Lockups occur after installation of firmware-linux-nonfree

Getting your soundcard to work, using Debian on non-i386 hardware, etc

Lockups occur after installation of firmware-linux-nonfree

Postby Debian&Me » 2014-02-15 01:54

Hi,

Since upgrading to Wheezy and installing the firmware-linux-nonfree package, I have a problem with my computer locking up. I sure can use some help since extensive googling has not.

The computer worked fine with Ubuntu Lucid 10-04. I decided to try Debian and installed wheezy 7.0. The install went well. The only problem is that 3D acceleration is not available on my ATI Radeon X300 GPU when using the default driver (xserver-xorg-video-ati). So -- I download the Mesa drivers (libgl1-mesa-dri) and firmware-linux-nonfree and install these without complication. I now have 3D acceleration, a Gnome3 desktop and all is right as rain! But then -- the computer locks up. The keyboard does not work (no response to keypresses, not even NUMLOCK or CAPSLOCK, nor REISUB and <CTRL><ALT><DEL>). No response from mouse. The screen continues to display the same image as when the lock up occurs; no distortion or artifacts. A hard reset by holding the ON-OFF button is my only recourse. Needless to say, all work is lost.

I have attempted to capture a log prior to and during the lockup. The Xorg.0.log, dmesg and syslog reveal nothing AFAICT. Another poster suggested ssh'ing with a second computer. This setup did not bear fruit because the ethernet connection fails at the time of lockup.

I have upgraded to wheezy 7.3 and am now running jessie. Still have the same issue. I found, quite accidentially, that setting the Option "RenderAccel" "False" in /usr/share/X11/xorg.conf.d/modules.conf has helped delay the lockups significantly.

My hope is to get a log of the lockup including error messages, so I can pass the information on to Debian developers. If anyone has any ideas, I am all ears. If you know a solution, I would like to hear about that too! Please find Xorg.0.log and dmesg attached below. Thanks in advance,

Specifics:
Dell Dimension 8400
ATI/AMD Radeon X300 GPU (chip ID = 1002:5b60)

Debian jessie/sid
Linux Dimension 3.12-1-686-PAE #1 SMP Debian 3.12.9-1 (2014-02-01) i686
xserver-xorg-video-ati / radeon 1:7.3.0-1
firmware-linux-nonfree 0.40
libgl1-mesa-dri (and others) 9.2.2-1

Xorg.0.log
Code: Select all
[    17.253]
X.Org X Server 1.14.5
Release Date: 2013-12-12
[    17.253] X Protocol Version 11, Revision 0
[    17.253] Build Operating System: Linux 3.2.0-4-amd64 i686 Debian
[    17.253] Current Operating System: Linux Dimension 3.12-1-686-pae #1 SMP Debian 3.12.9-1 (2014-02-01) i686
[    17.253] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.12-1-686-pae root=UUID=47f196f6-9813-454b-83fb-44ce953e4f0c ro quiet
[    17.254] Build Date: 13 December 2013  10:45:09AM
[    17.254] xorg-server 2:1.14.5-1 (Maarten Lankhorst <maarten.lankhorst@ubuntu.com>)
[    17.254] Current version of pixman: 0.32.4
[    17.254]    Before reporting problems, check http://wiki.x.org
   to make sure that you have the latest version.
[    17.254] Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    17.254] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Feb 14 12:51:02 2014
[    17.312] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    17.491] (==) No Layout section.  Using the first Screen section.
[    17.491] (**) |-->Screen "Default Screen" (0)
[    17.491] (**) |   |-->Monitor "NANAO FlexScan T2-17"
[    17.491] (**) |   |-->Device "ATI Radeon X300 [RV370] 5B60 (PCIE)"
[    17.491] (==) Automatically adding devices
[    17.491] (==) Automatically enabling devices
[    17.492] (==) Automatically adding GPU devices
[    17.544] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    17.544]    Entry deleted from font path.
[    17.545] (==) FontPath set to:
   /usr/share/fonts/X11/misc,
   /usr/share/fonts/X11/100dpi/:unscaled,
   /usr/share/fonts/X11/75dpi/:unscaled,
   /usr/share/fonts/X11/Type1,
   /usr/share/fonts/X11/100dpi,
   /usr/share/fonts/X11/75dpi,
   built-ins
[    17.545] (==) ModulePath set to "/usr/lib/xorg/modules"
[    17.545] (II) The server relies on udev to provide the list of input devices.
   If no devices become available, reconfigure udev or disable AutoAddDevices.
[    17.545] (II) Loader magic: 0xb77316a0
[    17.545] (II) Module ABI versions:
[    17.545]    X.Org ANSI C Emulation: 0.4
[    17.545]    X.Org Video Driver: 14.1
[    17.545]    X.Org XInput driver : 19.1
[    17.545]    X.Org Server Extension : 7.0
[    17.546] (II) xfree86: Adding drm device (/dev/dri/card0)
[    17.548] (--) PCI:*(0:1:0:0) 1002:5b60:1002:0302 rev 0, Mem @ 0xd0000000/134217728, 0xdfde0000/65536, I/O @ 0x0000dc00/256, BIOS @ 0x????????/131072
[    17.548] (--) PCI: (0:1:0:1) 1002:5b70:1002:0303 rev 0, Mem @ 0xdfdf0000/65536
[    17.548] (II) Open ACPI successful (/var/run/acpid.socket)
[    17.562] Initializing built-in extension Generic Event Extension
[    17.562] Initializing built-in extension SHAPE
[    17.562] Initializing built-in extension MIT-SHM
[    17.562] Initializing built-in extension XInputExtension
[    17.562] Initializing built-in extension XTEST
[    17.562] Initializing built-in extension BIG-REQUESTS
[    17.562] Initializing built-in extension SYNC
[    17.562] Initializing built-in extension XKEYBOARD
[    17.562] Initializing built-in extension XC-MISC
[    17.562] Initializing built-in extension SECURITY
[    17.562] Initializing built-in extension XINERAMA
[    17.562] Initializing built-in extension XFIXES
[    17.562] Initializing built-in extension RENDER
[    17.562] Initializing built-in extension RANDR
[    17.562] Initializing built-in extension COMPOSITE
[    17.562] Initializing built-in extension DAMAGE
[    17.562] Initializing built-in extension MIT-SCREEN-SAVER
[    17.562] Initializing built-in extension DOUBLE-BUFFER
[    17.562] Initializing built-in extension RECORD
[    17.562] Initializing built-in extension DPMS
[    17.562] Initializing built-in extension X-Resource
[    17.562] Initializing built-in extension XVideo
[    17.562] Initializing built-in extension XVideo-MotionCompensation
[    17.562] Initializing built-in extension SELinux
[    17.562] Initializing built-in extension XFree86-VidModeExtension
[    17.562] Initializing built-in extension XFree86-DGA
[    17.562] Initializing built-in extension XFree86-DRI
[    17.563] Initializing built-in extension DRI2
[    17.563] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[    17.563] (II) LoadModule: "glx"
[    17.563] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    17.588] (II) Module glx: vendor="X.Org Foundation"
[    17.588]    compiled for 1.14.5, module version = 1.0.0
[    17.588]    ABI class: X.Org Server Extension, version 7.0
[    17.589] (==) AIGLX enabled
[    17.589] Loading extension GLX
[    17.589] (II) LoadModule: "radeon"
[    17.590] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[    17.810] (II) Module radeon: vendor="X.Org Foundation"
[    17.810]    compiled for 1.14.5, module version = 7.3.0
[    17.810]    Module class: X.Org Video Driver
[    17.810]    ABI class: X.Org Video Driver, version 14.1
[    17.810] (II) RADEON: Driver for ATI Radeon chipsets:
    ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
    ATI Radeon Mobility X300 (M24) 3152 (PCIE),
    ATI FireGL M24 GL 3154 (PCIE), ATI FireMV 2400 3155 (PCI),
    ATI Radeon X600 (RV380) 3E50 (PCIE),
    ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
    ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
    ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),

                        [ ...snipped... ]

   ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
   ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5670,
   ATI Radeon HD 5570, ATI Radeon HD 5500 Series, REDWOOD,
   ATI Mobility Radeon HD 5000 Series,
   ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon Graphics,
   ATI Mobility Radeon Graphics, CEDAR,
   ATI FirePro (FireGL) Graphics Adapter,
   ATI FirePro (FireGL) Graphics Adapter, ATI FirePro 2270, CEDAR,
   ATI Radeon HD 5450, CEDAR, CEDAR, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
   CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
   AMD Radeon HD 6900 Series, AMD Radeon HD 6900 Series, CAYMAN, CAYMAN,
   CAYMAN, AMD Radeon HD 6900M Series, Mobility Radeon HD 6000 Series,
   BARTS, BARTS, Mobility Radeon HD 6000 Series,
   Mobility Radeon HD 6000 Series, BARTS, BARTS, BARTS, BARTS,
   AMD Radeon HD 6800 Series, AMD Radeon HD 6800 Series,
   AMD Radeon HD 6700 Series, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
   TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
   TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
   CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS,
   CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, TAHITI, TAHITI, TAHITI, TAHITI,
   TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI,
   TAHITI, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN,
   PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN,
   VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE,
   VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE,
   VERDE, VERDE, VERDE, OLAND, OLAND, OLAND, OLAND, OLAND, OLAND, OLAND,
   OLAND, OLAND, OLAND, OLAND, OLAND, OLAND, HAINAN, HAINAN, HAINAN,
   HAINAN, HAINAN, HAINAN, BONAIRE, BONAIRE, BONAIRE, BONAIRE, BONAIRE,
   BONAIRE, BONAIRE, BONAIRE, KABINI, KABINI, KABINI, KABINI, KABINI,
   KABINI, KABINI, KABINI, KABINI, KABINI, KABINI, KABINI, KABINI,
   KABINI, KABINI, KABINI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
   KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
   KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
   HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII,
   HAWAII, HAWAII, HAWAII, HAWAII
[    17.839] (++) using VT number 7

