Black login screen and cannot startx after Buster installati

Help with issues regarding installation of Debian

Black login screen and cannot startx after Buster installati

Postby skipperx » 2019-08-04 04:34

Hello:

I have been pulling hair for a few days on this and hoping someone can help me sort it out.

It is a fresh install of Buster in an Asus UX31A laptop that is a few years old. It has Intel graphics. I have tried installing Buster with XFCE, Cinnamon, and Mate, one DE at a time and got the same results. Black screen with a blinking cursor on the top left corner. I can go to tty screens and login from command line and try to startx. X fails to start. I have installed firmware-misc-nonfree and intel-microcode and still have the same results. I checked and saw xserver-xorg-video-intel is also there.

Currently, I installed it with Mate and LXDE. Still the same results.

Stretch was running fine on the same machine before.

Here is the information that I thought might be relevant. I would appreciate some help.

Thank you.

lspci -v

Code: Select all
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, fast devsel, latency 0
   Capabilities: [e0] Vendor Specific Information: Len=0c <?>
   Kernel driver in use: ivb_uncore

00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) (prog-if 00 [VGA controller])
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, fast devsel, latency 0, IRQ 26
   Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
   Memory at e0000000 (64-bit, prefetchable) [size=256M]
   I/O ports at f000 [size=64]
   [virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
   Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Capabilities: [d0] Power Management version 2
   Capabilities: [a4] PCI Advanced Features
   Kernel driver in use: i915
   Kernel modules: i915

00:04.0 Signal processing controller: Intel Corporation 3rd Gen Core Processor Thermal Subsystem (rev 09)
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, fast devsel, latency 0, IRQ 255
   Memory at dfe08000 (64-bit, non-prefetchable) [size=32K]
   Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
   Capabilities: [d0] Power Management version 3
   Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) (prog-if 30 [XHCI])
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, medium devsel, latency 0, IRQ 24
   Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
   Capabilities: [70] Power Management version 2
   Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
   Kernel driver in use: xhci_hcd
   Kernel modules: xhci_pci

00:16.0 Communication controller: Intel Corporation 7 Series/C216 Chipset Family MEI Controller #1 (rev 04)
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, fast devsel, latency 0, IRQ 27
   Memory at f7d22000 (64-bit, non-prefetchable) [size=16]
   Capabilities: [50] Power Management version 3
   Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+
   Kernel driver in use: mei_me
   Kernel modules: mei_me

00:1a.0 USB controller: Intel Corporation 7 Series/C216 Chipset Family USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI])
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, medium devsel, latency 0, IRQ 16
   Memory at f7d20000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: [50] Power Management version 2
   Capabilities: [58] Debug port: BAR=1 offset=00a0
   Capabilities: [98] PCI Advanced Features
   Kernel driver in use: ehci-pci
   Kernel modules: ehci_pci

00:1b.0 Audio device: Intel Corporation 7 Series/C216 Chipset Family High Definition Audio Controller (rev 04)
   Subsystem: ASUSTeK Computer Inc. 7 Series/C216 Chipset Family High Definition Audio Controller
   Flags: bus master, fast devsel, latency 0, IRQ 28
   Memory at f7d18000 (64-bit, non-prefetchable) [size=16K]
   Capabilities: [50] Power Management version 2
   Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
   Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
   Capabilities: [100] Virtual Channel
   Capabilities: [130] Root Complex Link
   Kernel driver in use: snd_hda_intel
   Kernel modules: snd_hda_intel

00:1c.0 PCI bridge: Intel Corporation 7 Series/C216 Chipset Family PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0, IRQ 16
   Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
   Capabilities: [40] Express Root Port (Slot+), MSI 00
   Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
   Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Capabilities: [a0] Power Management version 2
   Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) (prog-if 00 [Normal decode])
   Flags: bus master, fast devsel, latency 0, IRQ 17
   Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
   Memory behind bridge: f7c00000-f7cfffff
   Capabilities: [40] Express Root Port (Slot+), MSI 00
   Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
   Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Capabilities: [a0] Power Management version 2
   Kernel driver in use: pcieport

00:1d.0 USB controller: Intel Corporation 7 Series/C216 Chipset Family USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI])
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, medium devsel, latency 0, IRQ 23
   Memory at f7d1f000 (32-bit, non-prefetchable) [size=1K]
   Capabilities: [50] Power Management version 2
   Capabilities: [58] Debug port: BAR=1 offset=00a0
   Capabilities: [98] PCI Advanced Features
   Kernel driver in use: ehci-pci
   Kernel modules: ehci_pci

00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04)
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, medium devsel, latency 0
   Capabilities: [e0] Vendor Specific Information: Len=0c <?>
   Kernel driver in use: lpc_ich
   Kernel modules: lpc_ich

00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0])
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 25
   I/O ports at f0b0 [size=8]
   I/O ports at f0a0 [size=4]
   I/O ports at f090 [size=8]
   I/O ports at f080 [size=4]
   I/O ports at f060 [size=32]
   Memory at f7d1e000 (32-bit, non-prefetchable) [size=2K]
   Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
   Capabilities: [70] Power Management version 3
   Capabilities: [a8] SATA HBA v1.0
   Capabilities: [b0] PCI Advanced Features
   Kernel driver in use: ahci
   Kernel modules: ahci

00:1f.3 SMBus: Intel Corporation 7 Series/C216 Chipset Family SMBus Controller (rev 04)
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: medium devsel, IRQ 18
   Memory at f7d1d000 (64-bit, non-prefetchable) [size=256]
   I/O ports at f040 [size=32]
   Kernel driver in use: i801_smbus
   Kernel modules: i2c_i801

00:1f.6 Signal processing controller: Intel Corporation 7 Series/C210 Series Chipset Family Thermal Management Controller (rev 04)
   Subsystem: ASUSTeK Computer Inc. Zenbook Prime UX31A
   Flags: bus master, fast devsel, latency 0, IRQ 255
   Memory at f7d1c000 (64-bit, non-prefetchable) [size=4K]
   Capabilities: [50] Power Management version 3

02:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24)
   Subsystem: Intel Corporation Centrino Advanced-N 6235 AGN
   Flags: bus master, fast devsel, latency 0, IRQ 29
   Memory at f7c00000 (64-bit, non-prefetchable) [size=8K]
   Capabilities: [c8] Power Management version 3
   Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
   Capabilities: [e0] Express Endpoint, MSI 00
   Capabilities: [100] Advanced Error Reporting
   Capabilities: [140] Device Serial Number c4-85-08-ff-ff-4d-cb-4b
   Kernel driver in use: iwlwifi
   Kernel modules: iwlwifi



Xorg.1.log

Code: Select all
[    82.351]
X.Org X Server 1.20.4
X Protocol Version 11, Revision 0
[    82.352] Build Operating System: Linux 4.9.0-8-amd64 x86_64 Debian
[    82.352] Current Operating System: Linux asus 4.19.0-5-amd64 #1 SMP Debian 4.19.37-5+deb10u1 (2019-07-19) x86_64
[    82.352] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.19.0-5-amd64 root=UUID=8e8fc7d0-f197-4f76-8209-249de3785851 ro quiet
[    82.352] Build Date: 05 March 2019  08:11:12PM
[    82.352] xorg-server 2:1.20.4-1 (https://www.debian.org/support)
[    82.352] Current version of pixman: 0.36.0
[    82.352]    Before reporting problems, check http://wiki.x.org
   to make sure that you have the latest version.
[    82.352] Markers: (--) probed, (**) from config file, (==) default setting,
   (++) from command line, (!!) notice, (II) informational,
   (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    82.353] (==) Log file: "/home/irena/.local/share/xorg/Xorg.1.log", Time: Sat Aug  3 23:55:26 2019
[    82.353] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    82.353] (==) No Layout section.  Using the first Screen section.
[    82.353] (==) No screen section available. Using defaults.
[    82.353] (**) |-->Screen "Default Screen Section" (0)
[    82.353] (**) |   |-->Monitor "<default monitor>"
[    82.354] (==) No monitor specified for screen "Default Screen Section".
   Using a default monitor configuration.
[    82.354] (==) Automatically adding devices
[    82.354] (==) Automatically enabling devices
[    82.354] (==) Automatically adding GPU devices
[    82.354] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    82.354] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    82.354]    Entry deleted from font path.
[    82.354] (==) FontPath set to:
   /usr/share/fonts/X11/misc,
   /usr/share/fonts/X11/100dpi/:unscaled,
   /usr/share/fonts/X11/75dpi/:unscaled,
   /usr/share/fonts/X11/Type1,
   /usr/share/fonts/X11/100dpi,
   /usr/share/fonts/X11/75dpi,
   built-ins
[    82.354] (==) ModulePath set to "/usr/lib/xorg/modules"
[    82.354] (II) The server relies on udev to provide the list of input devices.
   If no devices become available, reconfigure udev or disable AutoAddDevices.
[    82.354] (II) Loader magic: 0x559a5421ce20
[    82.354] (II) Module ABI versions:
[    82.354]    X.Org ANSI C Emulation: 0.4
[    82.354]    X.Org Video Driver: 24.0
[    82.354]    X.Org XInput driver : 24.1
[    82.354]    X.Org Server Extension : 10.0
[    82.355] (++) using VT number 1

