USB HDD Problems

Getting your soundcard to work, using Debian on non-i386 hardware, etc

Postby robselina » 2007-04-12 16:13

your kernel seems to identify two separate UHCI USB controllers, instead of a UHCI and an EHCI controller. That's probably not the problem, but it's reason enough to upgrade the kernel so I'd do that for starters and maybe you'll get lucky with the newer kernel.

What does lspci say about USB hubs/controllers?
-- Rob
robselina
 
Posts: 56
Joined: 2006-10-10 01:46

Postby madjalapeno » 2007-04-12 16:22

Ahhhh, I think you've found something with that last one

Code: Select all
debian:/# lspci
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia] (rev 05)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia AGP]
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10)
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
0000:00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e)
0000:00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e)
0000:00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10)
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40)
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51)
0000:01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 6a)
debian:/#


It looks like it's only finding USB 1.1 Controllers. :shock: Speaking as a newb I would have thought it would find the drive, but it would be slooow.

What should I do to fix it?

Back to the slugs - I'm using mt-daapd to serve music files to my Roku, which is a great system.

thanks
madjalapeno
 
Posts: 12
Joined: 2007-04-09 19:46
Location: NH, USA

Postby robselina » 2007-04-12 16:32

I think that board may just be USB 1.1 :cry:

You're right, it'll be very slow for transfers since you'll get no more than 1.5MB/sec through the USB ports......

Got a link to your board specs?

If you have an open PCI port you can add a USB 2.0 controller, but i suspect that board doesn't have many......

If you're sure it's supposed to have USB 2.0, try the kernel update but I've never seen the lspci output change based on the kernel available.....
Last edited by robselina on 2007-04-12 16:39, edited 1 time in total.
-- Rob
robselina
 
Posts: 56
Joined: 2006-10-10 01:46

Postby robselina » 2007-04-12 16:38

madjalapeno wrote:Back to the slugs - I'm using mt-daapd to serve music files to my Roku, which is a great system.


Fun stuff! I'm starting pretty basic, I'll have most of my files on SMB shares and with the HTPC they'll all be mouted using SMBFS. Should give me access to everything but it's not quite as neat of a solution as the ROKU since I don't have a good remote or front-pannel setup yet to do some basic functions w/o the TV....
-- Rob
robselina
 
Posts: 56
Joined: 2006-10-10 01:46

Postby madjalapeno » 2007-04-12 16:54

I have a USB PCI card, but it will have to wait until I get home, as even though SSH is great, adding an external card is still beyond it (and me) :lol:

If you ever get a chance to get a Roku make sure you do - it takes your music collection to another level. It's silent and so convenient, and has high wife approval value. Heck, it's worth it for Radio Paradise alone.
madjalapeno
 
Posts: 12
Joined: 2007-04-09 19:46
Location: NH, USA

Postby madjalapeno » 2007-04-13 00:00

Home again. Just plugged my PCI usb card in, plugged the WD 500Gb disk in. Powered up and ....