[    17.986] (II) [KMS] Kernel modesetting enabled.
[    17.986] (==) RADEON(0): Depth 24, (--) framebuffer bpp 32
[    17.986] (II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[    17.986] (==) RADEON(0): Default visual is TrueColor
[    17.986] (==) RADEON(0): RGB weight 888
[    17.986] (II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
[    17.986] (--) RADEON(0): Chipset: "ATI Radeon X300 (RV370) 5B60 (PCIE)" (ChipID = 0x5b60)
[    17.986] (II) Loading sub module "dri2"
[    17.986] (II) LoadModule: "dri2"
[    17.986] (II) Module "dri2" already built-in
[    17.986] (II) Loading sub module "exa"
[    17.986] (II) LoadModule: "exa"
[    17.987] (II) Loading /usr/lib/xorg/modules/libexa.so
[    18.211] (II) Module exa: vendor="X.Org Foundation"
[    18.211]    compiled for 1.14.5, module version = 2.6.0
[    18.211]    ABI class: X.Org Video Driver, version 14.1
[    18.211] (II) RADEON(0): KMS Color Tiling: enabled
[    18.211] (II) RADEON(0): KMS Color Tiling 2D: disabled
[    18.211] (II) RADEON(0): KMS Pageflipping: enabled
[    18.211] (II) RADEON(0): SwapBuffers wait for vsync: enabled
[    18.215] (II) RADEON(0): Output VGA-0 using monitor section NANAO FlexScan T2-17
[    18.238] (II) RADEON(0): Output DVI-0 has no monitor section
[    18.258] (II) RADEON(0): Output S-video has no monitor section
[    18.262] (II) RADEON(0): EDID for output VGA-0
[    18.262] (II) RADEON(0): Printing probed modes for output VGA-0
[    18.262] (II) RADEON(0): Modeline "1280x1024_75.00"x75.0  138.54  1280 1368 1504 1728  1024 1025 1028 1069 -hsync +vsync (80.2 kHz)
[    18.262] (II) RADEON(0): Modeline "1152x864_85.00"x85.0  119.65  1152 1224 1352 1552  864 865 868 907 -hsync +vsync (77.1 kHz)
[    18.262] (II) RADEON(0): Modeline "1024x768_85.00"x85.0   94.39  1024 1088 1200 1376  768 769 772 807 -hsync +vsync (68.6 kHz)
[    18.262] (II) RADEON(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    18.262] (II) RADEON(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    18.262] (II) RADEON(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    18.262] (II) RADEON(0): Modeline "848x480"x60.0   33.75  848 864 976 1088  480 486 494 517 +hsync +vsync (31.0 kHz e)
[    18.262] (II) RADEON(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 489 492 525 -hsync -vsync (31.5 kHz e)
[    18.284] (II) RADEON(0): EDID for output DVI-0
[    18.304] (II) RADEON(0): EDID for output S-video
[    18.304] (II) RADEON(0): Output VGA-0 connected
[    18.304] (II) RADEON(0): Output DVI-0 disconnected
[    18.305] (II) RADEON(0): Output S-video disconnected
[    18.305] (II) RADEON(0): Using exact sizes for initial modes
[    18.305] (II) RADEON(0): Output VGA-0 using initial mode 1152x864_85.00
[    18.305] (II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    18.305] (II) RADEON(0): mem size init: gart size :1fdff000 vram size: s:8000000 visible:7cc0000
[    18.305] (II) RADEON(0): EXA: Driver will allow EXA pixmaps in VRAM
[    18.305] (**) RADEON(0): Display dimensions: (320, 240) mm
[    18.305] (**) RADEON(0): DPI set to (91, 91)
[    18.305] (II) Loading sub module "fb"
[    18.305] (II) LoadModule: "fb"
[    18.306] (II) Loading /usr/lib/xorg/modules/libfb.so
[    18.392] (II) Module fb: vendor="X.Org Foundation"
[    18.393]    compiled for 1.14.5, module version = 1.0.0
[    18.393]    ABI class: X.Org ANSI C Emulation, version 0.4
[    18.393] (II) Loading sub module "ramdac"
[    18.393] (II) LoadModule: "ramdac"
[    18.393] (II) Module "ramdac" already built-in
[    18.393] (--) Depth 24 pixmap format is 32 bpp
[    18.420] (II) RADEON(0): [DRI2] Setup complete
[    18.420] (II) RADEON(0): [DRI2]   DRI driver: r300
[    18.420] (II) RADEON(0): [DRI2]   VDPAU driver: r300
[    18.421] (II) RADEON(0): Front buffer size: 3888K
[    18.421] (II) RADEON(0): VRAM usage limit set to 111441K
[    18.433] (==) RADEON(0): Backing store disabled
[    18.433] (II) RADEON(0): Direct rendering enabled
[    18.433] (II) RADEON(0): Render acceleration enabled for R300/R400/R500 type cards.
[    18.433] (II) EXA(0): Driver allocated offscreen pixmaps
[    18.433] (II) EXA(0): Driver registered support for the following operations:
[    18.433] (II)         Solid
[    18.433] (II)         Copy
[    18.433] (II)         Composite (RENDER acceleration)
[    18.433] (II)         UploadToScreen
[    18.433] (II)         DownloadFromScreen
[    18.433] (II) RADEON(0): Acceleration enabled
[    18.433] (==) RADEON(0): DPMS enabled
[    18.433] (==) RADEON(0): Silken mouse enabled
[    18.433] (II) RADEON(0): Set up textured video
[    18.433] (II) RADEON(0): [XvMC] Associated with Radeon Textured Video.
[    18.433] (II) RADEON(0): [XvMC] Extension initialized.
[    18.433] (II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    18.435] (WW) RADEON(0): Option "AccelMethod" is not used
[    18.435] (--) RandR disabled
[    18.462] (II) SELinux: Disabled on system
[    19.884] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    19.884] (II) AIGLX: enabled GLX_INTEL_swap_event
[    19.884] (II) AIGLX: enabled GLX_ARB_create_context
[    19.884] (II) AIGLX: enabled GLX_ARB_create_context_profile
[    19.884] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[    19.884] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[    19.884] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    19.884] (II) AIGLX: Loaded and initialized r300
[    19.884] (II) GLX: Initialized DRI2 GL provider for screen 0
[    19.939] (II) RADEON(0): Setting screen physical size to 320 x 240
[    20.223] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    20.224] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    20.224] (II) LoadModule: "evdev"
[    20.224] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    20.252] (II) Module evdev: vendor="X.Org Foundation"
[    20.252]    compiled for 1.14.3, module version = 2.8.2
[    20.252]    Module class: X.Org XInput Driver
[    20.252]    ABI class: X.Org XInput driver, version 19.1
[    20.252] (II) Using input driver 'evdev' for 'Power Button'
[    20.252] (**) Power Button: always reports core events
[    20.252] (**) evdev: Power Button: Device: "/dev/input/event2"
[    20.252] (--) evdev: Power Button: Vendor 0 Product 0x1
[    20.252] (--) evdev: Power Button: Found keys
[    20.252] (II) evdev: Power Button: Configuring as keyboard
[    20.252] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2"
[    20.252] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    20.252] (**) Option "xkb_rules" "evdev"
[    20.252] (**) Option "xkb_model" "pc105"
[    20.252] (**) Option "xkb_layout" "us"
[    20.253] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    20.253] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    20.253] (II) Using input driver 'evdev' for 'Power Button'
[    20.253] (**) Power Button: always reports core events
[    20.253] (**) evdev: Power Button: Device: "/dev/input/event1"
[    20.253] (--) evdev: Power Button: Vendor 0 Product 0x1
[    20.253] (--) evdev: Power Button: Found keys
[    20.253] (II) evdev: Power Button: Configuring as keyboard
[    20.253] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event1"
[    20.253] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[    20.253] (**) Option "xkb_rules" "evdev"
[    20.254] (**) Option "xkb_model" "pc105"
[    20.254] (**) Option "xkb_layout" "us"
[    20.254] (II) config/udev: Adding drm device (/dev/dri/card0)
[    20.255] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    20.255] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    20.255] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[    20.255] (**) AT Translated Set 2 keyboard: always reports core events
[    20.255] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[    20.255] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[    20.255] (--) evdev: AT Translated Set 2 keyboard: Found keys
[    20.255] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[    20.255] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    20.255] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 8)
[    20.255] (**) Option "xkb_rules" "evdev"
[    20.255] (**) Option "xkb_model" "pc105"
[    20.255] (**) Option "xkb_layout" "us"
[    20.256] (II) config/udev: Adding input device ImPS/2 Generic Wheel Mouse (/dev/input/event4)
[    20.256] (**) ImPS/2 Generic Wheel Mouse: Applying InputClass "evdev pointer catchall"
[    20.256] (II) Using input driver 'evdev' for 'ImPS/2 Generic Wheel Mouse'
[    20.256] (**) ImPS/2 Generic Wheel Mouse: always reports core events
[    20.256] (**) evdev: ImPS/2 Generic Wheel Mouse: Device: "/dev/input/event4"
[    20.256] (--) evdev: ImPS/2 Generic Wheel Mouse: Vendor 0x2 Product 0x5
[    20.256] (--) evdev: ImPS/2 Generic Wheel Mouse: Found 3 mouse buttons
[    20.256] (--) evdev: ImPS/2 Generic Wheel Mouse: Found scroll wheel(s)
[    20.256] (--) evdev: ImPS/2 Generic Wheel Mouse: Found relative axes
[    20.256] (--) evdev: ImPS/2 Generic Wheel Mouse: Found x and y relative axes
[    20.256] (II) evdev: ImPS/2 Generic Wheel Mouse: Configuring as mouse
[    20.256] (II) evdev: ImPS/2 Generic Wheel Mouse: Adding scrollwheel support
[    20.256] (**) evdev: ImPS/2 Generic Wheel Mouse: YAxisMapping: buttons 4 and 5
[    20.257] (**) evdev: ImPS/2 Generic Wheel Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    20.257] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input4/event4"
[    20.257] (II) XINPUT: Adding extended input device "ImPS/2 Generic Wheel Mouse" (type: MOUSE, id 9)
[    20.257] (II) evdev: ImPS/2 Generic Wheel Mouse: initialized for relative axes.
[    20.257] (**) ImPS/2 Generic Wheel Mouse: (accel) keeping acceleration scheme 1
[    20.257] (**) ImPS/2 Generic Wheel Mouse: (accel) acceleration profile 0
[    20.257] (**) ImPS/2 Generic Wheel Mouse: (accel) acceleration factor: 2.000
[    20.257] (**) ImPS/2 Generic Wheel Mouse: (accel) acceleration threshold: 4
[    20.257] (II) config/udev: Adding input device ImPS/2 Generic Wheel Mouse (/dev/input/mouse0)
[    20.257] (II) No input driver specified, ignoring this device.
[    20.258] (II) This device may have been added with another device file.
[    20.258] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[    20.258] (II) No input driver specified, ignoring this device.
[    20.258] (II) This device may have been added with another device file.
[    24.165] (II) RADEON(0): Allocate new frame buffer 1280x1024 stride 1280
[    24.165] (II) RADEON(0): VRAM usage limit set to 110332K
[    47.739] (II) RADEON(0): Allocate new frame buffer 1152x864 stride 1152
[    47.739] (II) RADEON(0): VRAM usage limit set to 111441K
Debian&Me
 
Posts: 3
Joined: 2014-02-15 00:44

Re: Lockups occur after installation of firmware-linux-nonfr

Postby Debian&Me » 2014-02-15 01:57

dmesg follows:

Code: Select all
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.12-1-686-pae (debian-kernel@lists.debian.org) (gcc version 4.8.2 (Debian 4.8.2-14) ) #1 SMP Debian 3.12.9-1 (2014-02-01)
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cfe8cbff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cfe8cc00-0x00000000cfe8ebff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cfe8ec00-0x00000000cfe90bff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000cfe90c00-0x00000000cfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fed003ff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed20000-0x00000000fed9ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000feefffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[    0.000000] SMBIOS 2.3 present.
[    0.000000] DMI: Dell Inc.                 Dimension 8400               /0J3492, BIOS A09 07/07/2006
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0xcfe8c max_arch_pfn = 0x1000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FF0000000 write-back
[    0.000000]   3 base 0CFF00000 mask FFFF00000 uncachable
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] found SMP MP-table at [mem 0x000fe710-0x000fe71f] mapped at [c00fe710]
[    0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] init_memory_mapping: [mem 0x37600000-0x377fffff]
[    0.000000]  [mem 0x37600000-0x377fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x34000000-0x375fffff]
[    0.000000]  [mem 0x34000000-0x375fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x33ffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x33ffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x37800000-0x379fdfff]
[    0.000000]  [mem 0x37800000-0x379fdfff] page 4k
[    0.000000] BRK [0x016cc000, 0x016ccfff] PGTABLE
[    0.000000] BRK [0x016cd000, 0x016cefff] PGTABLE
[    0.000000] RAMDISK: [mem 0x3670e000-0x3737efff]
[    0.000000] ACPI: RSDP 000febf0 00014 (v00 DELL  )
[    0.000000] ACPI: RSDT 000fcc96 0003C (v01 DELL    8400    00000007 ASL  00000061)
[    0.000000] ACPI: FACP 000fccd2 00074 (v01 DELL    8400    00000007 ASL  00000061)
[    0.000000] ACPI: DSDT fffc76a0 02B21 (v01   DELL    dt_ex 00001000 MSFT 0100000D)
[    0.000000] ACPI: FACS cfe8cc00 00040
[    0.000000] ACPI: SSDT fffca1c1 000A7 (v01   DELL    st_ex 00001000 MSFT 0100000D)
[    0.000000] ACPI: APIC 000fcd46 00092 (v01 DELL    8400    00000007 ASL  00000061)
[    0.000000] ACPI: BOOT 000fcdd8 00028 (v01 DELL    8400    00000007 ASL  00000061)
[    0.000000] ACPI: MCFG 000fce00 0003E (v01 DELL    8400    00000007 ASL  00000061)
[    0.000000] ACPI: HPET 000fce3e 00038 (v01 DELL    8400    00000007 ASL  00000061)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 2436MB HIGHMEM available.
[    0.000000] 889MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 379fe000
[    0.000000]   low ram: 0 - 379fe000
[    0.000000] BRK [0x016cf000, 0x016cffff] PGTABLE
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   Normal   [mem 0x01000000-0x379fdfff]
[    0.000000]   HighMem  [mem 0x379fe000-0xcfe8bfff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009ffff]
[    0.000000]   node   0: [mem 0x00100000-0xcfe8bfff]
[    0.000000] On node 0 totalpages: 851499
[    0.000000] free_area_init_node: node 0, pgdat c1598900, node_mem_map f4d0e020
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3999 pages, LIFO batch:0
[    0.000000]   Normal zone: 1748 pages used for memmap
[    0.000000]   Normal zone: 223742 pages, LIFO batch:31
[    0.000000]   HighMem zone: 4874 pages used for memmap
[    0.000000]   HighMem zone: 623758 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x07] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x03] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x05] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 8 CPUs, 6 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[    0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[    0.000000] e820: [mem 0xd0000000-0xdfffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:8 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @f797c000 s35648 r0 d21696 u57344
[    0.000000] pcpu-alloc: s35648 r0 d21696 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 849719
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.12-1-686-pae root=UUID=47f196f6-9813-454b-83fb-44ce953e4f0c ro quiet
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (000379fe:000cfe8c)
[    0.000000] Memory: 3358268K/3405996K available (4131K kernel code, 373K rwdata, 1264K rodata, 520K init, 580K bss, 47728K reserved, 2495032K highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffd35000 - 0xfffff000   (2856 kB)
[    0.000000]     pkmap   : 0xffa00000 - 0xffc00000   (2048 kB)
[    0.000000]     vmalloc : 0xf81fe000 - 0xff9fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf79fe000   ( 889 MB)
[    0.000000]       .init : 0xc15a5000 - 0xc1627000   ( 520 kB)
[    0.000000]       .data : 0xc1409078 - 0xc15a4680   (1645 kB)
[    0.000000]       .text : 0xc1000000 - 0xc1409078   (4132 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] Hierarchical RCU implementation.
[    0.000000]    RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]    RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=8.
[    0.000000] NR_IRQS:2304 nr_irqs:744 16
[    0.000000] CPU 0 irqstacks, hard=f7408000 soft=f740a000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2992.630 MHz processor
[    0.004003] Calibrating delay loop (skipped), value calculated using timer frequency.. 5985.26 BogoMIPS (lpj=11970520)
[    0.004008] pid_max: default: 32768 minimum: 301
[    0.004050] Security Framework initialized
[    0.004058] AppArmor: AppArmor disabled by boot time parameter
[    0.004060] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.004083] Mount-cache hash table entries: 512
[    0.004368] Initializing cgroup subsys memory
[    0.004385] Initializing cgroup subsys devices
[    0.004389] Initializing cgroup subsys freezer
[    0.004391] Initializing cgroup subsys net_cls
[    0.004395] Initializing cgroup subsys blkio
[    0.004398] Initializing cgroup subsys perf_event
[    0.004439] CPU: Physical Processor ID: 0
[    0.004442] CPU: Processor Core ID: 0
[    0.004446] mce: CPU supports 4 MCE banks
[    0.004460] CPU0: Thermal monitoring enabled (TM1)
[    0.004476] Last level iTLB entries: 4KB 64, 2MB 64, 4MB 64
[    0.004476] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 64
[    0.004476] tlb_flushall_shift: 6
[    0.004594] Freeing SMP alternatives memory: 20K (c1627000 - c162c000)
[    0.005921] ACPI: Core revision 20130725
[    0.036706] ACPI: All ACPI Tables successfully acquired
[    0.037092] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.037466] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.077160] smpboot: CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz (fam: 0f, model: 03, stepping: 04)
[    0.080000] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[    0.080000] ... version:                0
[    0.080000] ... bit width:              40
[    0.080000] ... generic registers:      18
[    0.080000] ... value mask:             000000ffffffffff
[    0.080000] ... max period:             0000007fffffffff
[    0.080000] ... fixed-purpose events:   0
[    0.080000] ... event mask:             000000000003ffff
[    0.080000] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.080000] CPU 1 irqstacks, hard=f74c6000 soft=f74c8000
[    0.080000] smpboot: Booting Node   0, Processors  #   1 OK
[    0.008000] Initializing CPU#1
[    0.088068] Brought up 2 CPUs
[    0.088076] smpboot: Total of 2 processors activated (11970.52 BogoMIPS)
[    0.089089] devtmpfs: initialized
[    0.089089] PM: Registering ACPI NVS region [mem 0xcfe8cc00-0xcfe8ebff] (8192 bytes)
[    0.089089] NET: Registered protocol family 16
[    0.089089] cpuidle: using governor ladder
[    0.089089] cpuidle: using governor menu
[    0.089089] ACPI: bus type PCI registered
[    0.089089] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.089089] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.089089] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.089089] PCI: Using MMCONFIG for extended config space
[    0.089089] PCI: Using configuration type 1 for base access
[    0.092103] bio: create slab <bio-0> at 0
[    0.092103] ACPI: Added _OSI(Module Device)
[    0.092103] ACPI: Added _OSI(Processor Device)
[    0.092103] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.092103] ACPI: Added _OSI(Processor Aggregator Device)
[    0.092820] ACPI: EC: Look up EC in DSDT
[    0.104199] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.112973] ACPI: Interpreter enabled
[    0.113005] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130725/hwxface-571)
[    0.113029] ACPI: (supports S0 S1 S3 S4 S5)
[    0.113032] ACPI: Using IOAPIC for interrupt routing
[    0.113112] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[    0.113206] ACPI: No dock devices found.
[    0.199765] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.199775] acpi PNP0A03:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[    0.199779] acpi PNP0A03:00: Unable to request _OSC control (_OSC support mask: 0x08)
[    0.207057] acpi PNP0A03:00: host bridge window [io  0x0000-0x0cf7] (ignored)
[    0.207063] acpi PNP0A03:00: host bridge window [io  0x0d00-0xffff] (ignored)
[    0.207067] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[    0.207071] acpi PNP0A03:00: host bridge window [mem 0xcff00000-0xdfffffff] (ignored)
[    0.207074] acpi PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff] (ignored)
[    0.207078] PCI: root bus 00: using default resources
[    0.207481] PCI host bridge to bus 0000:00
[    0.207487] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.207491] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.207495] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
[    0.207510] pci 0000:00:00.0: [8086:2584] type 00 class 0x060000
[    0.207748] pci 0000:00:01.0: [8086:2585] type 01 class 0x060400
[    0.207807] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.207968] pci 0000:00:01.0: System wakeup disabled by ACPI
[    0.208064] pci 0000:00:1c.0: [8086:2660] type 01 class 0x060400
[    0.208147] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.208313] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.208373] pci 0000:00:1c.1: [8086:2662] type 01 class 0x060400
[    0.208456] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.208620] pci 0000:00:1c.1: System wakeup disabled by ACPI
[    0.208682] pci 0000:00:1d.0: [8086:2658] type 00 class 0x0c0300
[    0.208731] pci 0000:00:1d.0: reg 0x20: [io  0xff80-0xff9f]
[    0.208910] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.208966] pci 0000:00:1d.1: [8086:2659] type 00 class 0x0c0300
[    0.209014] pci 0000:00:1d.1: reg 0x20: [io  0xff60-0xff7f]
[    0.209191] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.209247] pci 0000:00:1d.2: [8086:265a] type 00 class 0x0c0300
[    0.209294] pci 0000:00:1d.2: reg 0x20: [io  0xff40-0xff5f]
[    0.209472] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.209529] pci 0000:00:1d.3: [8086:265b] type 00 class 0x0c0300
[    0.209577] pci 0000:00:1d.3: reg 0x20: [io  0xff20-0xff3f]
[    0.209757] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.209821] pci 0000:00:1d.7: [8086:265c] type 00 class 0x0c0320
[    0.209845] pci 0000:00:1d.7: reg 0x10: [mem 0xffa80800-0xffa80bff]
[    0.209938] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.210146] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.210359] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.210418] pci 0000:00:1e.2: [8086:266e] type 00 class 0x040100
[    0.210438] pci 0000:00:1e.2: reg 0x10: [io  0xec00-0xecff]
[    0.210449] pci 0000:00:1e.2: reg 0x14: [io  0xe8c0-0xe8ff]
[    0.210460] pci 0000:00:1e.2: reg 0x18: [mem 0xdffffa00-0xdffffbff]
[    0.210470] pci 0000:00:1e.2: reg 0x1c: [mem 0xdffff900-0xdffff9ff]
[    0.210519] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
[    0.210726] pci 0000:00:1f.0: [8086:2640] type 00 class 0x060100
[    0.210813] pci 0000:00:1f.0: address space collision: [io  0x0800-0x087f] conflicts with ACPI CPU throttle [??? 0x00000810-0x00000815 flags 0x80000000]
[    0.210821] pci 0000:00:1f.0: quirk: [io  0x0880-0x08bf] claimed by ICH6 GPIO
[    0.210826] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 0c00-0c7f
[    0.210831] pci 0000:00:1f.0: LPC Generic IO decode 2 PIO at 00e0-00ef
[    0.211031] pci 0000:00:1f.1: [8086:266f] type 00 class 0x01018a
[    0.211048] pci 0000:00:1f.1: reg 0x10: [io  0x01f0-0x01f7]
[    0.211060] pci 0000:00:1f.1: reg 0x14: [io  0x03f4-0x03f7]
[    0.211071] pci 0000:00:1f.1: reg 0x18: [io  0x0170-0x0177]
[    0.211083] pci 0000:00:1f.1: reg 0x1c: [io  0x0374-0x0377]
[    0.211094] pci 0000:00:1f.1: reg 0x20: [io  0xffa0-0xffaf]
[    0.211315] pci 0000:00:1f.2: [8086:2652] type 00 class 0x010601
[    0.211333] pci 0000:00:1f.2: reg 0x10: [io  0xfe00-0xfe07]
[    0.211344] pci 0000:00:1f.2: reg 0x14: [io  0xfe10-0xfe13]
[    0.211354] pci 0000:00:1f.2: reg 0x18: [io  0xfe20-0xfe27]
[    0.211365] pci 0000:00:1f.2: reg 0x1c: [io  0xfe30-0xfe33]
[    0.211375] pci 0000:00:1f.2: reg 0x20: [io  0xfea0-0xfeaf]
[    0.211385] pci 0000:00:1f.2: reg 0x24: [mem 0xdffffc00-0xdfffffff]
[    0.211420] pci 0000:00:1f.2: PME# supported from D3hot
[    0.211619] pci 0000:00:1f.3: [8086:266a] type 00 class 0x0c0500
[    0.211678] pci 0000:00:1f.3: reg 0x20: [io  0xe8a0-0xe8bf]
[    0.211968] pci 0000:01:00.0: [1002:5b60] type 00 class 0x030000
[    0.211984] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xd7ffffff pref]
[    0.211995] pci 0000:01:00.0: reg 0x14: [io  0xdc00-0xdcff]
[    0.212012] pci 0000:01:00.0: reg 0x18: [mem 0xdfde0000-0xdfdeffff]
[    0.212043] pci 0000:01:00.0: reg 0x30: [mem 0xdfe00000-0xdfe1ffff pref]
[    0.212083] pci 0000:01:00.0: supports D1 D2
[    0.212150] pci 0000:01:00.1: [1002:5b70] type 00 class 0x038000
[    0.212164] pci 0000:01:00.1: reg 0x10: [mem 0xdfdf0000-0xdfdfffff]
[    0.212237] pci 0000:01:00.1: supports D1 D2
[    0.212291] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.212304] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.212310] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.212315] pci 0000:00:01.0:   bridge window [mem 0xdfd00000-0xdfefffff]
[    0.212320] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd7ffffff pref]
[    0.212422] pci 0000:02:00.0: [14e4:1677] type 00 class 0x020000
[    0.212451] pci 0000:02:00.0: reg 0x10: [mem 0xdfcf0000-0xdfcfffff 64bit]
[    0.212584] pci 0000:02:00.0: PME# supported from D3hot D3cold
[    0.212649] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.212661] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.212670] pci 0000:00:1c.0:   bridge window [mem 0xdfc00000-0xdfcfffff]
[    0.212750] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.212760] pci 0000:00:1c.1:   bridge window [mem 0xdfb00000-0xdfbfffff]
[    0.212869] pci 0000:00:1e.0: PCI bridge to [bus 04] (subtractive decode)
[    0.212883] pci 0000:00:1e.0:   bridge window [io  0x0000-0xffff] (subtractive decode)
[    0.212887] pci 0000:00:1e.0:   bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
[    0.212914] pci_bus 0000:00: on NUMA node 0
[    0.223775] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[    0.224205] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[    0.224620] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
[    0.225040] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[    0.225455] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15)
[    0.225871] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15)
[    0.226284] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
[    0.226696] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[    0.226899] ACPI: Enabled 1 GPEs in block 00 to 1F
[    0.226911] ACPI: \_SB_.PCI0: notify handler is installed
[    0.226940] Found 1 acpi root devices
[    0.227042] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.227042] vgaarb: loaded
[    0.227042] vgaarb: bridge control possible 0000:01:00.0
[    0.227042] PCI: Using ACPI for IRQ routing
[    0.234313] PCI: pci_cache_line_size set to 64 bytes
[    0.234372] e820: reserve RAM buffer [mem 0xcfe8cc00-0xcfffffff]
[    0.234555] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.234561] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.234568] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.236029] Switched to clocksource hpet
[    0.239038] pnp: PnP ACPI init
[    0.239060] ACPI: bus type PNP registered
[    0.241146] pnp 00:00: disabling [io  0x0800-0x085f] because it overlaps 0000:00:1f.0 BAR 13 [io  0x0800-0x087f]
[    0.241153] pnp 00:00: disabling [io  0x0860-0x08ff] because it overlaps 0000:00:1f.0 BAR 13 [io  0x0800-0x087f]
[    0.241202] system 00:00: [io  0x0c00-0x0c7f] has been reserved
[    0.241210] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.241333] pnp 00:01: [dma 4]
[    0.241367] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.241506] pnp 00:02: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.241630] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.241763] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.244787] pnp 00:05: [dma 2]
[    0.245029] pnp 00:05: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.246170] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.249067] pnp 00:07: Plug and Play ACPI device, IDs PNP0f13 (active)
[    0.252478] pnp 00:08: [dma 0 disabled]
[    0.252989] pnp 00:08: Plug and Play ACPI device, IDs PNP0401 (active)
[    0.255550] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.265822] system 00:0a: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.265829] system 00:0a: [mem 0x00100000-0x00ffffff] could not be reserved
[    0.265834] system 00:0a: [mem 0x01000000-0xcfe8cbff] could not be reserved
[    0.265839] system 00:0a: [mem 0x000c0000-0x000fffff] could not be reserved
[    0.265843] system 00:0a: [mem 0xfec00000-0xfecfffff] could not be reserved
[    0.265847] system 00:0a: [mem 0xfee00000-0xfeefffff] has been reserved
[    0.265852] system 00:0a: [mem 0xfed20000-0xfed9ffff] has been reserved
[    0.265856] system 00:0a: [mem 0xffb00000-0xffbfffff] has been reserved
[    0.265860] system 00:0a: [mem 0xffc00000-0xffffffff] has been reserved
[    0.265865] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.266029] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
[    0.266034] system 00:0b: [mem 0xfeda0000-0xfedacfff] has been reserved
[    0.266038] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.266170] pnp 00:0c: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.266178] pnp: PnP ACPI: found 13 devices
[    0.266181] ACPI: bus type PNP unregistered
[    0.266186] PnPBIOS: Disabled by ACPI PNP
[    0.304300] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 02] add_size 1000
[    0.304308] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[    0.304319] pci 0000:00:1c.1: bridge window [io  0x1000-0x0fff] to [bus 03] add_size 1000
[    0.304324] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000
[    0.304339] pci 0000:00:1f.0: BAR 13: [io  0x0800-0x087f] has bogus alignment
[    0.304345] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.304349] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.304352] pci 0000:00:1c.0: res[13]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.304356] pci 0000:00:1c.1: res[13]=[io  0x1000-0x0fff] get_res_add_size add_size 1000
[    0.304364] pci 0000:00:1c.0: BAR 15: assigned [mem 0xd8000000-0xd81fffff 64bit pref]
[    0.304369] pci 0000:00:1c.1: BAR 15: assigned [mem 0xd8200000-0xd83fffff 64bit pref]
[    0.304375] pci 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]
[    0.304379] pci 0000:00:1c.1: BAR 13: assigned [io  0x2000-0x2fff]
[    0.304384] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.304389] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.304395] pci 0000:00:01.0:   bridge window [mem 0xdfd00000-0xdfefffff]
[    0.304400] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xd7ffffff pref]