[    82.358] (II) systemd-logind: took control of session /org/freedesktop/login1/session/_32
[    82.359] (II) xfree86: Adding drm device (/dev/dri/card0)
[    82.360] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 11 paused 0
[    82.363] (--) PCI:*(0@0:2:0) 8086:0166:1043:1517 rev 9, Mem @ 0xf7800000/4194304, 0xe0000000/268435456, I/O @ 0x0000f000/64, BIOS @ 0x????????/131072
[    82.363] (II) LoadModule: "glx"
[    82.364] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    82.365] (II) Module glx: vendor="X.Org Foundation"
[    82.365]    compiled for 1.20.4, module version = 1.0.0
[    82.365]    ABI class: X.Org Server Extension, version 10.0
[    82.365] (==) Matched modesetting as autoconfigured driver 0
[    82.365] (==) Matched fbdev as autoconfigured driver 1
[    82.365] (==) Matched vesa as autoconfigured driver 2
[    82.365] (==) Assigned the driver to the xf86ConfigLayout
[    82.366] (II) LoadModule: "modesetting"
[    82.366] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[    82.366] (II) Module modesetting: vendor="X.Org Foundation"
[    82.366]    compiled for 1.20.4, module version = 1.20.4
[    82.366]    Module class: X.Org Video Driver
[    82.366]    ABI class: X.Org Video Driver, version 24.0
[    82.366] (II) LoadModule: "fbdev"
[    82.366] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so
[    82.366] (II) Module fbdev: vendor="X.Org Foundation"
[    82.366]    compiled for 1.20.0, module version = 0.5.0
[    82.366]    Module class: X.Org Video Driver
[    82.366]    ABI class: X.Org Video Driver, version 24.0
[    82.366] (II) LoadModule: "vesa"
[    82.366] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[    82.366] (II) Module vesa: vendor="X.Org Foundation"
[    82.366]    compiled for 1.20.1, module version = 2.4.0
[    82.366]    Module class: X.Org Video Driver
[    82.366]    ABI class: X.Org Video Driver, version 24.0
[    82.366] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[    82.366] (II) FBDEV: driver for framebuffer: fbdev
[    82.366] (II) VESA: driver for VESA chipsets: vesa
[    82.367] xf86EnableIOPorts: failed to set IOPL for I/O (Operation not permitted)
[    82.367] (II) modeset(0): using drv /dev/dri/card0
[    82.367] (WW) Falling back to old probe method for fbdev
[    82.367] (II) Loading sub module "fbdevhw"
[    82.367] (II) LoadModule: "fbdevhw"
[    82.367] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so
[    82.367] (II) Module fbdevhw: vendor="X.Org Foundation"
[    82.367]    compiled for 1.20.4, module version = 0.0.2
[    82.367]    ABI class: X.Org Video Driver, version 24.0
[    82.367] (WW) VGA arbiter: cannot open kernel arbiter, no multi-card support
[    82.367] (II) modeset(0): Creating default Display subsection in Screen section
   "Default Screen Section" for depth/fbbpp 24/32
[    82.367] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[    82.367] (==) modeset(0): RGB weight 888
[    82.367] (==) modeset(0): Default visual is TrueColor
[    82.367] (II) Loading sub module "glamoregl"
[    82.367] (II) LoadModule: "glamoregl"
[    82.367] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[    82.370] (II) Module glamoregl: vendor="X.Org Foundation"
[    82.370]    compiled for 1.20.4, module version = 1.0.1
[    82.370]    ABI class: X.Org ANSI C Emulation, version 0.4
[    82.384] (II) modeset(0): glamor X acceleration enabled on Mesa DRI Intel(R) Ivybridge Mobile
[    82.384] (II) modeset(0): glamor initialized
[    82.385] (II) modeset(0): Output eDP-1 has no monitor section
[    82.386] (II) modeset(0): Output VGA-1 has no monitor section
[    82.388] (II) modeset(0): Output HDMI-1 has no monitor section
[    82.388] (II) modeset(0): Output DP-1 has no monitor section
[    82.389] (II) modeset(0): EDID for output eDP-1
[    82.389] (II) modeset(0): Manufacturer: CMN  Model: 1348  Serial#: 0
[    82.389] (II) modeset(0): Year: 2012  Week: 22
[    82.389] (II) modeset(0): EDID Version: 1.4
[    82.389] (II) modeset(0): Digital Display Input
[    82.389] (II) modeset(0): 8 bits per channel
[    82.389] (II) modeset(0): Digital interface is DisplayPort
[    82.389] (II) modeset(0): Max Image Size [cm]: horiz.: 28  vert.: 16
[    82.389] (II) modeset(0): Gamma: 2.20
[    82.389] (II) modeset(0): No DPMS capabilities specified
[    82.389] (II) modeset(0): Supported color encodings: RGB 4:4:4
[    82.389] (II) modeset(0): First detailed timing is preferred mode
[    82.389] (II) modeset(0): Preferred mode is native pixel format and refresh rate
[    82.389] (II) modeset(0): redX: 0.650 redY: 0.338   greenX: 0.329 greenY: 0.608
[    82.389] (II) modeset(0): blueX: 0.148 blueY: 0.047   whiteX: 0.313 whiteY: 0.329
[    82.389] (II) modeset(0): Manufacturer's mask: 0
[    82.389] (II) modeset(0): Supported detailed timing:
[    82.389] (II) modeset(0): clock: 138.8 MHz   Image Size:  282 x 165 mm
[    82.389] (II) modeset(0): h_active: 1920  h_sync: 1966  h_sync_end 1996 h_blank_end 2080 h_border: 0
[    82.389] (II) modeset(0): v_active: 1080  v_sync: 1082  v_sync_end 1086 v_blanking: 1112 v_border: 0
[    82.389] (II) modeset(0): Supported detailed timing:
[    82.389] (II) modeset(0): clock: 92.5 MHz   Image Size:  282 x 165 mm
[    82.389] (II) modeset(0): h_active: 1920  h_sync: 1966  h_sync_end 1996 h_blank_end 2080 h_border: 0
[    82.389] (II) modeset(0): v_active: 1080  v_sync: 1082  v_sync_end 1086 v_blanking: 1112 v_border: 0
[    82.389] (II) modeset(0):  CMN
[    82.389] (II) modeset(0):  N133HSG-F31
[    82.389] (II) modeset(0): EDID (in hex):
[    82.389] (II) modeset(0):    00ffffffffffff000dae481300000000
[    82.389] (II) modeset(0):    16160104a51c107802a705a656549b26
[    82.390] (II) modeset(0):    0c505400000001010101010101010101
[    82.390] (II) modeset(0):    010101010101363680a0703820402e1e
[    82.390] (II) modeset(0):    24001aa510000018242480a070382040
[    82.390] (II) modeset(0):    2e1e24001aa510000018000000fe0043
[    82.390] (II) modeset(0):    4d4e0a202020202020202020000000fe
[    82.390] (II) modeset(0):    004e3133334853472d4633310a200079
[    82.390] (II) modeset(0): Printing probed modes for output eDP-1
[    82.390] (II) modeset(0): Modeline "1920x1080"x60.0  138.78  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (66.7 kHz eP)
[    82.390] (II) modeset(0): Modeline "1920x1080"x119.9  266.50  1920 1944 1960 2000  1080 1081 1084 1111 doublescan +hsync -vsync (133.2 kHz d)
[    82.390] (II) modeset(0): Modeline "1920x1080"x60.0  173.00  1920 2048 2248 2576  1080 1083 1088 1120 -hsync +vsync (67.2 kHz d)
[    82.390] (II) modeset(0): Modeline "1920x1080"x59.9  138.50  1920 1968 2000 2080  1080 1083 1088 1111 +hsync -vsync (66.6 kHz d)
[    82.390] (II) modeset(0): Modeline "1920x1080"x40.0   92.52  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (44.5 kHz e)
[    82.390] (II) modeset(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 -hsync +vsync (65.3 kHz d)
[    82.390] (II) modeset(0): Modeline "1680x1050"x59.9  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz d)
[    82.390] (II) modeset(0): Modeline "1600x1024"x60.2  103.12  1600 1600 1656 1664  1024 1024 1029 1030 +hsync +vsync (62.0 kHz d)
[    82.390] (II) modeset(0): Modeline "1400x1050"x60.0  122.00  1400 1488 1640 1880  1050 1052 1064 1082 +hsync +vsync (64.9 kHz d)
[    82.390] (II) modeset(0): Modeline "1600x900"x120.0  246.00  1600 1728 1900 2200  900 901 904 932 doublescan -hsync +vsync (111.8 kHz d)
[    82.390] (II) modeset(0): Modeline "1600x900"x119.9  186.50  1600 1624 1640 1680  900 901 904 926 doublescan +hsync -vsync (111.0 kHz d)
[    82.390] (II) modeset(0): Modeline "1600x900"x59.9  118.25  1600 1696 1856 2112  900 903 908 934 -hsync +vsync (56.0 kHz d)
[    82.390] (II) modeset(0): Modeline "1600x900"x59.8   97.50  1600 1648 1680 1760  900 903 908 926 +hsync -vsync (55.4 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz d)
[    82.390] (II) modeset(0): Modeline "1440x900"x59.9  106.50  1440 1520 1672 1904  900 903 909 934 -hsync +vsync (55.9 kHz d)
[    82.390] (II) modeset(0): Modeline "1400x900"x60.0  103.50  1400 1480 1624 1848  900 903 913 934 -hsync +vsync (56.0 kHz d)
[    82.390] (II) modeset(0): Modeline "1400x900"x59.9   86.50  1400 1448 1480 1560  900 903 913 926 +hsync -vsync (55.4 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz d)
[    82.390] (II) modeset(0): Modeline "1440x810"x120.0  198.12  1440 1548 1704 1968  810 811 814 839 doublescan -hsync +vsync (100.7 kHz d)
[    82.390] (II) modeset(0): Modeline "1440x810"x119.9  151.88  1440 1464 1480 1520  810 811 814 833 doublescan +hsync -vsync (99.9 kHz d)
[    82.390] (II) modeset(0): Modeline "1368x768"x59.9   85.25  1368 1440 1576 1784  768 771 781 798 -hsync +vsync (47.8 kHz d)
[    82.390] (II) modeset(0): Modeline "1368x768"x59.9   72.25  1368 1416 1448 1528  768 771 781 790 +hsync -vsync (47.3 kHz d)
[    82.390] (II) modeset(0): Modeline "1360x768"x59.8   84.75  1360 1432 1568 1776  768 771 781 798 -hsync +vsync (47.7 kHz d)
[    82.390] (II) modeset(0): Modeline "1360x768"x60.0   72.00  1360 1408 1440 1520  768 771 781 790 +hsync -vsync (47.4 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x800"x120.0  174.25  1280 1380 1516 1752  800 801 804 829 doublescan -hsync +vsync (99.5 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x800"x119.9  134.25  1280 1304 1320 1360  800 801 804 823 doublescan +hsync -vsync (98.7 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x800"x59.8   83.50  1280 1352 1480 1680  800 803 809 831 -hsync +vsync (49.7 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x800"x59.9   71.00  1280 1328 1360 1440  800 803 809 823 +hsync -vsync (49.3 kHz d)
