HDIO_DRIVE_CMD(dco_identify) failed: Invalid argument.

Everything about X, Gnome, KDE, ... and everything running on it

HDIO_DRIVE_CMD(dco_identify) failed: Invalid argument.

Postby hack3rcon » 2020-12-26 13:43

Hello,
I have an SSD Drive (ADATA SU650) and when I issued below command, then it show me "HDIO_DRIVE_CMD(dco_identify) failed: Invalid argument" error:
Code: Select all
# hdparm --dco-identify /dev/sdc

/dev/sdc:
 HDIO_DRIVE_CMD(dco_identify) failed: Invalid argument

SSD Drive more information are:
Code: Select all
# hdparm -I /dev/sdc

/dev/sdc:

ATA device, with non-removable media
   Model Number:       ADATA SU650                             
   Serial Number:      XXXXXXXXXXX       
   Firmware Revision:  V8X02c08
   Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
   Used: unknown (minor revision code 0x0028)
   Supported: 10 9 8 7 6 5
   Likely used: 10
Configuration:
   Logical      max   current
   cylinders   16383   16383
   heads      16   16
   sectors/track   63   63
   --
   CHS current addressable sectors:    16514064
   LBA    user addressable sectors:   234441648
   LBA48  user addressable sectors:   234441648
The running kernel lacks CONFIG_IDE_TASK_IOCTL support for this device.
READ_LOG_EXT(0,0) failed: Invalid argument
   Logical  Sector size:                   512 bytes
   Physical Sector size:                   512 bytes
   Logical Sector-0 offset:                  0 bytes
   device size with M = 1024*1024:      114473 MBytes
   device size with M = 1000*1000:      120034 MBytes (120 GB)
   cache/buffer size  = unknown
   Form Factor: 2.5 inch
   Nominal Media Rotation Rate: Solid State Device
Capabilities:
   LBA, IORDY(can be disabled)
   Queue depth: 32
   Standby timer values: spec'd by Standard, with device specific minimum
   R/W multiple sector transfer: Max = 16   Current = 1
   DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
        Cycle time: min=120ns recommended=120ns
   PIO: pio0 pio1 pio2 pio3 pio4
        Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
   Enabled   Supported:
      *   SMART feature set
          Security Mode feature set
      *   Power Management feature set
      *   Write cache
          Look-ahead
          Host Protected Area feature set
      *   NOP cmd
      *   DOWNLOAD_MICROCODE
      *   48-bit Address feature set
      *   Mandatory FLUSH_CACHE
      *   FLUSH_CACHE_EXT
      *   SMART error logging
      *   General Purpose Logging feature set
      *   WRITE_{DMA|MULTIPLE}_FUA_EXT
      *   64-bit World wide name
      *   WRITE_UNCORRECTABLE_EXT command
      *   {READ,WRITE}_DMA_EXT_GPL commands
      *   Segmented DOWNLOAD_MICROCODE
      *   Gen1 signaling speed (1.5Gb/s)
      *   Gen2 signaling speed (3.0Gb/s)
      *   Gen3 signaling speed (6.0Gb/s)
      *   Native Command Queueing (NCQ)
      *   Phy event counters
      *   READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
          DMA Setup Auto-Activate optimization
          Device-initiated interface power management
      *   Software settings preservation
      *   SMART Command Transport (SCT) feature set
      *   SCT Error Recovery Control (AC3)
      *   SCT Features Control (AC4)
      *   SCT Data Tables (AC5)
      *   DOWNLOAD MICROCODE DMA command
      *   Data Set Management TRIM supported (limit 8 blocks)
      *   Deterministic read ZEROs after TRIM
Security:
      supported
   not   enabled
   not   locked
   not   frozen
   not   expired: security count
      supported: enhanced erase
   2min for SECURITY ERASE UNIT. 20min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 0000000000000000
   NAA      : 0
   IEEE OUI   : 000000
   Unique ID   : 000000000
Checksum: correct

Drive is not frozen.
How can I solve it?

Thank you.
hack3rcon
 
Posts: 509
Joined: 2015-02-16 09:54

Return to Desktop & Multimedia

Who is online

Users browsing this forum: No registered users and 10 guests

fashionable