Same issue here with Stretch + Realtek 8187, here goes my outputs.
Code: Select all
uname -a
Linux debian 4.9.0-3-amd64 #1 SMP Debian 4.9.25-1 (2017-05-02) x86_64 GNU/Linux
Output for dmesg:
Code: Select all
[ 1.515779] usb 2-2: New USB device found, idVendor=0bda, idProduct=8187
[ 1.515781] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.515782] usb 2-2: Product: RTL8187_Wireless
[ 1.515783] usb 2-2: Manufacturer: Manufacturer_Realtek_RTL8187_
[ 1.515784] usb 2-2: SerialNumber: 000F1065113B
[ 11.487047] rtl8187: Customer ID is 0x00
[ 11.487369] rtl8187: wireless switch is on
[ 11.487391] usbcore: registered new interface driver rtl8187
[ 12.860421] rtl8187 2-2:1.0 wlx000f1065113b: renamed from wlan0
[ 31.955360] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 89.984385] wlx000f1065113b: authenticate with c8:b3:73:3e:25:d3
[ 90.257065] wlx000f1065113b: send auth to c8:b3:73:3e:25:d3 (try 1/3)
[ 90.258770] wlx000f1065113b: authenticated
[ 95.261539] wlx000f1065113b: aborting authentication with c8:b3:73:3e:25:d3 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 97.540347] wlx000f1065113b: authenticate with c8:b3:73:3e:25:d3
[ 97.805293] wlx000f1065113b: send auth to c8:b3:73:3e:25:d3 (try 1/3)
[ 97.807409] wlx000f1065113b: authenticated
[ 102.808071] wlx000f1065113b: aborting authentication with c8:b3:73:3e:25:d3 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 105.484754] wlx000f1065113b: authenticate with c8:b3:73:3e:25:d3
[ 105.745444] wlx000f1065113b: send auth to c8:b3:73:3e:25:d3 (try 1/3)
[ 105.751611] wlx000f1065113b: authenticated
[ 110.748324] wlx000f1065113b: aborting authentication with c8:b3:73:3e:25:d3 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 113.010862] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 115.117259] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 659.023492] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 669.671665] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 671.583986] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 676.860092] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 676.882168] wlx000f1065113b: authenticate with c8:b3:73:3e:25:d3
[ 677.016733] wlx000f1065113b: send auth to c8:b3:73:3e:25:d3 (try 1/3)
[ 677.018220] wlx000f1065113b: authenticated
[ 682.022063] wlx000f1065113b: aborting authentication with c8:b3:73:3e:25:d3 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 695.632528] wlx000f1065113b: authenticate with c8:b3:73:3e:25:d3
[ 695.905095] wlx000f1065113b: send auth to c8:b3:73:3e:25:d3 (try 1/3)
[ 695.909528] wlx000f1065113b: authenticated
[ 700.910301] wlx000f1065113b: aborting authentication with c8:b3:73:3e:25:d3 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 702.027810] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 703.944948] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 710.977396] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 710.992532] wlx000f1065113b: authenticate with 34:b3:54:22:33:c4
[ 711.126014] wlx000f1065113b: send auth to 34:b3:54:22:33:c4 (try 1/3)
[ 711.127526] wlx000f1065113b: 34:b3:54:22:33:c4 denied authentication (status 13)
[ 727.878608] wlx000f1065113b: authenticate with 34:b3:54:22:33:c4
[ 728.150213] wlx000f1065113b: send auth to 34:b3:54:22:33:c4 (try 1/3)
[ 728.151982] wlx000f1065113b: 34:b3:54:22:33:c4 denied authentication (status 13)
[ 736.029060] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 738.006135] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 852.895280] perf: interrupt took too long (2541 > 2500), lowering kernel.perf_event_max_sample_rate to 78500
[ 1082.962441] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 1123.172094] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 1124.936163] wlx000f1065113b: authenticate with 34:b3:54:22:33:c4
[ 1125.212879] wlx000f1065113b: send auth to 34:b3:54:22:33:c4 (try 1/3)
[ 1125.214343] wlx000f1065113b: 34:b3:54:22:33:c4 denied authentication (status 13)
[ 1140.707955] perf: interrupt took too long (3285 > 3176), lowering kernel.perf_event_max_sample_rate to 60750
[ 1141.997162] wlx000f1065113b: authenticate with 34:b3:54:22:33:c4
[ 1142.273525] wlx000f1065113b: send auth to 34:b3:54:22:33:c4 (try 1/3)
[ 1142.275244] wlx000f1065113b: 34:b3:54:22:33:c4 denied authentication (status 13)
[ 1148.043870] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 1149.957599] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 1393.398604] perf: interrupt took too long (4228 > 4106), lowering kernel.perf_event_max_sample_rate to 47250