Code: Select all
debian:~# dmesg
Linux version 2.6.8-3-386 (pbuilder@dl360-g3) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Wed Dec 6 00:38:53 UTC 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002f7f0000 (usable)
 BIOS-e820: 000000002f7f0000 - 000000002f7f3000 (ACPI NVS)
 BIOS-e820: 000000002f7f3000 - 000000002f800000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
759MB LOWMEM available.
On node 0 totalpages: 194544
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 190448 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VIA601                                    ) @ 0x000f67c0
ACPI: RSDT (v001 VIA601 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2f7f3000
ACPI: FADT (v001 VIA601 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2f7f3040
ACPI: DSDT (v001 VIA601 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro devfs=nomount
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 800.263 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 762956k/778176k available (1338k kernel code, 14444k reserved, 731k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1585.15 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps:        00803135 80803035 00000000 00000000
CPU: Centaur VIA Samuel 2 stepping 03
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4192k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3a0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ3 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbda0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbdd0, dseg 0xf0000
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI interrupt 0000:00:14.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:14.2[C] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:14.3[A] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4192 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 4R080L0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(33)
 /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2289220k swap on /dev/hda5.  Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Capability LSM initialized
irda_init()
NET: Registered protocol family 23
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:00:14.3[A] -> GSI 12 (level, low) -> IRQ 12
ieee1394: warning: Invalid max packet size of 2, setting to 512
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[12]  MMIO=[d7002000-d70027ff]  Max Packet=[512]
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0xd800, 00:40:63:ca:c7:f6, IRQ 11.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 45e1.
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
via82cxxx: board #1 at 0xCC00, IRQ 10
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[001106000000e332]
ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:11.2: irq 5, io base 0000c400
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:11.3: irq 5, io base 0000c800
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:14.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:14.0: irq 12, io base 0000dc00
uhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:14.1[B] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:14.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:14.1: irq 10, io base 0000e000
uhci_hcd 0000:00:14.1: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 3-1: new full speed USB device using address 2
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
  Vendor: WD        Model: 5000KS External   Rev: 106a
  Type:   Direct-Access                      ANSI SCSI revision: 02
ACPI: PCI interrupt 0000:00:14.2[C] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:14.2: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:14.2: irq 5, pci mem f02e0000
ehci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:14.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
usb 3-1: USB disconnect, address 2
sda : READ CAPACITY failed.
sda : status=0, message=00, host=7, driver=00
sda : sense not available.
sda: assuming drive cache: write through
 /dev/scsi/host0/bus0/target0/lun0:SCSI error : <0 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
SCSI error : <0 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
 unable to read partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbhid: probe of 3-1:1.1 failed with error -5
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 4 ports detected
usb 5-1: new high speed USB device using address 2
scsi1 : SCSI emulation for USB Mass Storage devices
  Vendor: WD        Model: 5000KS External   Rev: 106a
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: assuming drive cache: write through
 /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
USB Mass Storage device found at 2
drivers/usb/input/hid-core.c: ctrl urb status -32 received
input: USB HID v1.11 Device [Western Digital External HDD] on usb-0000:00:14.2-1
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset
agpgart: Maximum main memory to use for agp memory: 682M
agpgart: AGP aperture is 64M @ 0xd0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
Real Time Clock Driver v1.12
input: PC Speaker
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
NET: Registered protocol family 17
NET: Registered protocol family 5
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02cc960(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present


So this time have some new error messages about it failing to read the partition table.

Nothing is showing up under SDA or SCSI in the /dev directory.

My fstab looks like this:

Code: Select all
# /etc/fstab: static file system information.
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
proc            /proc           proc    defaults        0       0
/dev/hda1       /               ext3    defaults,errors=remount-ro 0       1
/dev/hda5       none            swap    sw              0       0
/dev/hdc        /media/cdrom0   iso9660 ro,user,noauto  0       0
/dev/fd0        /media/floppy0  auto    rw,user,noauto  0       0
/dev/usb_WD500  /media/WD5001   ext3    rw,user,noauto  0       0
none            /sys            sysfs   defaults        0       0


Thanks

Mike
madjalapeno
 
Posts: 12
Joined: 2007-04-09 19:46
Location: NH, USA

Postby madjalapeno » 2007-04-13 02:36

The PCI USB card also has firewire, and so does the WD500, so ...

shutdown the box, unplugged the USD connection and plugged in the Firewire, rebooted, logged in and typed 'dmesg':