[    82.390] (II) modeset(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 -hsync +vsync (53.7 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x720"x120.0  156.12  1280 1376 1512 1744  720 721 724 746 doublescan -hsync +vsync (89.5 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x720"x120.0  120.75  1280 1304 1320 1360  720 721 724 740 doublescan +hsync -vsync (88.8 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x720"x59.9   74.50  1280 1344 1472 1664  720 723 728 748 -hsync +vsync (44.8 kHz d)
[    82.390] (II) modeset(0): Modeline "1280x720"x59.7   63.75  1280 1328 1360 1440  720 723 728 741 +hsync -vsync (44.3 kHz d)
[    82.390] (II) modeset(0): Modeline "1024x768"x120.1  133.47  1024 1100 1212 1400  768 768 770 794 doublescan -hsync +vsync (95.3 kHz d)
[    82.390] (II) modeset(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz d)
[    82.390] (II) modeset(0): Modeline "960x720"x120.0  117.00  960 1024 1128 1300  720 720 722 750 doublescan -hsync +vsync (90.0 kHz d)
[    82.390] (II) modeset(0): Modeline "928x696"x120.1  109.15  928 976 1088 1264  696 696 698 719 doublescan -hsync +vsync (86.4 kHz d)
[    82.390] (II) modeset(0): Modeline "896x672"x120.0  102.40  896 960 1060 1224  672 672 674 697 doublescan -hsync +vsync (83.7 kHz d)
[    82.390] (II) modeset(0): Modeline "1024x576"x119.9   98.50  1024 1092 1200 1376  576 577 580 597 doublescan -hsync +vsync (71.6 kHz d)
[    82.390] (II) modeset(0): Modeline "1024x576"x119.9   78.38  1024 1048 1064 1104  576 577 580 592 doublescan +hsync -vsync (71.0 kHz d)
[    82.390] (II) modeset(0): Modeline "1024x576"x59.9   46.50  1024 1064 1160 1296  576 579 584 599 -hsync +vsync (35.9 kHz d)
[    82.390] (II) modeset(0): Modeline "1024x576"x59.8   42.00  1024 1072 1104 1184  576 579 584 593 +hsync -vsync (35.5 kHz d)
[    82.390] (II) modeset(0): Modeline "960x600"x119.9   96.62  960 1028 1128 1296  600 601 604 622 doublescan -hsync +vsync (74.6 kHz d)
[    82.390] (II) modeset(0): Modeline "960x600"x120.0   77.00  960 984 1000 1040  600 601 604 617 doublescan +hsync -vsync (74.0 kHz d)
[    82.390] (II) modeset(0): Modeline "960x540"x119.9   86.50  960 1024 1124 1288  540 541 544 560 doublescan -hsync +vsync (67.2 kHz d)
[    82.390] (II) modeset(0): Modeline "960x540"x120.0   69.25  960 984 1000 1040  540 541 544 555 doublescan +hsync -vsync (66.6 kHz d)
[    82.390] (II) modeset(0): Modeline "960x540"x59.6   40.75  960 992 1088 1216  540 543 548 562 -hsync +vsync (33.5 kHz d)
[    82.390] (II) modeset(0): Modeline "960x540"x59.8   37.25  960 1008 1040 1120  540 543 548 556 +hsync -vsync (33.3 kHz d)
[    82.390] (II) modeset(0): Modeline "800x600"x120.0   81.00  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (75.0 kHz d)
[    82.390] (II) modeset(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz d)
[    82.390] (II) modeset(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz d)
[    82.390] (II) modeset(0): Modeline "840x525"x120.0   73.12  840 892 980 1120  525 526 529 544 doublescan -hsync +vsync (65.3 kHz d)
[    82.390] (II) modeset(0): Modeline "840x525"x119.8   59.50  840 864 880 920  525 526 529 540 doublescan +hsync -vsync (64.7 kHz d)
[    82.390] (II) modeset(0): Modeline "864x486"x59.9   32.50  864 888 968 1072  486 489 494 506 -hsync +vsync (30.3 kHz d)
[    82.390] (II) modeset(0): Modeline "864x486"x59.6   30.50  864 912 944 1024  486 489 494 500 +hsync -vsync (29.8 kHz d)
[    82.390] (II) modeset(0): Modeline "800x512"x120.3   51.56  800 800 828 832  512 512 514 515 doublescan +hsync +vsync (62.0 kHz d)
[    82.390] (II) modeset(0): Modeline "700x525"x120.0   61.00  700 744 820 940  525 526 532 541 doublescan +hsync +vsync (64.9 kHz d)
[    82.390] (II) modeset(0): Modeline "800x450"x119.9   59.12  800 848 928 1056  450 451 454 467 doublescan -hsync +vsync (56.0 kHz d)
[    82.390] (II) modeset(0): Modeline "800x450"x119.6   48.75  800 824 840 880  450 451 454 463 doublescan +hsync -vsync (55.4 kHz d)
[    82.390] (II) modeset(0): Modeline "640x512"x120.0   54.00  640 664 720 844  512 512 514 533 doublescan +hsync +vsync (64.0 kHz d)
[    82.390] (II) modeset(0): Modeline "720x450"x119.8   53.25  720 760 836 952  450 451 454 467 doublescan -hsync +vsync (55.9 kHz d)
[    82.390] (II) modeset(0): Modeline "700x450"x119.9   51.75  700 740 812 924  450 451 456 467 doublescan -hsync +vsync (56.0 kHz d)
[    82.390] (II) modeset(0): Modeline "700x450"x119.8   43.25  700 724 740 780  450 451 456 463 doublescan +hsync -vsync (55.4 kHz d)
[    82.390] (II) modeset(0): Modeline "640x480"x120.0   54.00  640 688 744 900  480 480 482 500 doublescan +hsync +vsync (60.0 kHz d)
[    82.390] (II) modeset(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz d)
[    82.390] (II) modeset(0): Modeline "720x405"x59.5   22.50  720 744 808 896  405 408 413 422 -hsync +vsync (25.1 kHz d)
[    82.390] (II) modeset(0): Modeline "720x405"x59.0   21.75  720 768 800 880  405 408 413 419 +hsync -vsync (24.7 kHz d)
[    82.390] (II) modeset(0): Modeline "684x384"x119.8   42.62  684 720 788 892  384 385 390 399 doublescan -hsync +vsync (47.8 kHz d)
[    82.390] (II) modeset(0): Modeline "684x384"x119.7   36.12  684 708 724 764  384 385 390 395 doublescan +hsync -vsync (47.3 kHz d)
[    82.390] (II) modeset(0): Modeline "680x384"x119.6   42.38  680 716 784 888  384 385 390 399 doublescan -hsync +vsync (47.7 kHz d)
[    82.390] (II) modeset(0): Modeline "680x384"x119.9   36.00  680 704 720 760  384 385 390 395 doublescan +hsync -vsync (47.4 kHz d)
[    82.390] (II) modeset(0): Modeline "640x400"x119.8   41.75  640 676 740 840  400 401 404 415 doublescan -hsync +vsync (49.7 kHz d)
[    82.390] (II) modeset(0): Modeline "640x400"x120.0   35.50  640 664 680 720  400 401 404 411 doublescan +hsync -vsync (49.3 kHz d)
[    82.390] (II) modeset(0): Modeline "576x432"x120.1   40.81  576 608 668 760  432 432 434 447 doublescan -hsync +vsync (53.7 kHz d)
[    82.390] (II) modeset(0): Modeline "640x360"x119.7   37.25  640 672 736 832  360 361 364 374 doublescan -hsync +vsync (44.8 kHz d)
[    82.390] (II) modeset(0): Modeline "640x360"x119.7   31.88  640 664 680 720  360 361 364 370 doublescan +hsync -vsync (44.3 kHz d)
[    82.390] (II) modeset(0): Modeline "640x360"x59.8   18.00  640 664 720 800  360 363 368 376 -hsync +vsync (22.5 kHz d)
[    82.390] (II) modeset(0): Modeline "640x360"x59.3   17.75  640 688 720 800  360 363 368 374 +hsync -vsync (22.2 kHz d)
[    82.390] (II) modeset(0): Modeline "512x384"x120.0   32.50  512 524 592 672  384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)
[    82.390] (II) modeset(0): Modeline "512x288"x120.0   23.25  512 532 580 648  288 289 292 299 doublescan -hsync +vsync (35.9 kHz d)
[    82.390] (II) modeset(0): Modeline "512x288"x119.8   21.00  512 536 552 592  288 289 292 296 doublescan +hsync -vsync (35.5 kHz d)
[    82.390] (II) modeset(0): Modeline "480x270"x119.3   20.38  480 496 544 608  270 271 274 281 doublescan -hsync +vsync (33.5 kHz d)
[    82.390] (II) modeset(0): Modeline "480x270"x119.6   18.62  480 504 520 560  270 271 274 278 doublescan +hsync -vsync (33.3 kHz d)
[    82.390] (II) modeset(0): Modeline "400x300"x120.6   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)
[    82.390] (II) modeset(0): Modeline "400x300"x112.7   18.00  400 412 448 512  300 300 301 312 doublescan +hsync +vsync (35.2 kHz d)
[    82.390] (II) modeset(0): Modeline "432x243"x119.8   16.25  432 444 484 536  243 244 247 253 doublescan -hsync +vsync (30.3 kHz d)
[    82.390] (II) modeset(0): Modeline "432x243"x119.1   15.25  432 456 472 512  243 244 247 250 doublescan +hsync -vsync (29.8 kHz d)
[    82.390] (II) modeset(0): Modeline "320x240"x120.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)
[    82.390] (II) modeset(0): Modeline "360x202"x119.0   11.25  360 372 404 448  202 204 206 211 doublescan -hsync +vsync (25.1 kHz d)
[    82.390] (II) modeset(0): Modeline "360x202"x118.3   10.88  360 384 400 440  202 204 206 209 doublescan +hsync -vsync (24.7 kHz d)
[    82.390] (II) modeset(0): Modeline "320x180"x119.7    9.00  320 332 360 400  180 181 184 188 doublescan -hsync +vsync (22.5 kHz d)
[    82.390] (II) modeset(0): Modeline "320x180"x118.6    8.88  320 344 360 400  180 181 184 187 doublescan +hsync -vsync (22.2 kHz d)
[    82.392] (II) modeset(0): EDID for output VGA-1
[    82.393] (II) modeset(0): EDID for output HDMI-1
[    82.393] (II) modeset(0): EDID for output DP-1
[    82.393] (II) modeset(0): Output eDP-1 connected
[    82.393] (II) modeset(0): Output VGA-1 disconnected
[    82.393] (II) modeset(0): Output HDMI-1 disconnected
[    82.393] (II) modeset(0): Output DP-1 disconnected
[    82.393] (II) modeset(0): Using exact sizes for initial modes
[    82.393] (II) modeset(0): Output eDP-1 using initial mode 1920x1080 +0+0
[    82.393] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[    82.393] (==) modeset(0): DPI set to (96, 96)
[    82.393] (II) Loading sub module "fb"
[    82.393] (II) LoadModule: "fb"
[    82.393] (II) Loading /usr/lib/xorg/modules/libfb.so
[    82.394] (II) Module fb: vendor="X.Org Foundation"
[    82.394]    compiled for 1.20.4, module version = 1.0.0
[    82.394]    ABI class: X.Org ANSI C Emulation, version 0.4
[    82.394] (II) UnloadModule: "fbdev"
[    82.394] (II) Unloading fbdev
[    82.394] (II) UnloadSubModule: "fbdevhw"
[    82.394] (II) Unloading fbdevhw
[    82.394] (II) UnloadModule: "vesa"
[    82.394] (II) Unloading vesa
[    82.465] (==) modeset(0): Backing store enabled
[    82.466] (==) modeset(0): Silken mouse enabled