[    0.304406] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.304411] pci 0000:00:1c.0:   bridge window [io  0x1000-0x1fff]
[    0.304417] pci 0000:00:1c.0:   bridge window [mem 0xdfc00000-0xdfcfffff]
[    0.304423] pci 0000:00:1c.0:   bridge window [mem 0xd8000000-0xd81fffff 64bit pref]
[    0.304430] pci 0000:00:1c.1: PCI bridge to [bus 03]
[    0.304434] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.304440] pci 0000:00:1c.1:   bridge window [mem 0xdfb00000-0xdfbfffff]
[    0.304446] pci 0000:00:1c.1:   bridge window [mem 0xd8200000-0xd83fffff 64bit pref]
[    0.304453] pci 0000:00:1e.0: PCI bridge to [bus 04]
[    0.304467] pci_bus 0000:00: resource 4 [io  0x0000-0xffff]
[    0.304471] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
[    0.304474] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.304477] pci_bus 0000:01: resource 1 [mem 0xdfd00000-0xdfefffff]
[    0.304481] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xd7ffffff pref]
[    0.304484] pci_bus 0000:02: resource 0 [io  0x1000-0x1fff]
[    0.304487] pci_bus 0000:02: resource 1 [mem 0xdfc00000-0xdfcfffff]
[    0.304491] pci_bus 0000:02: resource 2 [mem 0xd8000000-0xd81fffff 64bit pref]
[    0.304494] pci_bus 0000:03: resource 0 [io  0x2000-0x2fff]
[    0.304497] pci_bus 0000:03: resource 1 [mem 0xdfb00000-0xdfbfffff]
[    0.304500] pci_bus 0000:03: resource 2 [mem 0xd8200000-0xd83fffff 64bit pref]
[    0.304504] pci_bus 0000:04: resource 4 [io  0x0000-0xffff]
[    0.304507] pci_bus 0000:04: resource 5 [mem 0x00000000-0xfffffffff]
[    0.304580] NET: Registered protocol family 2
[    0.304838] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.304875] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.304909] TCP: Hash tables configured (established 8192 bind 8192)
[    0.304948] TCP: reno registered
[    0.304953] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.304962] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.305071] NET: Registered protocol family 1
[    0.307283] pci 0000:01:00.0: Boot video device
[    0.307293] PCI: CLS 64 bytes, default 64
[    0.307355] Unpacking initramfs...
[    0.693054] Freeing initrd memory: 12740K (f670e000 - f737f000)
[    0.693117] Simple Boot Flag at 0x7a set to 0x1
[    0.693266] microcode: CPU0 sig=0xf34, pf=0x10, revision=0x17
[    0.693279] microcode: CPU1 sig=0xf34, pf=0x10, revision=0x17
[    0.693369] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.693857] audit: initializing netlink socket (disabled)
[    0.693874] type=2000 audit(1392407445.692:1): initialized
[    0.710093] bounce pool size: 64 pages
[    0.710101] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.710645] VFS: Disk quotas dquot_6.5.2
[    0.710687] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.710816] msgmni has been set to 1710
[    0.711253] alg: No test for stdrng (krng)
[    0.711291] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.711351] io scheduler noop registered
[    0.711356] io scheduler deadline registered
[    0.711374] io scheduler cfq registered (default)
[    0.711742] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[    0.712059] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[    0.712363] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[    0.712472] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.712500] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.712574] GHES: HEST is not enabled!
[    0.712593] isapnp: Scanning for PnP cards...
[    1.065755] isapnp: No Plug & Play device found
[    1.065849] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.086346] 00:09: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.086965] Linux agpgart interface v0.103
[    1.087232] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[    1.090222] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.090232] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.090434] mousedev: PS/2 mouse device common for all mice
[    1.090505] rtc_cmos 00:04: RTC can wake from S4
[    1.090658] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    1.090688] rtc_cmos 00:04: alarms up to one day, 242 bytes nvram, hpet irqs
[    1.090810] TCP: cubic registered
[    1.090862] NET: Registered protocol family 10
[    1.091143] mip6: Mobile IPv6
[    1.091147] NET: Registered protocol family 17
[    1.091153] mpls_gso: MPLS GSO support
[    1.091340] Using IPI No-Shortcut mode
[    1.091517] registered taskstats version 1
[    1.092222] rtc_cmos 00:04: setting system clock to 2014-02-14 19:50:46 UTC (1392407446)
[    1.092291] PM: Hibernation image not present or could not be loaded.
[    1.092619] Freeing unused kernel memory: 520K (c15a5000 - c1627000)
[    1.092649] Write protecting the kernel text: 4136k
[    1.092709] Write protecting the kernel read-only data: 1268k
[    1.111849] systemd-udevd[56]: starting version 204
[    1.125316] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.158957] ACPI: bus type USB registered
[    1.159022] usbcore: registered new interface driver usbfs
[    1.159054] usbcore: registered new interface driver hub
[    1.162430] usbcore: registered new device driver usb
[    1.163243] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.163796] uhci_hcd: USB Universal Host Controller Interface driver
[    1.164747] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    1.164757] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.164772] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.164835] uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ff80
[    1.164894] ehci-pci: EHCI PCI platform driver
[    1.164957] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.164964] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.164969] usb usb1: Product: UHCI Host Controller
[    1.164975] usb usb1: Manufacturer: Linux 3.12-1-686-pae uhci_hcd
[    1.164981] usb usb1: SerialNumber: 0000:00:1d.0
[    1.165231] hub 1-0:1.0: USB hub found
[    1.165248] hub 1-0:1.0: 2 ports detected
[    1.165998] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    1.166010] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.166026] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    1.166085] uhci_hcd 0000:00:1d.1: irq 22, io base 0x0000ff60
[    1.166200] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.166207] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.166213] usb usb2: Product: UHCI Host Controller
[    1.166218] usb usb2: Manufacturer: Linux 3.12-1-686-pae uhci_hcd
[    1.166223] usb usb2: SerialNumber: 0000:00:1d.1
[    1.167022] hub 2-0:1.0: USB hub found
[    1.167043] hub 2-0:1.0: 2 ports detected
[    1.167756] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    1.167765] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.167778] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    1.167837] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
[    1.167958] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.167965] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.167971] usb usb3: Product: UHCI Host Controller
[    1.167976] usb usb3: Manufacturer: Linux 3.12-1-686-pae uhci_hcd
[    1.167981] usb usb3: SerialNumber: 0000:00:1d.2
[    1.168267] hub 3-0:1.0: USB hub found
[    1.168283] hub 3-0:1.0: 2 ports detected
[    1.169965] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    1.169974] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    1.169989] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    1.170049] uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ff20
[    1.170149] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.170155] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.170160] usb usb4: Product: UHCI Host Controller
[    1.170165] usb usb4: Manufacturer: Linux 3.12-1-686-pae uhci_hcd
[    1.170169] usb usb4: SerialNumber: 0000:00:1d.3
[    1.170398] hub 4-0:1.0: USB hub found
[    1.170415] hub 4-0:1.0: 2 ports detected
[    1.171579] ehci-pci 0000:00:1d.7: setting latency timer to 64
[    1.172518] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    1.172536] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    1.172560] ehci-pci 0000:00:1d.7: debug port 1
[    1.176497] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    1.188986] ehci-pci 0000:00:1d.7: irq 21, io mem 0xffa80800
[    1.200118] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.200218] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    1.200227] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.200234] usb usb5: Product: EHCI Host Controller
[    1.200239] usb usb5: Manufacturer: Linux 3.12-1-686-pae ehci_hcd
[    1.200245] usb usb5: SerialNumber: 0000:00:1d.7
[    1.200486] hub 5-0:1.0: USB hub found
[    1.200503] hub 5-0:1.0: 8 ports detected
[    1.205100] Floppy drive(s): fd0 is 1.44M
[    1.211202] pps_core: LinuxPPS API ver. 1 registered
[    1.211209] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.211636] PTP clock support registered
[    1.216826] tg3.c:v3.133 (Jul 29, 2013)
[    1.222054] FDC 0 is a post-1991 82077
[    1.224195] hub 1-0:1.0: USB hub found
[    1.224215] hub 1-0:1.0: 2 ports detected
[    1.233366] SCSI subsystem initialized
[    1.246130] tg3 0000:02:00.0 eth0: Tigon3 [partno(BCM95751) rev 4001] (PCI Express) MAC address 00:11:11:30:6b:94
[    1.246140] tg3 0000:02:00.0 eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    1.246147] tg3 0000:02:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    1.246154] tg3 0000:02:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    1.248143] hub 2-0:1.0: USB hub found
[    1.248166] hub 2-0:1.0: 2 ports detected
[    1.251846] libata version 3.00 loaded.
[    1.272339] hub 3-0:1.0: USB hub found
[    1.272364] hub 3-0:1.0: 2 ports detected
[    1.296132] hub 4-0:1.0: USB hub found
[    1.296156] hub 4-0:1.0: 2 ports detected
[    1.296703] ahci 0000:00:1f.2: version 3.0
[    1.297081] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0xf impl SATA mode
[    1.297087] ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part
[    1.297093] ahci 0000:00:1f.2: setting latency timer to 64
[    1.300119] scsi0 : ahci
[    1.301190] scsi1 : ahci
[    1.301510] scsi2 : ahci
[    1.302158] scsi3 : ahci
[    1.302286] ata1: SATA max UDMA/133 abar m1024@0xdffffc00 port 0xdffffd00 irq 20
[    1.302293] ata2: SATA max UDMA/133 abar m1024@0xdffffc00 port 0xdffffd80 irq 20
[    1.302299] ata3: SATA max UDMA/133 abar m1024@0xdffffc00 port 0xdffffe00 irq 20
[    1.302305] ata4: SATA max UDMA/133 abar m1024@0xdffffc00 port 0xdffffe80 irq 20
[    1.302349] ata_piix 0000:00:1f.1: version 2.13
[    1.302766] ata_piix 0000:00:1f.1: setting latency timer to 64
[    1.305043] scsi4 : ata_piix
[    1.305214] scsi5 : ata_piix
[    1.305314] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    1.305320] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    1.305706] ata6: port disabled--ignoring
[    1.476313] ata5.00: ATAPI: SAMSUNG CD-R/RW SW-252S, R902, max UDMA/33
[    1.476322] ata5.01: ATAPI: PHILIPS DVD+RW DVD8601, KD10, max UDMA/33
[    1.492195] ata5.00: configured for UDMA/33
[    1.508430] ata5.01: configured for UDMA/33
[    1.620039] ata4: SATA link down (SStatus 0 SControl 300)
[    1.620062] ata3: SATA link down (SStatus 0 SControl 300)
[    1.620085] ata2: SATA link down (SStatus 0 SControl 300)
[    1.692021] tsc: Refined TSC clocksource calibration: 2992.499 MHz
[    1.900032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.904281] ata1.00: ATA-6: WDC WD1600JD-75HBB0, 08.02D08, max UDMA/133
[    1.904286] ata1.00: 312500000 sectors, multi 8: LBA48
[    1.909863] ata1.00: configured for UDMA/133
[    1.910038] scsi 0:0:0:0: Direct-Access     ATA      WDC WD1600JD-75H 08.0 PQ: 0 ANSI: 5
[    1.911286] scsi 4:0:0:0: CD-ROM            SAMSUNG  CD-R/RW SW-252S  R902 PQ: 0 ANSI: 5
[    1.913642] scsi 4:0:1:0: CD-ROM            PHILIPS  DVD+RW DVD8601   KD10 PQ: 0 ANSI: 5
[    1.927825] sr0: scsi3-mmc drive: 48x/16x writer cd/rw xa/form2 cdda tray
[    1.927837] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.928312] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    1.930204] sd 0:0:0:0: [sda] 312500000 512-byte logical blocks: (160 GB/149 GiB)
[    1.930368] sd 0:0:0:0: [sda] Write Protect is off
[    1.930377] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.930428] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.932600] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[    1.932811] sr 4:0:1:0: Attached scsi CD-ROM sr1
[    1.936816] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.936908] sr 4:0:0:0: Attached scsi generic sg1 type 5
[    1.936992] sr 4:0:1:0: Attached scsi generic sg2 type 5
[    2.027122]  sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
[    2.028085] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.692114] Switched to clocksource tsc
[    2.851672] PM: Starting manual resume from disk
[    2.851678] PM: Hibernation image partition 8:7 present
[    2.851681] PM: Looking for hibernation image.
[    2.851857] PM: Image not found (code -22)
[    2.851861] PM: Hibernation image not present or could not be loaded.
[    2.875934] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    3.781385] systemd-udevd[334]: starting version 204
[    4.279927] intel_rng: Firmware space is locked read-only. If you can't or
[    4.279927] intel_rng: don't want to disable this in firmware setup, and if
[    4.279927] intel_rng: you are certain that your system has a functional
[    4.279927] intel_rng: RNG, try using the 'no_fwh_detect' option.
[    4.281997] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[    4.282010] ACPI: Power Button [VBTN]
[    4.282135] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    4.282144] ACPI: Power Button [PWRF]
[    4.282730] parport_pc 00:08: reported by Plug and Play ACPI
[    4.282789] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[    4.426097] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
[    4.443732] [drm] Initialized drm 1.1.0 20060810
[    4.526694] input: PC Speaker as /devices/platform/pcspkr/input/input5
[    4.563715] ACPI Warning: 0x00000828-0x0000082f SystemIO conflicts with Region \GLBC 1 (20130725/utaddress-251)
[    4.563728] ACPI Warning: 0x00000828-0x0000082f SystemIO conflicts with Region \SACT 2 (20130725/utaddress-251)
[    4.563736] ACPI Warning: 0x00000828-0x0000082f SystemIO conflicts with Region \SSTS 3 (20130725/utaddress-251)
[    4.563745] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    4.563805] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    4.834554] psmouse serio1: alps: Unknown ALPS touchpad: E7=10 00 64, EC=10 00 64
[    4.839902] [drm] radeon kernel modesetting enabled.
[    4.841140] [drm] initializing kernel modesetting (RV380 0x1002:0x5B60 0x1002:0x0302).
[    4.841173] [drm] register mmio base: 0xDFDE0000
[    4.841179] [drm] register mmio size: 65536
[    4.841294] [drm] Generation 2 PCI interface, using max accessible memory
[    4.841305] radeon 0000:01:00.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (128M used)
[    4.841311] radeon 0000:01:00.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
[    4.841327] [drm] Detected VRAM RAM=128M, BAR=128M
[    4.841332] [drm] RAM width 64bits DDR
[    4.841412] [TTM] Zone  kernel: Available graphics memory: 438258 kiB
[    4.841416] [TTM] Zone highmem: Available graphics memory: 1685774 kiB
[    4.841419] [TTM] Initializing pool allocator
[    4.841430] [TTM] Initializing DMA pool allocator
[    4.841471] [drm] radeon: 128M of VRAM memory ready
[    4.841476] [drm] radeon: 512M of GTT memory ready.
[    4.841505] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    4.843069] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[    4.845667] [drm] PCIE GART of 512M enabled (table at 0x00000000D0040000).
[    4.845710] radeon 0000:01:00.0: WB enabled
[    4.845719] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffb0d000
[    4.845730] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    4.845734] [drm] Driver supports precise vblank timestamp query.
[    4.845774] radeon 0000:01:00.0: irq 43 for MSI/MSI-X
[    4.845798] radeon 0000:01:00.0: radeon: using MSI.
[    4.845836] [drm] radeon: irq initialized.
[    4.845857] [drm] Loading R300 Microcode
[    4.847937] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[    4.874675] iTCO_vendor_support: vendor-support=0
[    4.875395] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[    4.875444] iTCO_wdt: Found a ICH6 or ICH6R TCO device (Version=2, TCOBASE=0x0860)
[    4.875624] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    5.095883] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/R300_cp.bin
[    5.096128] [drm] radeon: ring at 0x00000000B0001000
[    5.096154] [drm] ring test succeeded in 1 usecs
[    5.096319] [drm] ib test succeeded in 0 usecs
[    5.096749] [drm] Radeon Display Connectors
[    5.096754] [drm] Connector 0:
[    5.096758] [drm]   VGA-1
[    5.096763] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[    5.096767] [drm]   Encoders:
[    5.096770] [drm]     CRT1: INTERNAL_DAC1
[    5.096774] [drm] Connector 1:
[    5.096778] [drm]   DVI-I-1
[    5.096781] [drm]   HPD1
[    5.096785] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[    5.096788] [drm]   Encoders:
[    5.096791] [drm]     CRT2: INTERNAL_DAC2
[    5.096795] [drm]     DFP1: INTERNAL_TMDS1
[    5.096798] [drm] Connector 2:
[    5.096802] [drm]   SVIDEO-1
[    5.096804] [drm]   Encoders:
[    5.096808] [drm]     TV1: INTERNAL_DAC2
[    5.110353] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[    5.124954] [drm] fb mappable at 0xD00C0000
[    5.124959] [drm] vram apper at 0xD0000000
[    5.124962] [drm] size 3145728
[    5.124964] [drm] fb depth is 24
[    5.124966] [drm]    pitch is 4096
[    5.125086] fbcon: radeondrmfb (fb0) is primary device
[    5.179506] Console: switching to colour frame buffer device 128x48
[    5.182886] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[    5.182890] radeon 0000:01:00.0: registered panic notifier
[    5.182898] [drm] Initialized radeon 2.34.0 20080528 for 0000:01:00.0 on minor 0
[    5.479556] intel8x0: white list rate for 1028:0177 is 48000
[    5.486731] udevd[450]: failed to execute '/usr/sbin/alsactl' '/usr/sbin/alsactl -E HOME=/var/run/alsa restore ': No such file or directory
[    5.503638] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[    6.241385] Adding 6655996k swap on /dev/sda7.  Priority:-1 extents:1 across:6655996k
[    6.252096] EXT4-fs (sda1): re-mounted. Opts: (null)
[    6.877852] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    8.416542] fuse init (API version 7.22)
[    8.931076] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[    8.975519] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
[    9.030269] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[    9.116379] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[   10.789989] RPC: Registered named UNIX socket transport module.
[   10.789995] RPC: Registered udp transport module.
[   10.789997] RPC: Registered tcp transport module.
[   10.790000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   10.820524] FS-Cache: Loaded
[   10.849088] FS-Cache: Netfs 'nfs' registered for caching
[   10.892194] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   13.196778] lp0: using parport0 (interrupt-driven).
[   13.347351] ppdev: user-space parallel port driver
[   15.770558] Bluetooth: Core ver 2.16
[   15.770595] NET: Registered protocol family 31
[   15.770599] Bluetooth: HCI device and connection manager initialized
[   15.770614] Bluetooth: HCI socket layer initialized
[   15.770621] Bluetooth: L2CAP socket layer initialized
[   15.770636] Bluetooth: SCO socket layer initialized
[   15.806099] Bluetooth: RFCOMM TTY layer initialized
[   15.806120] Bluetooth: RFCOMM socket layer initialized
[   15.806124] Bluetooth: RFCOMM ver 1.11
[   15.868680] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.868688] Bluetooth: BNEP filters: protocol multicast
[   15.868701] Bluetooth: BNEP socket layer initialized
Debian&Me
 