Code: Select all

debian:~# dmesg
Linux version 2.6.8-3-386 (pbuilder@dl360-g3) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Wed Dec 6 00:38:53 UTC 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002f7f0000 (usable)
 BIOS-e820: 000000002f7f0000 - 000000002f7f3000 (ACPI NVS)
 BIOS-e820: 000000002f7f3000 - 000000002f800000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
759MB LOWMEM available.
On node 0 totalpages: 194544
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 190448 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VIA601                                    ) @ 0x000f67c0
ACPI: RSDT (v001 VIA601 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2f7f3000
ACPI: FADT (v001 VIA601 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2f7f3040
ACPI: DSDT (v001 VIA601 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro devfs=nomount
No local APIC present or hardware disabled
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 800.263 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 762956k/778176k available (1338k kernel code, 14444k reserved, 731k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1585.15 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps:        00803135 80803035 00000000 00000000
CPU: Centaur VIA Samuel 2 stepping 03
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4192k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3a0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ3 SCI: Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbda0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbdd0, dseg 0xf0000
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI interrupt 0000:00:14.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:14.2[C] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:00:14.3[A] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4192 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
hda: Maxtor 4R080L0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(33)
 /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2289220k swap on /dev/hda5.  Priority:-1 extents:1
EXT3 FS on hda1, internal journal
Capability LSM initialized
irda_init()
NET: Registered protocol family 23
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:00:14.3[A] -> GSI 12 (level, low) -> IRQ 12
ieee1394: warning: Invalid max packet size of 2, setting to 512
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[12]  MMIO=[d7002000-d70027ff]  Max Packet=[512]
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0xd800, 00:40:63:ca:c7:f6, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
via82cxxx: board #1 at 0xCC00, IRQ 10
ieee1394: Node added: ID:BUS[0-00:1023]  GUID[0090a990e011379d]
ieee1394: Host added: ID:BUS[0-01:1023]  GUID[001106000000e332]
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
scsi0 : SCSI emulation for IEEE-1394 SBP-2 Devices
ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:11.2: irq 5, io base 0000c400
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:11.3: irq 5, io base 0000c800
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:14.0[A] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:14.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
ieee1394: sbp2: Logged into SBP-2 device
uhci_hcd 0000:00:14.0: irq 12, io base 0000dc00
ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [2048]
uhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
  Vendor: WD        Model: 5000KS External   Rev: 106a
  Type:   Direct-Access                      ANSI SCSI revision: 06
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: asking for cache data failed
sda: assuming drive cache: write through
 /dev/scsi/host0/bus0/target1/lun0: p1 p2 p3
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:14.1[B] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:14.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:14.1: irq 10, io base 0000e000
uhci_hcd 0000:00:14.1: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:14.2[C] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:14.2: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:14.2: irq 5, pci mem f0353000
ehci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:14.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 4 ports detected
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset
agpgart: Maximum main memory to use for agp memory: 682M
agpgart: AGP aperture is 64M @ 0xd0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
Real Time Clock Driver v1.12
input: PC Speaker
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
NET: Registered protocol family 17
NET: Registered protocol family 5
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02cc960(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
debian:~#




Still not mounting and still nothing in /dev :cry:
madjalapeno
 
Posts: 12
Joined: 2007-04-09 19:46
Location: NH, USA

Postby robselina » 2007-04-13 14:30

have you updated to the 2.6.18 kernel yet?
-- Rob
robselina
 
Posts: 56
Joined: 2006-10-10 01:46

Postby madjalapeno » 2007-04-13 14:41

Code: Select all
debian:/# uname -a
Linux debian 2.6.8-3-386 #1 Wed Dec 6 00:38:53 UTC 2006 i686 GNU/Linux
debian:/# debian:/#


Looks like I'm running 2.6.8-3 right now, so I'll try the kernel upgrade (even if I'm not getting the USB to work I sure am learning a lot.
madjalapeno
 
Posts: 12
Joined: 2007-04-09 19:46
Location: NH, USA

Postby robselina » 2007-04-13 15:04

madjalapeno wrote:
Code: Select all
debian:/# uname -a
Linux debian 2.6.8-3-386 #1 Wed Dec 6 00:38:53 UTC 2006 i686 GNU/Linux
debian:/# debian:/#


Looks like I'm running 2.6.8-3 right now, so I'll try the kernel upgrade (even if I'm not getting the USB to work I sure am learning a lot.