[    82.515] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc.
[    82.515] (==) modeset(0): DPMS enabled
[    82.516] (II) modeset(0): [DRI2] Setup complete
[    82.516] (II) modeset(0): [DRI2]   DRI driver: i965
[    82.516] (II) modeset(0): [DRI2]   VDPAU driver: i965
[    82.516] (II) Initializing extension Generic Event Extension
[    82.516] (II) Initializing extension SHAPE
[    82.517] (II) Initializing extension MIT-SHM
[    82.517] (II) Initializing extension XInputExtension
[    82.517] (II) Initializing extension XTEST
[    82.517] (II) Initializing extension BIG-REQUESTS
[    82.518] (II) Initializing extension SYNC
[    82.518] (II) Initializing extension XKEYBOARD
[    82.518] (II) Initializing extension XC-MISC
[    82.518] (II) Initializing extension SECURITY
[    82.518] (II) Initializing extension XFIXES
[    82.519] (II) Initializing extension RENDER
[    82.519] (II) Initializing extension RANDR
[    82.519] (II) Initializing extension COMPOSITE
[    82.519] (II) Initializing extension DAMAGE
[    82.520] (II) Initializing extension MIT-SCREEN-SAVER
[    82.520] (II) Initializing extension DOUBLE-BUFFER
[    82.520] (II) Initializing extension RECORD
[    82.520] (II) Initializing extension DPMS
[    82.520] (II) Initializing extension Present
[    82.521] (II) Initializing extension DRI3
[    82.521] (II) Initializing extension X-Resource
[    82.521] (II) Initializing extension XVideo
[    82.521] (II) Initializing extension XVideo-MotionCompensation
[    82.521] (II) Initializing extension SELinux
[    82.521] (II) SELinux: Disabled on system
[    82.521] (II) Initializing extension GLX
[    82.528] (II) AIGLX: Loaded and initialized i965
[    82.528] (II) GLX: Initialized DRI2 GL provider for screen 0
[    82.528] (II) Initializing extension XFree86-VidModeExtension
[    82.528] (II) Initializing extension XFree86-DGA
[    82.528] (II) Initializing extension XFree86-DRI
[    82.528] (II) Initializing extension DRI2
[    82.530] (II) modeset(0): Damage tracking initialized
[    82.530] (II) modeset(0): Setting screen physical size to 508 x 285
[    82.577] (II) config/udev: Adding input device Asus Wireless Radio Control (/dev/input/event8)
[    82.577] (**) Asus Wireless Radio Control: Applying InputClass "libinput keyboard catchall"
[    82.577] (II) LoadModule: "libinput"
[    82.578] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    82.581] (II) Module libinput: vendor="X.Org Foundation"
[    82.581]    compiled for 1.20.4, module version = 0.28.2
[    82.581]    Module class: X.Org XInput Driver
[    82.581]    ABI class: X.Org XInput driver, version 24.1
[    82.581] (II) Using input driver 'libinput' for 'Asus Wireless Radio Control'
[    82.583] (II) systemd-logind: got fd for /dev/input/event8 13:72 fd 20 paused 0
[    82.583] (**) Asus Wireless Radio Control: always reports core events
[    82.584] (**) Option "Device" "/dev/input/event8"
[    82.584] (**) Option "_source" "server/udev"
[    82.588] (II) event8  - Asus Wireless Radio Control: is tagged by udev as: Keyboard
[    82.588] (II) event8  - Asus Wireless Radio Control: device is a keyboard
[    82.588] (II) event8  - Asus Wireless Radio Control: device removed
[    82.588] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/ATK4001:00/input/input16/event8"
[    82.588] (II) XINPUT: Adding extended input device "Asus Wireless Radio Control" (type: KEYBOARD, id 6)
[    82.588] (**) Option "xkb_model" "pc105"
[    82.588] (**) Option "xkb_layout" "us"
[    82.590] (II) event8  - Asus Wireless Radio Control: is tagged by udev as: Keyboard
[    82.590] (II) event8  - Asus Wireless Radio Control: device is a keyboard
[    82.591] (II) config/udev: Adding input device Video Bus (/dev/input/event4)
[    82.591] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[    82.591] (II) Using input driver 'libinput' for 'Video Bus'
[    82.593] (II) systemd-logind: got fd for /dev/input/event4 13:68 fd 23 paused 0
[    82.593] (**) Video Bus: always reports core events
[    82.593] (**) Option "Device" "/dev/input/event4"
[    82.593] (**) Option "_source" "server/udev"
[    82.595] (II) event4  - Video Bus: is tagged by udev as: Keyboard
[    82.595] (II) event4  - Video Bus: device is a keyboard
[    82.595] (II) event4  - Video Bus: device removed
[    82.595] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input12/event4"
[    82.595] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[    82.595] (**) Option "xkb_model" "pc105"
[    82.595] (**) Option "xkb_layout" "us"
[    82.598] (II) event4  - Video Bus: is tagged by udev as: Keyboard
[    82.598] (II) event4  - Video Bus: device is a keyboard
[    82.599] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[    82.599] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    82.599] (II) Using input driver 'libinput' for 'Power Button'
[    82.601] (II) systemd-logind: got fd for /dev/input/event2 13:66 fd 24 paused 0
[    82.601] (**) Power Button: always reports core events
[    82.601] (**) Option "Device" "/dev/input/event2"
[    82.601] (**) Option "_source" "server/udev"
[    82.602] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    82.602] (II) event2  - Power Button: device is a keyboard
[    82.602] (II) event2  - Power Button: device removed
[    82.602] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6/event2"
[    82.602] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[    82.602] (**) Option "xkb_model" "pc105"
[    82.602] (**) Option "xkb_layout" "us"
[    82.604] (II) event2  - Power Button: is tagged by udev as: Keyboard
[    82.604] (II) event2  - Power Button: device is a keyboard
[    82.605] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[    82.605] (II) No input driver specified, ignoring this device.
[    82.605] (II) This device may have been added with another device file.
[    82.606] (II) config/udev: Adding input device Sleep Button (/dev/input/event3)
[    82.606] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[    82.606] (II) Using input driver 'libinput' for 'Sleep Button'
[    82.608] (II) systemd-logind: got fd for /dev/input/event3 13:67 fd 25 paused 0
[    82.608] (**) Sleep Button: always reports core events
[    82.608] (**) Option "Device" "/dev/input/event3"
[    82.608] (**) Option "_source" "server/udev"
[    82.609] (II) event3  - Sleep Button: is tagged by udev as: Keyboard
[    82.609] (II) event3  - Sleep Button: device is a keyboard
[    82.609] (II) event3  - Sleep Button: device removed
[    82.610] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input7/event3"
[    82.610] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[    82.610] (**) Option "xkb_model" "pc105"
[    82.610] (**) Option "xkb_layout" "us"
[    82.611] (II) event3  - Sleep Button: is tagged by udev as: Keyboard
[    82.611] (II) event3  - Sleep Button: device is a keyboard
[    82.613] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7903-16v07_Test6 (/dev/input/event12)
[    82.613] (**) eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: Applying InputClass "libinput touchscreen catchall"
[    82.613] (II) Using input driver 'libinput' for 'eGalax Inc. eGalaxTouch EXC7903-16v07_Test6'
[    82.674] (II) systemd-logind: got fd for /dev/input/event12 13:76 fd 26 paused 0
[    82.674] (**) eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: always reports core events
[    82.674] (**) Option "Device" "/dev/input/event12"
[    82.674] (**) Option "_source" "server/udev"
[    82.678] (II) event12 - eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: is tagged by udev as: Touchscreen
[    82.679] (II) event12 - eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: device is a touch device
[    82.679] (II) event12 - eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: device removed
[    82.679] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/0003:0EEF:7908.0001/input/input22/event12"
[    82.679] (II) XINPUT: Adding extended input device "eGalax Inc. eGalaxTouch EXC7903-16v07_Test6" (type: TOUCHSCREEN, id 10)
[    82.679] (**) Option "AccelerationScheme" "none"
[    82.679] (**) eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: (accel) selected scheme none/0
[    82.679] (**) eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: (accel) acceleration factor: 2.000
[    82.679] (**) eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: (accel) acceleration threshold: 4
[    82.682] (II) event12 - eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: is tagged by udev as: Touchscreen
[    82.682] (II) event12 - eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: device is a touch device
[    82.683] (II) config/udev: Adding input device eGalax Inc. eGalaxTouch EXC7903-16v07_Test6 (/dev/input/mouse1)
[    82.683] (II) No input driver specified, ignoring this device.
[    82.683] (II) This device may have been added with another device file.
[    82.683] (II) config/udev: Adding input device HDA Intel PCH Headphone (/dev/input/event7)
[    82.683] (II) No input driver specified, ignoring this device.
[    82.683] (II) This device may have been added with another device file.
[    82.683] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event11)
[    82.683] (II) No input driver specified, ignoring this device.
[    82.683] (II) This device may have been added with another device file.
[    82.684] (II) config/udev: Adding input device USB2.0 HD UVC WebCam: USB2.0 HD (/dev/input/event10)
[    82.684] (**) USB2.0 HD UVC WebCam: USB2.0 HD: Applying InputClass "libinput keyboard catchall"