Posts: 3
Joined: 2014-02-15 00:44

Re: Lockups occur after installation of firmware-linux-nonfr

Postby Debian&Me » 2014-02-15 01:59

other info:
Code: Select all
root@Dimension:/home/paul# /usr/share/bug/xserver-xorg-video-radeon/script 3>&1
X server symlink status:
------------------------
lrwxrwxrwx 1 root root 13 Jan 30 18:56 /etc/X11/X -> /usr/bin/Xorg
-rwxr-xr-x 1 root root 2273512 Dec 13 03:50 /usr/bin/Xorg

VGA-compatible devices on PCI bus:
----------------------------------
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV370 [Radeon X300] [1002:5b60]

/etc/X11/xorg.conf does not exist.

/etc/X11/xorg.conf.d does not exist.

/etc/modprobe.d contains no KMS configuration files.

Kernel version (/proc/version):
-------------------------------
Linux version 3.12-1-686-pae (debian-kernel@lists.debian.org) (gcc version 4.8.2 (Debian 4.8.2-14) ) #1 SMP Debian 3.12.9-1 (2014-02-01)

Xorg X server log files on system:
----------------------------------
-rw-r--r-- 1 root root 19236 Feb 13 23:43 /var/log/Xorg.1.log
-rw-r--r-- 1 root root 19236 Feb 13 23:43 /var/log/Xorg.2.log
-rw-r--r-- 1 root root 19236 Feb 13 23:43 /var/log/Xorg.3.log
-rw-r--r-- 1 root root 19236 Feb 13 23:43 /var/log/Xorg.4.log
-rw-r--r-- 1 root root 19236 Feb 13 23:43 /var/log/Xorg.5.log
-rw-r--r-- 1 root root 29941 Feb 14 13:39 /var/log/Xorg.0.log