Depending on when you installed your system, you may be running Debian Sarge. Make sure you're up to date on Etch too. (it'll say version 4.0 when you get a login screen at boot)
-- Rob
robselina
 
Posts: 56
Joined: 2006-10-10 01:46

Postby madjalapeno » 2007-04-13 18:33

Code: Select all
debian:~# dmesg
Linux version 2.6.18-4-486 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Mon Mar 26 16:39:10 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002f7f0000 (usable)
 BIOS-e820: 000000002f7f0000 - 000000002f7f3000 (ACPI NVS)
 BIOS-e820: 000000002f7f3000 - 000000002f800000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
759MB LOWMEM available.
On node 0 totalpages: 194544
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 190448 pages, LIFO batch:31
DMI 2.2 present.
ACPI: RSDP (v000 VIA601                                ) @ 0x000f67c0
ACPI: RSDT (v001 VIA601 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2f7f3000
ACPI: FADT (v001 VIA601 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x2f7f3040
ACPI: DSDT (v001 VIA601 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 30000000 (gap: 2f800000:d07f0000)
Detected 800.065 MHz processor.
Built 1 zonelists.  Total pages: 194544
Kernel command line: root=/dev/hda1 ro
No local APIC present or hardware disabled
mapped APIC to ffffd000 (015f3000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 763104k/778176k available (1502k kernel code, 14484k reserved, 601k data, 256k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1601.65 BogoMIPS (lpj=3203310)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: Centaur VIA Samuel 2 stepping 03
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0008 (from 1c28)
checking if image is initramfs... it is
Freeing initrd memory: 4231k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3a0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: d4000000-d6ffffff
  PREFETCH window: 30000000-300fffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1176487719.492:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 256k freed
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (32 C)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ieee1394: Initialized config rom entry `ip1394'
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
hda: Maxtor 4R080L0, ATA DISK drive
Time: acpi_pm clocksource has been installed.
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.2: UHCI Host Controller
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:11.2: irq 5, io base 0x0000c400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: max request size: 512KiB
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
 hda: hda1 hda2 <<6>ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.3: UHCI Host Controller
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:11.3: irq 5, io base 0x0000c800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
 hda5 >
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:14.0: UHCI Host Controller
uhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:14.0: irq 12, io base 0x0000dc00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:14.1[B] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:14.1: UHCI Host Controller
uhci_hcd 0000:00:14.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:14.1: irq 10, io base 0x0000e000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:14.2[C] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:14.2: EHCI Host Controller
ehci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:14.2: irq 5, io mem 0xd7001000
ehci_hcd 0000:00:14.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:14.3[A] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[12]  MMIO=[d7002000-d70027ff]  Max Packet=[2]  IR/IT contexts=[4/8]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to setting max_packet_size to 512 bytes
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0x1d800, 00:40:63:ca:c7:f6, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Node added: ID:BUS[0-00:1023]  GUID[0090a990e011379d]
ieee1394: Host added: ID:BUS[0-01:1023]  GUID[001106000000e332]
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
SCSI subsystem initialized
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
scsi0 : SBP-2 IEEE-1394
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
irda_init()
NET: Registered protocol family 23
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset
agpgart: AGP aperture is 64M @ 0xd0000000
ieee1394: sbp2: Logged into SBP-2 device
ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [512]
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
input: PC Speaker as /class/input/input0
Real Time Clock Driver v1.12ac
ieee1394: sbp2: aborting sbp2 command
scsi 0:0:1:0:
        command: Inquiry: 12 00 00 00 24 00
  Vendor: WD        Model: 5000KS External   Rev: 106a
  Type:   Direct-Access                      ANSI SCSI revision: 04
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: cache data unavailable
sda: assuming drive cache: write through
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
sda: Mode Sense: 11 00 00 00
sda: cache data unavailable
sda: assuming drive cache: write through
 sda: sda1 sda2 sda3
sd 0:0:1:0: Attached scsi disk sda
Adding 2289220k swap on /dev/hda5.  Priority:-1 extents:1 across:2289220k
EXT3 FS on hda1, internal journal
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
NET: Registered protocol family 5
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
debian:~#


Mr Rob, looks like I may owe you a beer, I see mention of sda1,2 and 3 in there.

