Scheduled Maintenance: We are aware of an issue with Google, AOL, and Yahoo services as email providers which are blocking new registrations. We are trying to fix the issue and we have several internal and external support tickets in process to resolve the issue. Please see:
viewtopic.php?t=158230
If none of the specific sub-forums seem right for your thread, ask here.
kereberos
Posts: 67 Joined: 2011-05-23 09:12
#1
Post
by kereberos » 2017-03-28 19:24
hi everybody.
i have some error on boot (debian 8 stable).
Code: Select all
[ 6115.005223] ata6: irq_stat 0x00000040, connection status changed
[ 6115.005225] ata6: SError: { CommWake DevExch }
[ 6115.005236] ata6: limiting SATA link speed to 1.5 Gbps
[ 6115.005238] ata6: hard resetting link
[ 6117.232755] ata6: SATA link down (SStatus 1 SControl 310)
[ 6117.232783] ata6: EH complete
[ 6117.239733] ata6: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen
[ 6117.239742] ata6: irq_stat 0x00000040, connection status changed
[ 6117.239746] ata6: SError: { CommWake DevExch }
[ 6117.239763] ata6: limiting SATA link speed to 1.5 Gbps
[ 6117.239768] ata6: hard resetting link
i read a lot about this issue and i saw people say this one is bad hdd or sata cable, but it happened right away and SMART check looking good..
I saw these messages after I changed the file system, I changed the fstab file and the computer did not perform boot afterwards, so I uploaded the system through live usb and changed the fstab file back.
tnx a lot for helping!
bw123
Posts: 4015 Joined: 2011-05-09 06:02
Has thanked: 1 time
Been thanked: 28 times
#2
Post
by bw123 » 2017-03-28 21:50
SMART check looking good..
You have run short and long tests with smartctl with no errors?
resigned by AI ChatGPT
kereberos
Posts: 67 Joined: 2011-05-23 09:12
#3
Post
by kereberos » 2017-03-29 18:29
hi, tnx about your answer
yes, i made a short test and long test.
this is the short test:
Code: Select all
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus SpinPoint M8 (AF)
Device Model: ST1000LM024 HN-M101MBB
Serial Number: S30YJ9HF307022
LU WWN Device Id: 5 0004cf 20cac3e6e
Firmware Version: 2BA30001
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Mar 29 22:15:09 2017 IDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (13080) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 218) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 0
2 Throughput_Performance 0x0026 056 056 000 Old_age Always - 11882
3 Spin_Up_Time 0x0023 092 088 025 Pre-fail Always - 2459
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1543
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 4053
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 147
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1516
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 93
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 048 000 Old_age Always - 32 (Min/Max 11/53)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 3
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 401
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 147
225 Load_Cycle_Count 0x0032 086 086 000 Old_age Always - 151172
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 3747 hours (156 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
01 9f 18 9f 18 f0 18 9f 10:54:18.685 [RESERVED]
00 00 00 00 00 00 00 00 00:00:00.126 NOP [Abort queued commands]
61 00 70 60 3e e3 40 00 00:00:00.131 WRITE FPDMA QUEUED
61 00 00 60 3d e3 40 00 00:00:00.131 WRITE FPDMA QUEUED
61 00 10 b0 bf a5 40 00 00:00:00.131 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4053 -
# 2 Extended offline Aborted by host 90% 4053 -
# 3 Extended offline Completed without error 00% 4050 -
# 4 Short offline Completed without error 00% 3846 -
# 5 Vendor (0x50) Completed without error 00% 3772 -
# 6 Short offline Completed without error 00% 3772 -
# 7 Vendor (0x50) Completed without error 00% 3647 -
# 8 Short offline Completed without error 00% 3647 -
# 9 Vendor (0x50) Completed without error 00% 3419 -
#10 Short offline Completed without error 00% 3419 -
#11 Vendor (0x50) Completed without error 00% 3227 -
#12 Short offline Completed without error 00% 3227 -
#13 Vendor (0x50) Completed without error 00% 3176 -
#14 Short offline Completed without error 00% 3175 -
#15 Vendor (0x50) Completed without error 00% 3091 -
#16 Short offline Completed without error 00% 3091 -
#17 Vendor (0x50) Completed without error 00% 2975 -
#18 Short offline Completed without error 00% 2975 -
#19 Vendor (0x50) Completed without error 00% 2889 -
#20 Short offline Completed without error 00% 2889 -
#21 Vendor (0x50) Completed without error 00% 2818 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Segfault
Posts: 993 Joined: 2005-09-24 12:24
Has thanked: 5 times
Been thanked: 17 times
#4
Post
by Segfault » 2017-03-29 19:02
IMHO dropping to 1.5 Gbit/s indicates bad communication. Have you tried a different SATA port and another SATA cable?
kereberos
Posts: 67 Joined: 2011-05-23 09:12
#5
Post
by kereberos » 2017-03-29 19:12
Segfault wrote: IMHO dropping to 1.5 Gbit/s indicates bad communication. Have you tried a different SATA port and another SATA cable?
hi.
i do not have another SATA port/cable cause its my laptop.
but, if do you think this is the problem i will try to replace these components.
Segfault
Posts: 993 Joined: 2005-09-24 12:24
Has thanked: 5 times
Been thanked: 17 times
#6
Post
by Segfault » 2017-03-29 19:44
There are three components involved to get this error. SATA controller and its port, cable, the control board of hard drive. One of them is failing. In case of laptop there probably is no cable, just the SATA controller, connector and the controller board of the HDD. Re-seating the drive - and inspecting the connectors while the drive is out - may help, too.
Segfault
Posts: 993 Joined: 2005-09-24 12:24
Has thanked: 5 times
Been thanked: 17 times
#8
Post
by Segfault » 2017-03-29 21:23
You are welcome. Please do not use text speak. Some people find text speak when used without a good reason careless and rude. I am one of those people.