Contents of most recent Xorg X server log file (/var/log/Xorg.0.log):
---------------------------------------------------------------------
[    17.587]
X.Org X Server 1.14.5
Release Date: 2013-12-12
[    17.587] X Protocol Version 11, Revision 0
[    17.587] Build Operating System: Linux 3.2.0-4-amd64 i686 Debian
[    17.587] Current Operating System: Linux Dimension 3.12-1-686-pae #1 SMP Debian 3.12.9-1 (2014-02-01) i686
[    17.587] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.12-1-686-pae root=UUID=47f196f6-9813-454b-83fb-44ce953e4f0c ro quiet
[    17.587] Build Date: 13 December 2013  10:45:09AM
[    17.587] xorg-server 2:1.14.5-1 (Maarten Lankhorst <maarten.lankhorst@ubuntu.com>)
[    17.587] Current version of pixman: 0.32.4
[    17.587]    Before reporting problems, check http://wiki.x.org
   to make sure that you have the latest version.
[    17.587] Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    17.587] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Feb 14 13:36:00 2014
[    17.712] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    17.811] (==) No Layout section.  Using the first Screen section.
[    17.812] (**) |-->Screen "Default Screen" (0)
[    17.812] (**) |   |-->Monitor "NANAO FlexScan T2-17"
[    17.812] (**) |   |-->Device "ATI Radeon X300 [RV370] 5B60 (PCIE)"
[    17.812] (==) Automatically adding devices
[    17.812] (==) Automatically enabling devices
[    17.812] (==) Automatically adding GPU devices
[    17.845] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    17.845]    Entry deleted from font path.
[    17.846] (==) FontPath set to:
   /usr/share/fonts/X11/misc,
   /usr/share/fonts/X11/100dpi/:unscaled,
   /usr/share/fonts/X11/75dpi/:unscaled,
   /usr/share/fonts/X11/Type1,
   /usr/share/fonts/X11/100dpi,
   /usr/share/fonts/X11/75dpi,
   built-ins
[    17.846] (==) ModulePath set to "/usr/lib/xorg/modules"
[    17.846] (II) The server relies on udev to provide the list of input devices.
   If no devices become available, reconfigure udev or disable AutoAddDevices.
[    17.846] (II) Loader magic: 0xb77e86a0
[    17.846] (II) Module ABI versions:
[    17.846]    X.Org ANSI C Emulation: 0.4
[    17.846]    X.Org Video Driver: 14.1
[    17.846]    X.Org XInput driver : 19.1
[    17.846]    X.Org Server Extension : 7.0
[    17.846] (II) xfree86: Adding drm device (/dev/dri/card0)
[    17.848] (--) PCI:*(0:1:0:0) 1002:5b60:1002:0302 rev 0, Mem @ 0xd0000000/134217728, 0xdfde0000/65536, I/O @ 0x0000dc00/256, BIOS @ 0x????????/131072
[    17.848] (--) PCI: (0:1:0:1) 1002:5b70:1002:0303 rev 0, Mem @ 0xdfdf0000/65536
[    17.849] (II) Open ACPI successful (/var/run/acpid.socket)
[    17.862] Initializing built-in extension Generic Event Extension
[    17.862] Initializing built-in extension SHAPE
[    17.862] Initializing built-in extension MIT-SHM
[    17.862] Initializing built-in extension XInputExtension
[    17.863] Initializing built-in extension XTEST
[    17.863] Initializing built-in extension BIG-REQUESTS
[    17.863] Initializing built-in extension SYNC
[    17.863] Initializing built-in extension XKEYBOARD
[    17.863] Initializing built-in extension XC-MISC
[    17.863] Initializing built-in extension SECURITY
[    17.863] Initializing built-in extension XINERAMA
[    17.863] Initializing built-in extension XFIXES
[    17.863] Initializing built-in extension RENDER
[    17.863] Initializing built-in extension RANDR
[    17.863] Initializing built-in extension COMPOSITE
[    17.863] Initializing built-in extension DAMAGE
[    17.863] Initializing built-in extension MIT-SCREEN-SAVER
[    17.863] Initializing built-in extension DOUBLE-BUFFER
[    17.863] Initializing built-in extension RECORD
[    17.863] Initializing built-in extension DPMS
[    17.863] Initializing built-in extension X-Resource
[    17.863] Initializing built-in extension XVideo
[    17.863] Initializing built-in extension XVideo-MotionCompensation
[    17.863] Initializing built-in extension SELinux
[    17.863] Initializing built-in extension XFree86-VidModeExtension
[    17.863] Initializing built-in extension XFree86-DGA
[    17.863] Initializing built-in extension XFree86-DRI
[    17.863] Initializing built-in extension DRI2
[    17.863] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[    17.863] (II) LoadModule: "glx"
[    17.872] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    17.897] (II) Module glx: vendor="X.Org Foundation"
[    17.897]    compiled for 1.14.5, module version = 1.0.0
[    17.898]    ABI class: X.Org Server Extension, version 7.0
[    17.898] (==) AIGLX enabled
[    17.898] Loading extension GLX
[    17.898] (II) LoadModule: "radeon"
[    17.899] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
[    18.071] (II) Module radeon: vendor="X.Org Foundation"
[    18.071]    compiled for 1.14.5, module version = 7.3.0
[    18.071]    Module class: X.Org Video Driver
[    18.071]    ABI class: X.Org Video Driver, version 14.1
[    18.071] (II) RADEON: Driver for ATI Radeon chipsets:
   ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
   ATI Radeon Mobility X300 (M24) 3152 (PCIE),
   ATI FireGL M24 GL 3154 (PCIE), ATI FireMV 2400 3155 (PCI),
   ATI Radeon X600 (RV380) 3E50 (PCIE),
   ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
   ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
   ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
   ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
   ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
   ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
   ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
   ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
   ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
   ATI Radeon 8500 AIW BB (AGP), ATI Radeon IGP320M (U1) 4336,
   ATI Radeon IGP330M/340M/350M (U2) 4337,
   ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
   ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
   ATI Radeon X800PRO (R420) JI (AGP),
   ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
   ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
   ATI Radeon Mobility 9800 (M18) JN (AGP),
   ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
   ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
   ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
   ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
   ATI Radeon Mobility M7 LW (AGP),
   ATI Mobility FireGL 7800 M7 LX (AGP),
   ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
   ATI FireGL Mobility 9000 (M9) Ld (AGP),
   ATI Radeon Mobility 9000 (M9) Lf (AGP),
   ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI FireMV 2400 PCI,
   ATI Radeon 9700 Pro ND (AGP), ATI Radeon 9700/9500Pro NE (AGP),
   ATI Radeon 9600TX NF (AGP), ATI FireGL X1 NG (AGP),
   ATI Radeon 9800PRO NH (AGP), ATI Radeon 9800 NI (AGP),
   ATI FireGL X2 NK (AGP), ATI Radeon 9800XT NJ (AGP),
   ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
   ATI Radeon Mobility 9600 (M10) NQ (AGP),
   ATI Radeon Mobility 9600 (M11) NR (AGP),
   ATI Radeon Mobility 9600 (M10) NS (AGP),
   ATI FireGL Mobility T2 (M10) NT (AGP),
   ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
   ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
   ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
   ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
   ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
   ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
   ATI Radeon Mobility X300 (M22) 5460 (PCIE),
   ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
   ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
   ATI Radeon X800PRO (R423) UI (PCIE),
   ATI Radeon X800LE (R423) UJ (PCIE),
   ATI Radeon X800SE (R423) UK (PCIE),
   ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
   ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
   ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
   ATI FireGL unknown (R423) UR (PCIE),
   ATI FireGL unknown (R423) UT (PCIE),
   ATI Mobility FireGL V5000 (M26) (PCIE),
   ATI Mobility FireGL V5000 (M26) (PCIE),
   ATI Mobility Radeon X700 XL (M26) (PCIE),
   ATI Mobility Radeon X700 (M26) (PCIE),
   ATI Mobility Radeon X700 (M26) (PCIE),
   ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
   ATI Radeon Mobility 9100 IGP (U3) 5835,
   ATI Radeon XPRESS 200 5954 (PCIE),
   ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
   ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
   ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
   ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
   ATI Radeon XPRESS 200M 5975 (PCIE),
   ATI Radeon XPRESS 200 5A41 (PCIE),
   ATI Radeon XPRESS 200M 5A42 (PCIE),
   ATI Radeon XPRESS 200 5A61 (PCIE),
   ATI Radeon XPRESS 200M 5A62 (PCIE),
   ATI Radeon X300 (RV370) 5B60 (PCIE),
   ATI Radeon X600 (RV370) 5B62 (PCIE),
   ATI Radeon X550 (RV370) 5B63 (PCIE),
   ATI FireGL V3100 (RV370) 5B64 (PCIE),
   ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
   ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
   ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
   ATI Mobility Radeon X800 XT (M28) (PCIE),
   ATI Mobility FireGL V5100 (M28) (PCIE),
   ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
   ATI Radeon X850 XT PE (R480) (PCIE),
   ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
   ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
   ATI Radeon X850 XT (R480) (PCIE),
   ATI Radeon X800XT (R423) 5D57 (PCIE),
   ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
   ATI Radeon X700 PRO (RV410) (PCIE),
   ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
   ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
   ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
   ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
   ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
   ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
   ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
   ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
   ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
   ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
   ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
   ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
   ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
   ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
   ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
   ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
   ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
   ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
   ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
   ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
   ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
   ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
   ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
   ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
   ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
   ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
   ATI Mobility Radeon X1700, ATI Radeon X2300HD,
   ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
   ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
   ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
   ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
   ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
   ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
   ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
   ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
   ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
   ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
   ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
   ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
   ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
   ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
   ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
   ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
   ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
   ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
   ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
   ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
   AMD FireStream 9250, ATI FirePro V8700 (FireGL),
   ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
   ATI Mobility RADEON HD 4870, ATI Radeon 4800 Series,
   ATI Radeon 4800 Series, ATI FirePro M7750, ATI M98, ATI M98, ATI M98,
   ATI Mobility Radeon HD 4650, ATI Radeon RV730 (AGP),
   ATI Mobility Radeon HD 4670, ATI FirePro M5750,
   ATI Mobility Radeon HD 4670, ATI Radeon RV730 (AGP),
   ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
   ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
   ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
   ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
   ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
   ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
   ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
   ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
   ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
   ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
   ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
   ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
   ATI Mobility Radeon HD 3850 X2, ATI RV670,
   ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
   ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
   ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
   ATI Radeon RV710, ATI Radeon RV710, ATI Radeon RV710,
   ATI Radeon HD 4350, ATI Mobility Radeon 4300 Series,
   ATI Mobility Radeon 4500 Series, ATI Mobility Radeon 4500 Series,
   ATI FirePro RG220, ATI Mobility Radeon 4330, ATI RV630,
   ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
   ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
   ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
   ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
   ATI FireGL V3600, ATI Radeon HD 2600 LE,
   ATI Mobility FireGL Graphics Processor, ATI Radeon HD 3470,
   ATI Mobility Radeon HD 3430, ATI Mobility Radeon HD 3400 Series,
   ATI Radeon HD 3450, ATI Radeon HD 3450, ATI Radeon HD 3430,
   ATI Radeon HD 3450, ATI FirePro V3700, ATI FireMV 2450,
   ATI FireMV 2260, ATI FireMV 2260, ATI Radeon HD 3600 Series,
   ATI Radeon HD 3650 AGP, ATI Radeon HD 3600 PRO,
   ATI Radeon HD 3600 XT, ATI Radeon HD 3600 PRO,
   ATI Mobility Radeon HD 3650, ATI Mobility Radeon HD 3670,
   ATI Mobility FireGL V5700, ATI Mobility FireGL V5725,
   ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
   ATI Radeon HD 3200 Graphics, ATI Radeon 3100 Graphics,
   ATI Radeon HD 3300 Graphics, ATI Radeon HD 3200 Graphics,
   ATI Radeon 3000 Graphics, SUMO, SUMO, SUMO2, SUMO2, SUMO2, SUMO2,
   SUMO, SUMO, SUMO2, SUMO, SUMO, SUMO, SUMO, SUMO, ATI Radeon HD 4200,
   ATI Radeon 4100, ATI Mobility Radeon HD 4200,
   ATI Mobility Radeon 4100, ATI Radeon HD 4290, ATI Radeon HD 4250,
   AMD Radeon HD 6310 Graphics, AMD Radeon HD 6310 Graphics,
   AMD Radeon HD 6250 Graphics, AMD Radeon HD 6250 Graphics,
   AMD Radeon HD 6300 Series Graphics,
   AMD Radeon HD 6200 Series Graphics, PALM, PALM, PALM, CYPRESS,
   ATI FirePro (FireGL) Graphics Adapter,
   ATI FirePro (FireGL) Graphics Adapter,
   ATI FirePro (FireGL) Graphics Adapter, AMD Firestream 9370,
   AMD Firestream 9350, ATI Radeon HD 5800 Series,
   ATI Radeon HD 5800 Series, ATI Radeon HD 5800 Series,
   ATI Radeon HD 5800 Series, ATI Radeon HD 5900 Series,
   ATI Radeon HD 5900 Series, ATI Mobility Radeon HD 5800 Series,
   ATI Mobility Radeon HD 5800 Series,
   ATI FirePro (FireGL) Graphics Adapter,
   ATI FirePro (FireGL) Graphics Adapter,
   ATI Mobility Radeon HD 5800 Series, ATI Radeon HD 5700 Series,
   ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
   ATI Radeon HD 5700 Series, ATI Radeon HD 6700 Series,
   ATI Mobility Radeon HD 5000 Series,
   ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon HD 5570,
   ATI FirePro (FireGL) Graphics Adapter,
   ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5670,
   ATI Radeon HD 5570, ATI Radeon HD 5500 Series, REDWOOD,
   ATI Mobility Radeon HD 5000 Series,
   ATI Mobility Radeon HD 5000 Series, ATI Mobility Radeon Graphics,
   ATI Mobility Radeon Graphics, CEDAR,
   ATI FirePro (FireGL) Graphics Adapter,
   ATI FirePro (FireGL) Graphics Adapter, ATI FirePro 2270, CEDAR,
   ATI Radeon HD 5450, CEDAR, CEDAR, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
   CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN, CAYMAN,
   AMD Radeon HD 6900 Series, AMD Radeon HD 6900 Series, CAYMAN, CAYMAN,
   CAYMAN, AMD Radeon HD 6900M Series, Mobility Radeon HD 6000 Series,
   BARTS, BARTS, Mobility Radeon HD 6000 Series,
   Mobility Radeon HD 6000 Series, BARTS, BARTS, BARTS, BARTS,
   AMD Radeon HD 6800 Series, AMD Radeon HD 6800 Series,
   AMD Radeon HD 6700 Series, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
   TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
   TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS, TURKS,
   CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS,
   CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, CAICOS, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, ARUBA,
   ARUBA, ARUBA, ARUBA, ARUBA, ARUBA, TAHITI, TAHITI, TAHITI, TAHITI,
   TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI, TAHITI,
   TAHITI, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN,
   PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN, PITCAIRN,
   VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE,
   VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE, VERDE,
   VERDE, VERDE, VERDE, OLAND, OLAND, OLAND, OLAND, OLAND, OLAND, OLAND,
   OLAND, OLAND, OLAND, OLAND, OLAND, OLAND, HAINAN, HAINAN, HAINAN,
   HAINAN, HAINAN, HAINAN, BONAIRE, BONAIRE, BONAIRE, BONAIRE, BONAIRE,
   BONAIRE, BONAIRE, BONAIRE, KABINI, KABINI, KABINI, KABINI, KABINI,
   KABINI, KABINI, KABINI, KABINI, KABINI, KABINI, KABINI, KABINI,
   KABINI, KABINI, KABINI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
   KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
   KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI, KAVERI,
   HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII, HAWAII,
   HAWAII, HAWAII, HAWAII, HAWAII
[    18.112] (++) using VT number 7