Code: Select all
debian:~# cd /dev
debian:/dev# ls
agpgart  psaux  ram3        tty13  tty39  tty7            usbdev3.1_ep00
audio    ptmx   ram4        tty14  tty4   tty8            usbdev3.1_ep81
bus      pts    ram5        tty15  tty40  tty9            usbdev4.1_ep00
console  ptyp0  ram6        tty16  tty41  ttyp0           usbdev4.1_ep81
core     ptyp1  ram7        tty17  tty42  ttyp1           usbdev5.1_ep00
disk     ptyp2  ram8        tty18  tty43  ttyp2           usbdev5.1_ep81
dspW     ptyp3  ram9        tty19  tty44  ttyp3           vcs
fd       ptyp4  random      tty2   tty45  ttyp4           vcs1
full     ptyp5  rtc         tty20  tty46  ttyp5           vcs2
hda      ptyp6  sda         tty21  tty47  ttyp6           vcs3
hda1     ptyp7  sda1        tty22  tty48  ttyp7           vcs4
hda2     ptyp8  sda2        tty23  tty49  ttyp8           vcs5
hda5     ptyp9  sda3        tty24  tty5   ttyp9           vcs6
hpet     ptypa  sequencer   tty25  tty50  ttypa           vcsa
initctl  ptypb  sequencer2  tty26  tty51  ttypb           vcsa1
input    ptypc  shm         tty27  tty52  ttypc           vcsa2
kmem     ptypd  snapshot    tty28  tty53  ttypd           vcsa3
kmsg     ptype  snd         tty29  tty54  ttype           vcsa4
log      ptypf  sndstat     tty3   tty55  ttypf           vcsa5
loop     ram0   stderr      tty30  tty56  ttyS0           vcsa6
MAKEDEV  ram1   stdin       tty31  tty57  ttyS1           xconsole
mapper   ram10  stdout      tty32  tty58  ttyS2           zero
mem      ram11  tty         tty33  tty59  ttyS3
net      ram12  tty0        tty34  tty6   urandom
null     ram13  tty1        tty35  tty60  usbdev1.1_ep00
port     ram14  tty10       tty36  tty61  usbdev1.1_ep81
ppp      ram15  tty11       tty37  tty62  usbdev2.1_ep00
printer  ram2   tty12       tty38  tty63  usbdev2.1_ep81
debian:/dev#


What would you recomend as the best way to mount sda1 and keep it mounted in the same place? Isn't this what udev is for?
madjalapeno
 
Posts: 12
Joined: 2007-04-09 19:46
Location: NH, USA

Postby ghostdawg » 2007-04-13 19:10

Below is a snippit of my dmesg showing my external HDD. If this is of any help.

I also have udev, pmount & hal installed and when I can access my ext. hdd and if I load a cd/dvd they are available without me doing anything.


usb-storage: device scan complete
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: sda1 sda2
sd 2:0:0:0: Attached scsi disk sda
Tower | Debian Testing & Mageia 1 | HP DX5150 AMD64 | 512gb | 40gb
AAO | Mandriva 2010.2 | Intel Atom | 1gb | 160gb
Mini Mac G4 | Debian & OSX | 1gb | 60gb
User avatar
ghostdawg
 
Posts: 1094
Joined: 2006-08-29 03:39
Location: STLMO

Postby robselina » 2007-04-13 19:35

score!

At present with only one dynamically assigned USB device (your single external HD), things should work fine since it'll always be sda, but once you add a few more, you need to make some udev rules. New territory for me, but here are some links:

http://priyadi.net/archives/2004/11/06/ ... ce-naming/

http://www.reactivated.net/writing_udev_rules.html

happy hunting!
-- Rob
robselina
 
Posts: 56
Joined: 2006-10-10 01:46

Postby madjalapeno » 2007-04-13 19:41

Rob (and everyone),

thanks for all your help. I know some people would consider it a basic problem, but when you are new to all this it's damned complicated.

Next it's getting a CP2101 USB device to work, but that's another topic ...
Every job needs a new tool, I personally buy the tool and then find a job for it.
madjalapeno
 
Posts: 12
Joined: 2007-04-09 19:46
Location: NH, USA

Previous

Return to Hardware

Who is online

Users browsing this forum: No registered users and 7 guests

fashionable