[    82.684] (II) Using input driver 'libinput' for 'USB2.0 HD UVC WebCam: USB2.0 HD'
[    82.687] (II) systemd-logind: got fd for /dev/input/event10 13:74 fd 27 paused 0
[    82.687] (**) USB2.0 HD UVC WebCam: USB2.0 HD: always reports core events
[    82.687] (**) Option "Device" "/dev/input/event10"
[    82.687] (**) Option "_source" "server/udev"
[    82.691] (II) event10 - USB2.0 HD UVC WebCam: USB2.0 HD: is tagged by udev as: Keyboard
[    82.691] (II) event10 - USB2.0 HD UVC WebCam: USB2.0 HD: device is a keyboard
[    82.691] (II) event10 - USB2.0 HD UVC WebCam: USB2.0 HD: device removed
[    82.691] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.5/4-1.5:1.0/input/input18/event10"
[    82.691] (II) XINPUT: Adding extended input device "USB2.0 HD UVC WebCam: USB2.0 HD" (type: KEYBOARD, id 11)
[    82.691] (**) Option "xkb_model" "pc105"
[    82.691] (**) Option "xkb_layout" "us"
[    82.695] (II) event10 - USB2.0 HD UVC WebCam: USB2.0 HD: is tagged by udev as: Keyboard
[    82.695] (II) event10 - USB2.0 HD UVC WebCam: USB2.0 HD: device is a keyboard
[    82.696] (II) config/udev: Adding input device Asus WMI hotkeys (/dev/input/event6)
[    82.696] (**) Asus WMI hotkeys: Applying InputClass "libinput keyboard catchall"
[    82.696] (II) Using input driver 'libinput' for 'Asus WMI hotkeys'
[    82.698] (II) systemd-logind: got fd for /dev/input/event6 13:70 fd 28 paused 0
[    82.698] (**) Asus WMI hotkeys: always reports core events
[    82.698] (**) Option "Device" "/dev/input/event6"
[    82.698] (**) Option "_source" "server/udev"
[    82.700] (II) event6  - Asus WMI hotkeys: is tagged by udev as: Keyboard
[    82.700] (II) event6  - Asus WMI hotkeys: device is a keyboard
[    82.700] (II) event6  - Asus WMI hotkeys: device removed
[    82.700] (**) Option "config_info" "udev:/sys/devices/platform/asus-nb-wmi/input/input19/event6"
[    82.700] (II) XINPUT: Adding extended input device "Asus WMI hotkeys" (type: KEYBOARD, id 12)
[    82.700] (**) Option "xkb_model" "pc105"
[    82.700] (**) Option "xkb_layout" "us"
[    82.701] (II) event6  - Asus WMI hotkeys: is tagged by udev as: Keyboard
[    82.701] (II) event6  - Asus WMI hotkeys: device is a keyboard
[    82.702] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[    82.702] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[    82.702] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[    82.704] (II) systemd-logind: got fd for /dev/input/event0 13:64 fd 29 paused 0
[    82.705] (**) AT Translated Set 2 keyboard: always reports core events
[    82.705] (**) Option "Device" "/dev/input/event0"
[    82.705] (**) Option "_source" "server/udev"
[    82.706] (II) event0  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[    82.706] (II) event0  - AT Translated Set 2 keyboard: device is a keyboard
[    82.706] (II) event0  - AT Translated Set 2 keyboard: device removed
[    82.706] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[    82.706] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 13)
[    82.706] (**) Option "xkb_model" "pc105"
[    82.706] (**) Option "xkb_layout" "us"
[    82.707] (II) event0  - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[    82.707] (II) event0  - AT Translated Set 2 keyboard: device is a keyboard
[    82.708] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/event5)
[    82.708] (**) ETPS/2 Elantech Touchpad: Applying InputClass "libinput touchpad catchall"
[    82.708] (II) Using input driver 'libinput' for 'ETPS/2 Elantech Touchpad'
[    82.710] (II) systemd-logind: got fd for /dev/input/event5 13:69 fd 30 paused 0
[    82.710] (**) ETPS/2 Elantech Touchpad: always reports core events
[    82.710] (**) Option "Device" "/dev/input/event5"
[    82.710] (**) Option "_source" "server/udev"
[    82.711] (II) event5  - ETPS/2 Elantech Touchpad: is tagged by udev as: Touchpad
[    82.713] (II) event5  - ETPS/2 Elantech Touchpad: device is a touchpad
[    82.713] (II) event5  - ETPS/2 Elantech Touchpad: device removed
[    82.713] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio4/input/input11/event5"
[    82.713] (II) XINPUT: Adding extended input device "ETPS/2 Elantech Touchpad" (type: TOUCHPAD, id 14)
[    82.714] (**) Option "AccelerationScheme" "none"
[    82.714] (**) ETPS/2 Elantech Touchpad: (accel) selected scheme none/0
[    82.714] (**) ETPS/2 Elantech Touchpad: (accel) acceleration factor: 2.000
[    82.714] (**) ETPS/2 Elantech Touchpad: (accel) acceleration threshold: 4
[    82.715] (II) event5  - ETPS/2 Elantech Touchpad: is tagged by udev as: Touchpad
[    82.716] (II) event5  - ETPS/2 Elantech Touchpad: device is a touchpad
[    82.716] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/mouse0)
[    82.716] (II) No input driver specified, ignoring this device.
[    82.716] (II) This device may have been added with another device file.
[    82.717] (II) config/udev: Adding input device PC Speaker (/dev/input/event9)
[    82.717] (II) No input driver specified, ignoring this device.
[    82.717] (II) This device may have been added with another device file.
[    82.721] (EE) modeset(0): failed to set mode: Invalid argument
[    82.981] (II) modeset(0): EDID vendor "CMN", prod id 4936
[    82.981] (II) modeset(0): Printing DDC gathered Modelines:
[    82.981] (II) modeset(0): Modeline "1920x1080"x0.0  138.78  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (66.7 kHz eP)
[    82.981] (II) modeset(0): Modeline "1920x1080"x0.0   92.52  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (44.5 kHz e)
[    82.986] (II) modeset(0): EDID vendor "CMN", prod id 4936
[    82.986] (II) modeset(0): Printing DDC gathered Modelines:
[    82.986] (II) modeset(0): Modeline "1920x1080"x0.0  138.78  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (66.7 kHz eP)
[    82.986] (II) modeset(0): Modeline "1920x1080"x0.0   92.52  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (44.5 kHz e)
[    82.992] (II) modeset(0): EDID vendor "CMN", prod id 4936
[    82.992] (II) modeset(0): Printing DDC gathered Modelines:
[    82.992] (II) modeset(0): Modeline "1920x1080"x0.0  138.78  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (66.7 kHz eP)
[    82.992] (II) modeset(0): Modeline "1920x1080"x0.0   92.52  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (44.5 kHz e)
[    82.997] (II) modeset(0): EDID vendor "CMN", prod id 4936
[    82.997] (II) modeset(0): Printing DDC gathered Modelines:
[    82.997] (II) modeset(0): Modeline "1920x1080"x0.0  138.78  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (66.7 kHz eP)
[    82.997] (II) modeset(0): Modeline "1920x1080"x0.0   92.52  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (44.5 kHz e)
[    83.473] (II) modeset(0): EDID vendor "CMN", prod id 4936
[    83.473] (II) modeset(0): Printing DDC gathered Modelines:
[    83.473] (II) modeset(0): Modeline "1920x1080"x0.0  138.78  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (66.7 kHz eP)
[    83.473] (II) modeset(0): Modeline "1920x1080"x0.0   92.52  1920 1966 1996 2080  1080 1082 1086 1112 -hsync -vsync (44.5 kHz e)
[   123.610] (**) Option "fd" "20"
[   123.610] (II) event8  - Asus Wireless Radio Control: device removed
[   123.612] (**) Option "fd" "23"
[   123.612] (II) event4  - Video Bus: device removed
[   123.613] (**) Option "fd" "24"
[   123.613] (II) event2  - Power Button: device removed
[   123.614] (**) Option "fd" "25"
[   123.614] (II) event3  - Sleep Button: device removed
[   123.614] (**) Option "fd" "26"
[   123.614] (II) event12 - eGalax Inc. eGalaxTouch EXC7903-16v07_Test6: device removed
[   123.615] (**) Option "fd" "27"
[   123.615] (II) event10 - USB2.0 HD UVC WebCam: USB2.0 HD: device removed
[   123.616] (**) Option "fd" "28"
[   123.616] (II) event6  - Asus WMI hotkeys: device removed
[   123.617] (**) Option "fd" "29"
[   123.617] (II) event0  - AT Translated Set 2 keyboard: device removed
[   123.617] (**) Option "fd" "30"
[   123.617] (II) event5  - ETPS/2 Elantech Touchpad: device removed
[   123.617] (II) AIGLX: Suspending AIGLX clients for VT switch
[   123.678] (II) systemd-logind: got pause for 13:64
[   123.678] (II) systemd-logind: got pause for 13:68
[   123.678] (II) systemd-logind: got pause for 13:74
[   123.678] (II) systemd-logind: got pause for 13:69
[   123.678] (II) systemd-logind: got pause for 13:67
[   123.678] (II) systemd-logind: got pause for 13:66
[   123.678] (II) systemd-logind: got pause for 226:0
[   123.678] (II) systemd-logind: got pause for 13:72
[   123.678] (II) systemd-logind: got pause for 13:76
[   123.678] (II) systemd-logind: got pause for 13:70
[   127.086] (II) systemd-logind: got resume for 13:64
[   127.118] (II) systemd-logind: got resume for 13:68
[   127.142] (II) systemd-logind: got resume for 13:74
[   127.166] (II) systemd-logind: got resume for 13:69
[   127.190] (II) systemd-logind: got resume for 13:67
[   127.214] (II) systemd-logind: got resume for 13:66
[   127.214] (II) systemd-logind: got resume for 226:0
[   127.214] (II) AIGLX: Resuming AIGLX clients after VT switch
[   127.215] (EE) modeset(0): failed to set mode: Invalid argument
[   127.215] (EE)
Fatal server error:
[   127.215] (EE) EnterVT failed for screen 0
[   127.215] (EE)
[   127.215] (EE)
Please consult the The X.Org Foundation support
    at http://wiki.x.org
 for help.
[   127.215] (EE) Please also check the log file at "/home/irena/.local/share/xorg/Xorg.1.log" for additional information.
[   127.215] (EE)
[   127.215] (II) AIGLX: Suspending AIGLX clients for VT switch
[   127.291] (EE) Server terminated with error (1). Closing log file.