[    18.153] (II) [KMS] Kernel modesetting enabled.
[    18.153] (==) RADEON(0): Depth 24, (--) framebuffer bpp 32
[    18.153] (II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[    18.154] (==) RADEON(0): Default visual is TrueColor
[    18.154] (**) RADEON(0): Option "RenderAccel" "False"
[    18.154] (==) RADEON(0): RGB weight 888
[    18.154] (II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
[    18.154] (--) RADEON(0): Chipset: "ATI Radeon X300 (RV370) 5B60 (PCIE)" (ChipID = 0x5b60)
[    18.154] (II) Loading sub module "dri2"
[    18.154] (II) LoadModule: "dri2"
[    18.154] (II) Module "dri2" already built-in
[    18.154] (II) Loading sub module "exa"
[    18.154] (II) LoadModule: "exa"
[    18.154] (II) Loading /usr/lib/xorg/modules/libexa.so
[    18.162] (II) Module exa: vendor="X.Org Foundation"
[    18.162]    compiled for 1.14.5, module version = 2.6.0
[    18.162]    ABI class: X.Org Video Driver, version 14.1
[    18.162] (II) RADEON(0): KMS Color Tiling: enabled
[    18.162] (II) RADEON(0): KMS Color Tiling 2D: disabled
[    18.162] (II) RADEON(0): KMS Pageflipping: enabled
[    18.162] (II) RADEON(0): SwapBuffers wait for vsync: enabled
[    18.166] (II) RADEON(0): Output VGA-0 using monitor section NANAO FlexScan T2-17
[    18.188] (II) RADEON(0): Output DVI-0 has no monitor section
[    18.208] (II) RADEON(0): Output S-video has no monitor section
[    18.213] (II) RADEON(0): EDID for output VGA-0
[    18.213] (II) RADEON(0): Printing probed modes for output VGA-0
[    18.213] (II) RADEON(0): Modeline "1280x1024_75.00"x75.0  138.54  1280 1368 1504 1728  1024 1025 1028 1069 -hsync +vsync (80.2 kHz)
[    18.213] (II) RADEON(0): Modeline "1152x864_85.00"x85.0  119.65  1152 1224 1352 1552  864 865 868 907 -hsync +vsync (77.1 kHz)
[    18.213] (II) RADEON(0): Modeline "1024x768_85.00"x85.0   94.39  1024 1088 1200 1376  768 769 772 807 -hsync +vsync (68.6 kHz)
[    18.213] (II) RADEON(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz e)
[    18.213] (II) RADEON(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz e)
[    18.213] (II) RADEON(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz e)
[    18.213] (II) RADEON(0): Modeline "848x480"x60.0   33.75  848 864 976 1088  480 486 494 517 +hsync +vsync (31.0 kHz e)
[    18.213] (II) RADEON(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 489 492 525 -hsync -vsync (31.5 kHz e)
[    18.235] (II) RADEON(0): EDID for output DVI-0
[    18.255] (II) RADEON(0): EDID for output S-video
[    18.255] (II) RADEON(0): Output VGA-0 connected
[    18.255] (II) RADEON(0): Output DVI-0 disconnected
[    18.255] (II) RADEON(0): Output S-video disconnected
[    18.255] (II) RADEON(0): Using exact sizes for initial modes
[    18.255] (II) RADEON(0): Output VGA-0 using initial mode 1152x864_85.00
[    18.255] (II) RADEON(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[    18.255] (II) RADEON(0): mem size init: gart size :1fdff000 vram size: s:8000000 visible:7cc0000
[    18.255] (II) RADEON(0): EXA: Driver will not allow EXA pixmaps in VRAM
[    18.255] (**) RADEON(0): Display dimensions: (320, 240) mm
[    18.255] (**) RADEON(0): DPI set to (91, 91)
[    18.255] (II) Loading sub module "fb"
[    18.256] (II) LoadModule: "fb"
[    18.256] (II) Loading /usr/lib/xorg/modules/libfb.so
[    18.310] (II) Module fb: vendor="X.Org Foundation"
[    18.310]    compiled for 1.14.5, module version = 1.0.0
[    18.310]    ABI class: X.Org ANSI C Emulation, version 0.4
[    18.310] (II) Loading sub module "ramdac"
[    18.310] (II) LoadModule: "ramdac"
[    18.310] (II) Module "ramdac" already built-in
[    18.310] (--) Depth 24 pixmap format is 32 bpp
[    18.311] (II) RADEON(0): [DRI2] Setup complete
[    18.311] (II) RADEON(0): [DRI2]   DRI driver: r300
[    18.311] (II) RADEON(0): [DRI2]   VDPAU driver: r300
[    18.311] (II) RADEON(0): Front buffer size: 3888K
[    18.311] (II) RADEON(0): VRAM usage limit set to 111441K
[    18.312] (==) RADEON(0): Backing store disabled
[    18.313] (II) RADEON(0): Direct rendering enabled
[    18.313] (II) EXA(0): Driver allocated offscreen pixmaps
[    18.313] (II) EXA(0): Driver registered support for the following operations:
[    18.313] (II)         Solid
[    18.313] (II)         Copy
[    18.313] (II)         UploadToScreen
[    18.313] (II)         DownloadFromScreen
[    18.313] (II) RADEON(0): Acceleration enabled
[    18.313] (==) RADEON(0): DPMS enabled
[    18.313] (==) RADEON(0): Silken mouse enabled
[    18.313] (II) RADEON(0): Set up textured video
[    18.313] (II) RADEON(0): [XvMC] Associated with Radeon Textured Video.
[    18.313] (II) RADEON(0): [XvMC] Extension initialized.
[    18.313] (II) RADEON(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[    18.314] (--) RandR disabled
[    18.342] (II) SELinux: Disabled on system
[    19.384] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[    19.384] (II) AIGLX: enabled GLX_INTEL_swap_event
[    19.385] (II) AIGLX: enabled GLX_ARB_create_context
[    19.385] (II) AIGLX: enabled GLX_ARB_create_context_profile
[    19.385] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[    19.385] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[    19.385] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[    19.385] (II) AIGLX: Loaded and initialized r300
[    19.385] (II) GLX: Initialized DRI2 GL provider for screen 0
[    19.440] (II) RADEON(0): Setting screen physical size to 320 x 240
[    19.716] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    19.716] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    19.716] (II) LoadModule: "evdev"
[    19.716] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    19.744] (II) Module evdev: vendor="X.Org Foundation"
[    19.744]    compiled for 1.14.3, module version = 2.8.2
[    19.744]    Module class: X.Org XInput Driver
[    19.744]    ABI class: X.Org XInput driver, version 19.1
[    19.744] (II) Using input driver 'evdev' for 'Power Button'
[    19.744] (**) Power Button: always reports core events
[    19.744] (**) evdev: Power Button: Device: "/dev/input/event2"
[    19.744] (--) evdev: Power Button: Vendor 0 Product 0x1
[    19.744] (--) evdev: Power Button: Found keys
[    19.744] (II) evdev: Power Button: Configuring as keyboard
[    19.745] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2"
[    19.745] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    19.745] (**) Option "xkb_rules" "evdev"
[    19.745] (**) Option "xkb_model" "pc105"
[    19.745] (**) Option "xkb_layout" "us"
[    19.746] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    19.746] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[    19.746] (II) Using input driver 'evdev' for 'Power Button'
[    19.746] (**) Power Button: always reports core events
[    19.746] (**) evdev: Power Button: Device: "/dev/input/event1"
[    19.746] (--) evdev: Power Button: Vendor 0 Product 0x1
[    19.746] (--) evdev: Power Button: Found keys
[    19.746] (II) evdev: Power Button: Configuring as keyboard
[    19.746] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event1"
[    19.746] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[    19.746] (**) Option "xkb_rules" "evdev"
[    19.746] (**) Option "xkb_model" "pc105"
[    19.746] (**) Option "xkb_layout" "us"
[    19.747] (II) config/udev: Adding drm device (/dev/dri/card0)
[    19.747] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    19.747] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[    19.747] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[    19.747] (**) AT Translated Set 2 keyboard: always reports core events
[    19.747] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[    19.747] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[    19.747] (--) evdev: AT Translated Set 2 keyboard: Found keys
[    19.748] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[    19.748] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    19.748] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 8)
[    19.748] (**) Option "xkb_rules" "evdev"
[    19.748] (**) Option "xkb_model" "pc105"
[    19.748] (**) Option "xkb_layout" "us"
[    19.748] (II) config/udev: Adding input device ImPS/2 Generic Wheel Mouse (/dev/input/event4)
[    19.749] (**) ImPS/2 Generic Wheel Mouse: Applying InputClass "evdev pointer catchall"
[    19.749] (II) Using input driver 'evdev' for 'ImPS/2 Generic Wheel Mouse'
[    19.749] (**) ImPS/2 Generic Wheel Mouse: always reports core events
[    19.749] (**) evdev: ImPS/2 Generic Wheel Mouse: Device: "/dev/input/event4"
[    19.749] (--) evdev: ImPS/2 Generic Wheel Mouse: Vendor 0x2 Product 0x5
[    19.749] (--) evdev: ImPS/2 Generic Wheel Mouse: Found 3 mouse buttons
[    19.749] (--) evdev: ImPS/2 Generic Wheel Mouse: Found scroll wheel(s)
[    19.749] (--) evdev: ImPS/2 Generic Wheel Mouse: Found relative axes
[    19.749] (--) evdev: ImPS/2 Generic Wheel Mouse: Found x and y relative axes
[    19.749] (II) evdev: ImPS/2 Generic Wheel Mouse: Configuring as mouse
[    19.749] (II) evdev: ImPS/2 Generic Wheel Mouse: Adding scrollwheel support
[    19.749] (**) evdev: ImPS/2 Generic Wheel Mouse: YAxisMapping: buttons 4 and 5
[    19.749] (**) evdev: ImPS/2 Generic Wheel Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    19.749] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input5/event4"
[    19.749] (II) XINPUT: Adding extended input device "ImPS/2 Generic Wheel Mouse" (type: MOUSE, id 9)
[    19.749] (II) evdev: ImPS/2 Generic Wheel Mouse: initialized for relative axes.
[    19.749] (**) ImPS/2 Generic Wheel Mouse: (accel) keeping acceleration scheme 1
[    19.749] (**) ImPS/2 Generic Wheel Mouse: (accel) acceleration profile 0
[    19.750] (**) ImPS/2 Generic Wheel Mouse: (accel) acceleration factor: 2.000
[    19.750] (**) ImPS/2 Generic Wheel Mouse: (accel) acceleration threshold: 4
[    19.750] (II) config/udev: Adding input device ImPS/2 Generic Wheel Mouse (/dev/input/mouse0)
[    19.750] (II) No input driver specified, ignoring this device.
[    19.750] (II) This device may have been added with another device file.
[    19.750] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[    19.750] (II) No input driver specified, ignoring this device.
[    19.750] (II) This device may have been added with another device file.
[    23.766] (II) RADEON(0): Allocate new frame buffer 1280x1024 stride 1280
[    23.766] (II) RADEON(0): VRAM usage limit set to 110332K
[   218.562] (II) RADEON(0): Allocate new frame buffer 1152x864 stride 1152
[   218.563] (II) RADEON(0): VRAM usage limit set to 111441K

udev information:
-----------------
P: /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
E: DEVPATH=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
E: EV=3
E: ID_FOR_SEAT=input-acpi-LNXPWRBN_00
E: ID_INPUT=1
E: ID_INPUT_KEY=1
E: ID_PATH=acpi-LNXPWRBN:00
E: ID_PATH_TAG=acpi-LNXPWRBN_00
E: KEY=100000 0 0 0
E: MODALIAS=input:b0019v0000p0001e0000-e0,1,k74,ramlsfw
E: NAME="Power Button"
E: PHYS="LNXPWRBN/button/input0"
E: PRODUCT=19/0/1/0
E: PROP=0
E: SUBSYSTEM=input
E: TAGS=:seat:
E: USEC_INITIALIZED=33761

P: /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2
N: input/event2
E: BACKSPACE=guess
E: DEVNAME=/dev/input/event2
E: DEVPATH=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2
E: DMI_VENDOR=Dell Inc.
E: ID_INPUT=1
E: ID_INPUT_KEY=1
E: ID_PATH=acpi-LNXPWRBN:00
E: ID_PATH_TAG=acpi-LNXPWRBN_00
E: MAJOR=13
E: MINOR=66
E: SUBSYSTEM=input
E: TAGS=:power-switch:
E: USEC_INITIALIZED=72140
E: XKBLAYOUT=us
E: XKBMODEL=pc105

P: /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
E: DEVPATH=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
E: EV=3
E: ID_FOR_SEAT=input-acpi-PNP0C0C_00
E: ID_INPUT=1
E: ID_INPUT_KEY=1
E: ID_PATH=acpi-PNP0C0C:00
E: ID_PATH_TAG=acpi-PNP0C0C_00
E: KEY=100000 0 0 0
E: MODALIAS=input:b0019v0000p0001e0000-e0,1,k74,ramlsfw
E: NAME="Power Button"
E: PHYS="PNP0C0C/button/input0"
E: PRODUCT=19/0/1/0
E: PROP=0
E: SUBSYSTEM=input
E: TAGS=:seat:
E: USEC_INITIALIZED=33152

P: /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event1
N: input/event1
E: BACKSPACE=guess
E: DEVNAME=/dev/input/event1
E: DEVPATH=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event1
E: DMI_VENDOR=Dell Inc.
E: ID_INPUT=1
E: ID_INPUT_KEY=1
E: ID_PATH=acpi-PNP0C0C:00
E: ID_PATH_TAG=acpi-PNP0C0C_00
E: MAJOR=13
E: MINOR=65
E: SUBSYSTEM=input
E: TAGS=:power-switch:
E: USEC_INITIALIZED=71374
E: XKBLAYOUT=us
E: XKBMODEL=pc105

P: /devices/platform/i8042/serio0/input/input0
E: DEVPATH=/devices/platform/i8042/serio0/input/input0
E: EV=120013
E: ID_FOR_SEAT=input-platform-i8042-serio-0
E: ID_INPUT=1
E: ID_INPUT_KEY=1
E: ID_INPUT_KEYBOARD=1
E: ID_PATH=platform-i8042-serio-0
E: ID_PATH_TAG=platform-i8042-serio-0
E: ID_SERIAL=noserial
E: KEY=1100f 2902002 8380307c f910f001 feffffdf ffefffff ffffffff fffffffe
E: LED=7
E: MODALIAS=input:b0011v0001p0001eAB41-e0,1,4,11,14,k71,72,73,74,75,76,77,79,7A,7B,7C,7D,7E,7F,80,8C,8D,8E,8F,94,98,9B,9C,9D,9E,9F,A2,A3,A4,A5,A6,AC,AD,B7,B8,B9,BF,C1,CD,D4,D7,D9,E0,E1,E2,E3,EC,F0,ram4,l0,1,2,sfw
E: MSC=10
E: NAME="AT Translated Set 2 keyboard"
E: PHYS="isa0060/serio0/input0"
E: PRODUCT=11/1/1/ab41
E: PROP=0
E: SUBSYSTEM=input
E: TAGS=:seat:
E: USEC_INITIALIZED=1188

