[ 4315.828] (II) This device may have been added with another device file.
[ 4315.937] (II) config/udev: Adding input device Logitech USB-PS/2 Optical Mouse (/dev/input/event9)
[ 4315.937] (**) Logitech USB-PS/2 Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 4315.937] (**) Logitech USB-PS/2 Optical Mouse: Applying InputClass "libinput pointer catchall"
[ 4315.937] (II) Using input driver 'libinput' for 'Logitech USB-PS/2 Optical Mouse'
[ 4315.937] (**) Logitech USB-PS/2 Optical Mouse: always reports core events
[ 4315.937] (**) Option "Device" "/dev/input/event9"
[ 4315.937] (**) Option "_source" "server/udev"
[ 4315.996] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) is tagged by udev as: Mouse
[ 4315.996] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device set to 800 DPI
[ 4315.996] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device is a pointer
[ 4315.996] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device removed
[ 4316.028] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C01E.0002/input/input21/event9"
[ 4316.028] (II) XINPUT: Adding extended input device "Logitech USB-PS/2 Optical Mouse" (type: MOUSE, id 10)
[ 4316.030] (**) Option "AccelerationScheme" "none"
[ 4316.030] (**) Logitech USB-PS/2 Optical Mouse: (accel) selected scheme none/0
[ 4316.030] (**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration factor: 2.000
[ 4316.030] (**) Logitech USB-PS/2 Optical Mouse: (accel) acceleration threshold: 4
[ 4316.088] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) is tagged by udev as: Mouse
[ 4316.088] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device set to 800 DPI
[ 4316.088] (II) event9 - (II) Logitech USB-PS/2 Optical Mouse: (II) device is a pointer
[ 4977.739] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 4977.739] (II) modeset(0): Using hsync ranges from config file
[ 4977.739] (II) modeset(0): Using vrefresh ranges from config file
[ 4977.739] (II) modeset(0): Printing DDC gathered Modelines:
[ 4977.739] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 4977.739] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 5415.029] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 5415.029] (II) modeset(0): Using hsync ranges from config file
[ 5415.029] (II) modeset(0): Using vrefresh ranges from config file
[ 5415.029] (II) modeset(0): Printing DDC gathered Modelines:
[ 5415.029] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 5415.029] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 5431.146] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 5431.147] (II) modeset(0): Using hsync ranges from config file
[ 5431.147] (II) modeset(0): Using vrefresh ranges from config file
[ 5431.147] (II) modeset(0): Printing DDC gathered Modelines:
[ 5431.147] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 5431.147] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 5480.312] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 5480.312] (II) modeset(0): Using hsync ranges from config file
[ 5480.312] (II) modeset(0): Using vrefresh ranges from config file
[ 5480.312] (II) modeset(0): Printing DDC gathered Modelines:
[ 5480.312] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 5480.312] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 6015.889] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 6015.889] (II) modeset(0): Using hsync ranges from config file
[ 6015.889] (II) modeset(0): Using vrefresh ranges from config file
[ 6015.889] (II) modeset(0): Printing DDC gathered Modelines:
[ 6015.889] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 6015.889] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 6016.073] (II) modeset(0): EDID vendor "LGD", prod id 1420
[ 6016.073] (II) modeset(0): Using hsync ranges from config file
[ 6016.073] (II) modeset(0): Using vrefresh ranges from config file
[ 6016.073] (II) modeset(0): Printing DDC gathered Modelines:
[ 6016.073] (II) modeset(0): Modeline "1920x1080"x0.0 138.70 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (66.7 kHz eP)
[ 6016.073] (II) modeset(0): Modeline "1920x1080"x0.0 92.50 1920 1968 2000 2080 1080 1083 1088 1111 -hsync -vsync (44.5 kHz e)
[ 6291.846] (II) modeset(0): Allocate new frame buffer 3840x1080 stride
[ 6291.926] (EE) modeset(0): failed to set mode: Invalid argument
[ 6292.225] (II) modeset(0): Allocate new frame buffer 1920x1080 stride
The result is the same with modesetting or with the Intel driver installed.
The result is the same with or without bumblebee installed
The result is the same with or without bumblebee + Nvidia driver installed
Some additional info:
The machine is an HP Omen 15-ce018np
plasmashell 5.10.5
KDE Frameworks 5.37.0
Qt 5.9.2 (built against 5.9.1)
Code: Select all
cris@omen:~$ sudo lspci -v | grep VGA
[sudo] password for cris:
00:02.0 VGA compatible controller: Intel Corporation Device 591b (rev 04) (prog-if 00 [VGA controller])
01:00.0 VGA compatible controller: NVIDIA Corporation GP107M [GeForce GTX 1050 Mobile] (rev ff) (prog-if ff)
cris@omen:~$ sudo xrandr --listproviders
Providers: number : 1
Provider 0: id: 0x45 cap: 0xf, Source Output, Sink Output, Source Offload, Sink Offload crtcs: 3 outputs: 3 associated providers: 0 name:modesetting
cris@omen:~$ uname -a
Linux omen 4.14.0-rc7-amd64 #1 SMP Debian 4.14~rc7-1~exp1 (2017-10-30) x86_64 GNU/Linux
Thanks in advance