[ 1494.966855] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 1812.105948] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 2073.295661] r8169 0000:07:00.0 enp7s0: link down
[ 2083.167248] wlp6s0: deauthenticating from 34:b3:54:22:33:c4 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 2083.183845] IPv6: ADDRCONF(NETDEV_UP): wlp6s0: link is not ready
[ 2087.468141] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 2089.212333] wlx000f1065113b: authenticate with 34:b3:54:22:33:c4
[ 2089.488831] wlx000f1065113b: send auth to 34:b3:54:22:33:c4 (try 1/3)
[ 2089.491693] wlx000f1065113b: 34:b3:54:22:33:c4 denied authentication (status 13)
[ 2106.237287] wlx000f1065113b: authenticate with 34:b3:54:22:33:c4
[ 2106.513877] wlx000f1065113b: send auth to 34:b3:54:22:33:c4 (try 1/3)
[ 2106.515877] wlx000f1065113b: 34:b3:54:22:33:c4 denied authentication (status 13)
[ 2113.086567] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 2114.997507] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 2429.092649] IPv6: ADDRCONF(NETDEV_UP): wlp6s0: link is not ready
[ 2460.010161] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
[ 2603.351932] perf: interrupt took too long (5341 > 5285), lowering kernel.perf_event_max_sample_rate to 37250
[ 2744.109523] IPv6: ADDRCONF(NETDEV_UP): wlp6s0: link is not ready
[ 2777.062023] IPv6: ADDRCONF(NETDEV_UP): wlx000f1065113b: link is not ready
For lsusb:
Code: Select all
Bus 002 Device 002: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
For lsusb -t
Code: Select all
|__ Port 2: Dev 2, If 0, Class=(Defined at Interface level), Driver=rtl8187, 480M
When 'lspci -k' is performed, I can't see the Realtek Wireless Card:
Code: Select all
lspci -k
00:00.0 Host bridge: Intel Corporation Broadwell-U Host Bridge -OPI (rev 09)
Subsystem: Dell Broadwell-U Host Bridge -OPI
Kernel driver in use: bdw_uncore
00:02.0 VGA compatible controller: Intel Corporation HD Graphics 5500 (rev 09)
Subsystem: Dell HD Graphics 5500
Kernel driver in use: i915
Kernel modules: i915
00:03.0 Audio device: Intel Corporation Broadwell-U Audio Controller (rev 09)
Subsystem: Dell Broadwell-U Audio Controller
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.0 USB controller: Intel Corporation Wildcat Point-LP USB xHCI Controller (rev 03)
Subsystem: Dell Wildcat Point-LP USB xHCI Controller
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:16.0 Communication controller: Intel Corporation Wildcat Point-LP MEI Controller #1 (rev 03)
Subsystem: Dell Wildcat Point-LP MEI Controller
Kernel driver in use: mei_me
Kernel modules: mei_me
00:1b.0 Audio device: Intel Corporation Wildcat Point-LP High Definition Audio Controller (rev 03)
Subsystem: Dell Wildcat Point-LP High Definition Audio Controller
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #1 (rev e3)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.2 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #3 (rev e3)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #4 (rev e3)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation Wildcat Point-LP PCI Express Root Port #5 (rev e3)
Kernel driver in use: pcieport
Kernel modules: shpchp
00:1d.0 USB controller: Intel Corporation Wildcat Point-LP USB EHCI Controller (rev 03)
Subsystem: Dell Wildcat Point-LP USB EHCI Controller
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge: Intel Corporation Wildcat Point-LP LPC Controller (rev 03)
Subsystem: Dell Wildcat Point-LP LPC Controller
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller: Intel Corporation Wildcat Point-LP SATA Controller [AHCI Mode] (rev 03)
Subsystem: Dell Wildcat Point-LP SATA Controller [AHCI Mode]
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation Wildcat Point-LP SMBus Controller (rev 03)
Subsystem: Dell Wildcat Point-LP SMBus Controller
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
06:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83)
Subsystem: Intel Corporation Dual Band Wireless AC 3160
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller (rev 07)
Subsystem: Dell RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller
Kernel driver in use: r8169
Kernel modules: r8169
.
For lshw -c network:
Code: Select all
*-network
description: Wireless interface
physical id: 2
bus info: usb@2:2
logical name: wlx000f1065113b
serial: ce:ce:67:f7:35:aa
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=rtl8187 driverversion=4.9.0-3-amd64 firmware=N/A link=no multicast=yes wireless=IEEE 802.11
For iwconfig:
Code: Select all
wlx000f1065113b IEEE 802.11 ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Any idea, or we just have to wait for the bug to be solved?