P: /devices/platform/i8042/serio0/input/input0/event0
N: input/event0
S: input/by-path/platform-i8042-serio-0-event-kbd
E: BACKSPACE=guess
E: DEVLINKS=/dev/input/by-path/platform-i8042-serio-0-event-kbd
E: DEVNAME=/dev/input/event0
E: DEVPATH=/devices/platform/i8042/serio0/input/input0/event0
E: DMI_VENDOR=Dell Inc.
E: ID_INPUT=1
E: ID_INPUT_KEY=1
E: ID_INPUT_KEYBOARD=1
E: ID_PATH=platform-i8042-serio-0
E: ID_PATH_TAG=platform-i8042-serio-0
E: ID_SERIAL=noserial
E: MAJOR=13
E: MINOR=64
E: SUBSYSTEM=input
E: USEC_INITIALIZED=70208
E: XKBLAYOUT=us
E: XKBMODEL=pc105

P: /devices/platform/i8042/serio1/input/input5
E: DEVPATH=/devices/platform/i8042/serio1/input/input5
E: EV=7
E: ID_FOR_SEAT=input-platform-i8042-serio-1
E: ID_INPUT=1
E: ID_INPUT_MOUSE=1
E: ID_PATH=platform-i8042-serio-1
E: ID_PATH_TAG=platform-i8042-serio-1
E: ID_SERIAL=noserial
E: KEY=70000 0 0 0 0 0 0 0 0
E: MODALIAS=input:b0011v0002p0005e0000-e0,1,2,k110,111,112,r0,1,8,amlsfw
E: NAME="ImPS/2 Generic Wheel Mouse"
E: PHYS="isa0060/serio1/input0"
E: PRODUCT=11/2/5/0
E: PROP=0
E: REL=103
E: SUBSYSTEM=input
E: TAGS=:seat:
E: USEC_INITIALIZED=12077

P: /devices/platform/i8042/serio1/input/input5/event4
N: input/event4
S: input/by-path/platform-i8042-serio-1-event-mouse
E: DEVLINKS=/dev/input/by-path/platform-i8042-serio-1-event-mouse
E: DEVNAME=/dev/input/event4
E: DEVPATH=/devices/platform/i8042/serio1/input/input5/event4
E: ID_INPUT=1
E: ID_INPUT_MOUSE=1
E: ID_PATH=platform-i8042-serio-1
E: ID_PATH_TAG=platform-i8042-serio-1
E: ID_SERIAL=noserial
E: MAJOR=13
E: MINOR=68
E: SUBSYSTEM=input
E: USEC_INITIALIZED=12321

P: /devices/platform/i8042/serio1/input/input5/mouse0
N: input/mouse0
S: input/by-path/platform-i8042-serio-1-mouse
E: DEVLINKS=/dev/input/by-path/platform-i8042-serio-1-mouse
E: DEVNAME=/dev/input/mouse0
E: DEVPATH=/devices/platform/i8042/serio1/input/input5/mouse0
E: ID_INPUT=1
E: ID_INPUT_MOUSE=1
E: ID_PATH=platform-i8042-serio-1
E: ID_PATH_TAG=platform-i8042-serio-1
E: ID_SERIAL=noserial
E: MAJOR=13
E: MINOR=32
E: SUBSYSTEM=input
E: USEC_INITIALIZED=12288

P: /devices/platform/pcspkr/input/input4
E: DEVPATH=/devices/platform/pcspkr/input/input4
E: EV=40001
E: ID_FOR_SEAT=input-platform-pcspkr
E: ID_INPUT=1
E: ID_PATH=platform-pcspkr
E: ID_PATH_TAG=platform-pcspkr
E: ID_SERIAL=noserial
E: MODALIAS=input:b0010v001Fp0001e0100-e0,12,kramls1,2,fw
E: NAME="PC Speaker"
E: PHYS="isa0061/input0"
E: PRODUCT=10/1f/1/100
E: PROP=0
E: SND=6
E: SUBSYSTEM=input
E: TAGS=:seat:
E: USEC_INITIALIZED=27620

P: /devices/platform/pcspkr/input/input4/event3
N: input/event3
S: input/by-path/platform-pcspkr-event-spkr
E: DEVLINKS=/dev/input/by-path/platform-pcspkr-event-spkr
E: DEVNAME=/dev/input/event3
E: DEVPATH=/devices/platform/pcspkr/input/input4/event3
E: ID_INPUT=1
E: ID_PATH=platform-pcspkr
E: ID_PATH_TAG=platform-pcspkr
E: ID_SERIAL=noserial
E: MAJOR=13
E: MINOR=67
E: SUBSYSTEM=input
E: USEC_INITIALIZED=28449


DRM Information from dmesg:
---------------------------
[    1.087468] Linux agpgart interface v0.103
[    4.476886] [drm] Initialized drm 1.1.0 20060810
[    4.924065] [drm] radeon kernel modesetting enabled.
[    4.924645] [drm] initializing kernel modesetting (RV380 0x1002:0x5B60 0x1002:0x0302).
[    4.924676] [drm] register mmio base: 0xDFDE0000
[    4.924681] [drm] register mmio size: 65536
[    4.924772] [drm] Generation 2 PCI interface, using max accessible memory
[    4.924794] [drm] Detected VRAM RAM=128M, BAR=128M
[    4.924797] [drm] RAM width 64bits DDR
[    4.924926] [drm] radeon: 128M of VRAM memory ready
[    4.924930] [drm] radeon: 512M of GTT memory ready.
[    4.924952] [drm] GART: num cpu pages 131072, num gpu pages 131072
[    4.926032] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[    4.927353] [drm] PCIE GART of 512M enabled (table at 0x00000000D0040000).
[    4.927401] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    4.927403] [drm] Driver supports precise vblank timestamp query.
[    4.927487] [drm] radeon: irq initialized.
[    4.927507] [drm] Loading R300 Microcode
[    5.088795] [drm] radeon: ring at 0x00000000B0001000
[    5.088820] [drm] ring test succeeded in 1 usecs
[    5.088980] [drm] ib test succeeded in 0 usecs
[    5.089412] [drm] Radeon Display Connectors
[    5.089417] [drm] Connector 0:
[    5.089421] [drm]   VGA-1
[    5.089426] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[    5.089430] [drm]   Encoders:
[    5.089433] [drm]     CRT1: INTERNAL_DAC1
[    5.089436] [drm] Connector 1:
[    5.089440] [drm]   DVI-I-1
[    5.089443] [drm]   HPD1
[    5.089447] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[    5.089450] [drm]   Encoders:
[    5.089454] [drm]     CRT2: INTERNAL_DAC2
[    5.089457] [drm]     DFP1: INTERNAL_TMDS1
[    5.089460] [drm] Connector 2:
[    5.089463] [drm]   SVIDEO-1
[    5.089466] [drm]   Encoders:
[    5.089469] [drm]     TV1: INTERNAL_DAC2
[    5.117969] [drm] fb mappable at 0xD00C0000
[    5.117973] [drm] vram apper at 0xD0000000
[    5.117992] [drm] size 3145728
[    5.117996] [drm] fb depth is 24
[    5.117999] [drm]    pitch is 4096
[    5.118149] fbcon: radeondrmfb (fb0) is primary device
[    5.180460] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[    5.180486] [drm] Initialized radeon 2.34.0 20080528 for 0000:01:00.0 on minor 0
Debian&Me
 
Posts: 3
Joined: 2014-02-15 00:44

Re: Lockups occur after installation of firmware-linux-nonfr

Postby Hralgmir » 2014-02-28 13:52

I have a couple of old Dell CPx 's, 450 & 500. The 500 started doing this, after 30 minutes or an hour it would freeze. But I came to the conclusion it was probably a motherboard fault, as I was using the same HDD, and have put the 500 CPU in the 450 after upgrading the BIOS. I was thinking of putting together the old chassis and trying it with a BIOS upgrade sometime - perhaps if the BIOS had got corrupted it could cause a problem, something like that might be worth a try. However, before looking at hardware, I suggest putting the software back as it was before the problem occurred, and uninstalling the suspect packages.
syslog (also check syslog.1) would be recording up to the point of the lock up and saving the results, check the times and reference to the time the lock up occurs. Perhaps something would show in there. Another consideration might be whether you could swap the graphics card, if altering graphics settings makes a difference. Check the well known auction website for cheap second hand parts to try:). If you play around with this stuff I advise you to heed BIOS warning messages and do not try to override them if they occur.
It's possible it could be a software problem though.
Hralgmir
 
Posts: 48
Joined: 2012-07-16 01:05

Re: Lockups occur after installation of firmware-linux-nonfr

Postby Hralgmir » 2014-03-11 02:46

I remembered subsequently I also once programmatically created this symptom (accidentally) by writing a faulty kernel driver module using kmalloc.
See here at the end of xorg
[ 24.165] (II) RADEON(0): VRAM usage limit set to 110332K
[ 47.739] (II) RADEON(0): Allocate new frame buffer 1152x864 stride 1152
[ 47.739] (II) RADEON(0): VRAM usage limit set to 111441K

VRAM, allocating new frame buffer? Sounds a bit like dynamic memory allocation to me. Could be worth grepping the source to see where the syslog messages are output from.
The kernel is sensitive about memory allocation errors, unlike userspace code which just fails with an error message. Of course if it is non free then it is beyond fixing if the source is not available. The kernel changes internally and breaks drivers sometimes, unless the driver writers keep their code up to date promptly.
I tried installing a non free graphics driver once but I never got it to work, actually it caused the boot sequence to fail before it got to the desktop and I had to undo it via rescue mode. It seemed to be mostly designed for Redhat distros but it could just have been my fault.
It might actually be easier to implement the graphics features you require by rewriting the open source driver instead. :)
Hralgmir
 
Posts: 48
Joined: 2012-07-16 01:05

Re: Lockups occur after installation of firmware-linux-nonfr

Postby burpoups » 2014-10-22 22:35

Any news on this ?
I encounter the same problem : almost always when I logout from KDE session the system hangs as you describe (and sometimes during normal use, although seldomly).
It seems to be related to firmware-linux-nonfree package -- required only to enable KMS and enable proper resolution setting (otherwise I am locked to 1280x1024 pixels max).
I have double checked that removing this package stops hangs. I am not interested in 3D perfo.

As package has been installated quite a long time ago by now (almost one year), and it was working fine until last month, this seems to be related to kernel evolution.
# uname -a
Linux jupi 3.16-2-amd64 #1 SMP Debian 3.16.3-2 (2014-09-20) x86_64 GNU/Linux
# lspci | grep -i VGA
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Pitcairn XT [Radeon HD 7870 GHz Edition]
# dmesg | grep firmware
[ 3.473774] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/PITCAIRN_pfp.bin
[ 3.474601] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/PITCAIRN_me.bin
[ 3.475590] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/PITCAIRN_ce.bin
[ 3.477417] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/PITCAIRN_rlc.bin
[ 3.478164] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/PITCAIRN_mc2.bin
[ 3.479100] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/PITCAIRN_smc.bin
[ 3.491052] radeon 0000:01:00.0: firmware: direct-loading firmware radeon/TAHITI_uvd.bin

Debian GNU/Linux jessie/sid
xserver-xorg-video-ati 1:7.5.0-1
firmware-linux-nonfree 0.43
burpoups
 
Posts: 1
Joined: 2014-10-22 22:03

Re: Lockups occur after installation of firmware-linux-nonfr

Postby Hypex » 2017-02-12 11:24

I am thinking that this is a common issue with the firmware-linux-nonfree drivers.

I recently hacked together a Jessie installer for a (now old) PowerPC machine. Based on kernel 3.16-4. With an ATI 9200SE. I soon found out that GDM wouldn't load up and was getting a black screen. The log showing is it failed on lack of 3d acceleration.

So I spent too long trying to get a desktop up. I managed to install lightdm and LXDE. And got as far as a login screen. But then it failed again. Due to it still trying to use Gnome. ;-)

There were the usual messages of no "/dev/dri/card0" and falling back to software raster. Then it all changed. Through looking here on the net I was inspired to install firmware-linux-nonfree. For some reason it wasn't found at first and I had to play with the sources list so I could apt-get it. I then found I needed to use "video=radeonfb:off" in my boot args to enable KMS, DRM and DRI to work. And in the messages GLX and other features enabled.

But it wasn't to last and this is the point of my post. 3d still failed so Gnome still wouldn't load from the login screen but LXDE did work and also Mate after I installed it. I can use the desktop for a few minutes and then it freezes. In my case under five. Total lock up. One time the cursor still moved around so it looked like the system still worked. Only just.

Perhaps at this point a null modem cable to a terminal and debug mode enabled in the kernel if possible might catch it. :-)
Hypex
 
Posts: 25
Joined: 2016-09-23 04:39
Location: Southern Aussieland


Return to Hardware

Who is online

Users browsing this forum: No registered users and 9 guests

fashionable