lightdm.conf

Code: Select all
#
# General configuration
#
# start-default-seat = True to always start one seat if none are defined in the configuration
# greeter-user = User to run greeter as
# minimum-display-number = Minimum display number to use for X servers
# minimum-vt = First VT to run displays on
# lock-memory = True to prevent memory from being paged to disk
# user-authority-in-system-dir = True if session authority should be in the system location
# guest-account-script = Script to be run to setup guest account
# logind-check-graphical = True to on start seats that are marked as graphical by logind
# log-directory = Directory to log information to
# run-directory = Directory to put running state in
# cache-directory = Directory to cache to
# sessions-directory = Directory to find sessions
# remote-sessions-directory = Directory to find remote sessions
# greeters-directory = Directory to find greeters
# backup-logs = True to move add a .old suffix to old log files when opening new ones
# dbus-service = True if LightDM provides a D-Bus service to control it
#
[LightDM]
#start-default-seat=true
#greeter-user=lightdm
#minimum-display-number=0
#minimum-vt=7
#lock-memory=true
#user-authority-in-system-dir=false
#guest-account-script=guest-account
#logind-check-graphical=false
#log-directory=/var/log/lightdm
#run-directory=/var/run/lightdm
#cache-directory=/var/cache/lightdm
#sessions-directory=/usr/share/lightdm/sessions:/usr/share/xsessions:/usr/share/wayland-sessions
#remote-sessions-directory=/usr/share/lightdm/remote-sessions
#greeters-directory=$XDG_DATA_DIRS/lightdm/greeters:$XDG_DATA_DIRS/xgreeters
#backup-logs=true
#dbus-service=true

#
# Seat configuration
#
# Seat configuration is matched against the seat name glob in the section, for example:
# [Seat:*] matches all seats and is applied first.
# [Seat:seat0] matches the seat named "seat0".
# [Seat:seat-thin-client*] matches all seats that have names that start with "seat-thin-client".
#
# type = Seat type (local, xremote, unity)
# pam-service = PAM service to use for login
# pam-autologin-service = PAM service to use for autologin
# pam-greeter-service = PAM service to use for greeters
# xserver-backend = X backend to use (mir)
# xserver-command = X server command to run (can also contain arguments e.g. X -special-option)
# xmir-command = Xmir server command to run (can also contain arguments e.g. Xmir -special-option)
# xserver-config = Config file to pass to X server
# xserver-layout = Layout to pass to X server
# xserver-allow-tcp = True if TCP/IP connections are allowed to this X server
# xserver-share = True if the X server is shared for both greeter and session
# xserver-hostname = Hostname of X server (only for type=xremote)
# xserver-display-number = Display number of X server (only for type=xremote)
# xdmcp-manager = XDMCP manager to connect to (implies xserver-allow-tcp=true)
# xdmcp-port = XDMCP UDP/IP port to communicate on
# xdmcp-key = Authentication key to use for XDM-AUTHENTICATION-1 (stored in keys.conf)
# unity-compositor-command = Unity compositor command to run (can also contain arguments e.g. unity-system-compositor -special-option)
# unity-compositor-timeout = Number of seconds to wait for compositor to start
# greeter-session = Session to load for greeter
# greeter-hide-users = True to hide the user list
# greeter-allow-guest = True if the greeter should show a guest login option
# greeter-show-manual-login = True if the greeter should offer a manual login option
# greeter-show-remote-login = True if the greeter should offer a remote login option
# user-session = Session to load for users
# allow-user-switching = True if allowed to switch users
# allow-guest = True if guest login is allowed
# guest-session = Session to load for guests (overrides user-session)
# session-wrapper = Wrapper script to run session with
# greeter-wrapper = Wrapper script to run greeter with
# guest-wrapper = Wrapper script to run guest sessions with
# display-setup-script = Script to run when starting a greeter session (runs as root)
# display-stopped-script = Script to run after stopping the display server (runs as root)
# greeter-setup-script = Script to run when starting a greeter (runs as root)
# session-setup-script = Script to run when starting a user session (runs as root)
# session-cleanup-script = Script to run when quitting a user session (runs as root)
# autologin-guest = True to log in as guest by default
# autologin-user = User to log in with by default (overrides autologin-guest)
# autologin-user-timeout = Number of seconds to wait before loading default user
# autologin-session = Session to load for automatic login (overrides user-session)
# autologin-in-background = True if autologin session should not be immediately activated
# exit-on-failure = True if the daemon should exit if this seat fails
#
[Seat:*]
#type=local
#pam-service=lightdm
#pam-autologin-service=lightdm-autologin
#pam-greeter-service=lightdm-greeter
#xserver-backend=
#xserver-command=X
#xmir-command=Xmir
#xserver-config=
#xserver-layout=
#xserver-allow-tcp=false
#xserver-share=true
#xserver-hostname=
#xserver-display-number=
#xdmcp-manager=
#xdmcp-port=177
#xdmcp-key=
#unity-compositor-command=unity-system-compositor
#unity-compositor-timeout=60
greeter-session=lightdm-gtk-greeter
#greeter-hide-users=false
#greeter-allow-guest=true
#greeter-show-manual-login=false
#greeter-show-remote-login=true
user-session=mate
#allow-user-switching=true
#allow-guest=true
#guest-session=
#session-wrapper=lightdm-session
#greeter-wrapper=
#guest-wrapper=
#display-setup-script=
#display-stopped-script=
#greeter-setup-script=
#session-setup-script=
#session-cleanup-script=
#autologin-guest=false
#autologin-user=
#autologin-user-timeout=0
#autologin-in-background=false
#autologin-session=
#exit-on-failure=false

#
# XDMCP Server configuration
#
# enabled = True if XDMCP connections should be allowed
# port = UDP/IP port to listen for connections on
# listen-address = Host/address to listen for XDMCP connections (use all addresses if not present)
# key = Authentication key to use for XDM-AUTHENTICATION-1 or blank to not use authentication (stored in keys.conf)
# hostname = Hostname to report to XDMCP clients (defaults to system hostname if unset)
#
# The authentication key is a 56 bit DES key specified in hex as 0xnnnnnnnnnnnnnn.  Alternatively
# it can be a word and the first 7 characters are used as the key.
#
[XDMCPServer]
#enabled=false
#port=177
#listen-address=
#key=
#hostname=

#
# VNC Server configuration
#
# enabled = True if VNC connections should be allowed
# command = Command to run Xvnc server with
# port = TCP/IP port to listen for connections on
# listen-address = Host/address to listen for VNC connections (use all addresses if not present)
# width = Width of display to use
# height = Height of display to use
# depth = Color depth of display to use
#
[VNCServer]
#enabled=false
#command=Xvnc
#port=5900
#listen-address=
#width=1024
#height=768
#depth=8
skipperx
 
Posts: 214
Joined: 2009-03-01 17:41
Location: Toronto

Re: Black login screen and cannot startx after Buster instal

Postby Dai_trying » 2019-08-04 07:07

I have had a similar problem with intel graphics on Buster, you could try the solution that worked for me in this post and to add to that post, the xorg.conf.new might actually be in root folder (/root/xorg.conf.new) and not your current folder
Dai_trying
 
Posts: 793
Joined: 2016-01-07 12:25

[SOLVED]Black login screen and cannot startx after Buster in

Postby skipperx » 2019-08-04 13:27

@Dai_trying

Thank you very much. Your solution worked. You saved my weekend.
skipperx
 
Posts: 214
Joined: 2009-03-01 17:41
Location: Toronto

Re: Black login screen and cannot startx after Buster instal

Postby Head_on_a_Stick » 2019-08-04 15:27

@OP or @Dai_trying: would it be possible to see the full X.org configuration file?

There was a similar problem over on the Arch forums that was solved by using the Intel DDX driver instead of the modesetting driver and I would be interested to know if the auto-generated file does this.
Don't break DebianHow to report bugs

SharpBang GNU/Linux — a pre-configured Openbox/Tint2 desktop running on Debian stable
User avatar
Head_on_a_Stick
 
Posts: 10613
Joined: 2014-06-01 17:46
Location: /dev/chair

Re: Black login screen and cannot startx after Buster instal

Postby skipperx » 2019-08-04 18:06

I did not change grub for no modesetting. My grub settings are

Code: Select all
GRUB_TIMEOUT=1
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
GRUB_CMDLINE_LINUX_DEFAULT="quiet"
GRUB_CMDLINE_LINUX=""


Here is the xorg.conf

Code: Select all
Section "ServerLayout"
   Identifier     "X.org Configured"
   Screen      0  "Screen0" 0 0
   InputDevice    "Mouse0" "CorePointer"
   InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
   ModulePath   "/usr/lib/xorg/modules"
   FontPath     "/usr/share/fonts/X11/misc"
   FontPath     "/usr/share/fonts/X11/cyrillic"
   FontPath     "/usr/share/fonts/X11/100dpi/:unscaled"
   FontPath     "/usr/share/fonts/X11/75dpi/:unscaled"
   FontPath     "/usr/share/fonts/X11/Type1"
   FontPath     "/usr/share/fonts/X11/100dpi"
   FontPath     "/usr/share/fonts/X11/75dpi"
   FontPath     "built-ins"
EndSection

Section "Module"
   Load  "glx"
EndSection

Section "InputDevice"
   Identifier  "Keyboard0"
   Driver      "kbd"
EndSection

Section "InputDevice"
   Identifier  "Mouse0"
   Driver      "mouse"
   Option       "Protocol" "auto"
   Option       "Device" "/dev/input/mice"
   Option       "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
   Identifier   "Monitor0"
   VendorName   "Monitor Vendor"
   ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "Accel"                 # [<bool>]
        #Option     "AccelMethod"           # <str>
        #Option     "Backlight"             # <str>
        #Option     "CustomEDID"            # <str>
        #Option     "DRI"                   # <str>
        #Option     "Present"               # [<bool>]
        #Option     "ColorKey"              # <i>
        #Option     "VideoKey"              # <i>
        #Option     "Tiling"                # [<bool>]
        #Option     "LinearFramebuffer"     # [<bool>]
        #Option     "HWRotation"            # [<bool>]
        #Option     "VSync"                 # [<bool>]
        #Option     "PageFlip"              # [<bool>]
        #Option     "SwapbuffersWait"       # [<bool>]
        #Option     "TripleBuffer"          # [<bool>]
        #Option     "XvPreferOverlay"       # [<bool>]
        #Option     "HotPlug"               # [<bool>]
        #Option     "ReprobeOutputs"        # [<bool>]
        #Option     "XvMC"                  # [<bool>]
        #Option     "ZaphodHeads"           # <str>
        #Option     "VirtualHeads"          # <i>
        #Option     "TearFree"              # [<bool>]
        #Option     "PerCrtcPixmaps"        # [<bool>]
        #Option     "FallbackDebug"         # [<bool>]
        #Option     "DebugFlushBatches"     # [<bool>]
        #Option     "DebugFlushCaches"      # [<bool>]
        #Option     "DebugWait"             # [<bool>]
        #Option     "BufferCache"           # [<bool>]
   Identifier  "Card0"
   Driver      "intel"
   BusID       "PCI:0:2:0"
EndSection

Section "Screen"
   Identifier "Screen0"
   Device     "Card0"
   Monitor    "Monitor0"
   SubSection "Display"
      Viewport   0 0
      Depth     1
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     4
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     8
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     15
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     16
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     24
   EndSubSection
EndSection
skipperx
 
Posts: 214
Joined: 2009-03-01 17:41
Location: Toronto

Re: Black login screen and cannot startx after Buster instal

Postby Dai_trying » 2019-08-04 18:13

I'm on a different machine right now but will post my xorg.conf when I get to the other one (if it is also wanted)
Dai_trying
 
Posts: 793
Joined: 2016-01-07 12:25

Re: Black login screen and cannot startx after Buster instal

Postby Head_on_a_Stick » 2019-08-04 19:31

Thanks!

@skipperx, does your graphical desktop still work if you replace the contents of the X.org configuration file with this stanza by itself?
Code: Select all
Section "Device"
   Identifier "Card0"
   Driver "intel"
   BusID "PCI:0:2:0"
EndSection

@Dai_trying, if you could also try a skimmed-down version and report back that would be fantastic.
Don't break DebianHow to report bugs

SharpBang GNU/Linux — a pre-configured Openbox/Tint2 desktop running on Debian stable
User avatar
Head_on_a_Stick
 
Posts: 10613
Joined: 2014-06-01 17:46
Location: /dev/chair

Re: Black login screen and cannot startx after Buster instal

Postby Dai_trying » 2019-08-04 20:07

My xorg.conf:
Code: Select all
Section "ServerLayout"
   Identifier     "X.org Configured"
   Screen      0  "Screen0" 0 0
   InputDevice    "Mouse0" "CorePointer"
   InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
   ModulePath   "/usr/lib/xorg/modules"
   FontPath     "/usr/share/fonts/X11/misc"
   FontPath     "/usr/share/fonts/X11/cyrillic"
   FontPath     "/usr/share/fonts/X11/100dpi/:unscaled"
   FontPath     "/usr/share/fonts/X11/75dpi/:unscaled"
   FontPath     "/usr/share/fonts/X11/Type1"
   FontPath     "/usr/share/fonts/X11/100dpi"
   FontPath     "/usr/share/fonts/X11/75dpi"
   FontPath     "built-ins"
EndSection

Section "Module"
   Load  "glx"
EndSection

Section "InputDevice"
   Identifier  "Keyboard0"
   Driver      "kbd"
EndSection

Section "InputDevice"
   Identifier  "Mouse0"
   Driver      "mouse"
   Option       "Protocol" "auto"
   Option       "Device" "/dev/input/mice"
   Option       "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
   Identifier   "Monitor0"
   VendorName   "Monitor Vendor"
   ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "Accel"                 # [<bool>]
        #Option     "AccelMethod"           # <str>
        #Option     "Backlight"             # <str>
        #Option     "CustomEDID"            # <str>
        #Option     "DRI"                   # <str>
        #Option     "Present"               # [<bool>]
        #Option     "ColorKey"              # <i>
        #Option     "VideoKey"              # <i>
        #Option     "Tiling"                # [<bool>]
        #Option     "LinearFramebuffer"     # [<bool>]
        #Option     "HWRotation"            # [<bool>]
        #Option     "VSync"                 # [<bool>]
        #Option     "PageFlip"              # [<bool>]
        #Option     "SwapbuffersWait"       # [<bool>]
        #Option     "TripleBuffer"          # [<bool>]
        #Option     "XvPreferOverlay"       # [<bool>]
        #Option     "HotPlug"               # [<bool>]
        #Option     "ReprobeOutputs"        # [<bool>]
        #Option     "XvMC"                  # [<bool>]
        #Option     "ZaphodHeads"           # <str>
        #Option     "VirtualHeads"          # <i>
        #Option     "TearFree"              # [<bool>]
        #Option     "PerCrtcPixmaps"        # [<bool>]
        #Option     "FallbackDebug"         # [<bool>]
        #Option     "DebugFlushBatches"     # [<bool>]
        #Option     "DebugFlushCaches"      # [<bool>]
        #Option     "DebugWait"             # [<bool>]
        #Option     "BufferCache"           # [<bool>]
   Identifier  "Card0"
   Driver      "intel"
   BusID       "PCI:0:2:0"
EndSection

Section "Screen"
   Identifier "Screen0"
   Device     "Card0"
   Monitor    "Monitor0"
   SubSection "Display"
      Viewport   0 0
      Depth     1
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     4
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     8
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     15
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     16
   EndSubSection
   SubSection "Display"
      Viewport   0 0
      Depth     24
   EndSubSection
EndSection


Just going to test the skimmed version now and will report back.

EDIT: Yes that worked fine, I'm just going to reboot now without an xorg.conf file just to test if this error is still occuring (i can't remember if there has been any kernel updates since my install) and will report that too.

EDIT #2: The problem does still exist and so placed the skimmed xorg.conf file back and restarted lightdm and everything rosy. :D
Dai_trying
 
Posts: 793
Joined: 2016-01-07 12:25

Re: Black login screen and cannot startx after Buster instal

Postby skipperx » 2019-08-05 01:34

Yes, the skimmed xorg.conf still does the job and I am keeping it.

Thank you.
skipperx
 
Posts: 214
Joined: 2009-03-01 17:41
Location: Toronto

Re: Black login screen and cannot startx after Buster instal

Postby Head_on_a_Stick » 2019-08-05 14:32

OK, thanks folks.

This problem is caused by the modesetting DDX driver and so a bug should be reported against the xserver-xorg-core package.

I can't do this myself because I've switched to AMD hardware so if either of you two could open one it would help improve the quality of the stable release.
Don't break DebianHow to report bugs

SharpBang GNU/Linux — a pre-configured Openbox/Tint2 desktop running on Debian stable
User avatar
Head_on_a_Stick
 
Posts: 10613
Joined: 2014-06-01 17:46
Location: /dev/chair

Re: Black login screen and cannot startx after Buster instal

Postby Dai_trying » 2019-08-05 21:01

I had previously reported this as a bug against the kernel as it happened to me after a kernel update although I don't recall if the xserver-xorg-core package was also updated at that time, I have sent an update to that and will wait to see if it can be changed or I need to submit a new bug report.
Dai_trying
 
Posts: 793
Joined: 2016-01-07 12:25

Re: Black login screen and cannot startx after Buster instal

Postby ratrace » 2019-08-11 20:40

Hello,

today i tried to upgrade my system from stretch with xfce to buster with xfce and i'm having the same problem. After the installation finishes and the system starting to reboot, i can't see anything but a black screen with a blinking cursor.

My system is a i386 pentium d, with motherboard asus P5L-MX. I don't have additional graphic card, only what the motherboard has.

I tried the procedure with the new xorg.conf file, but unfortunately after the last command "sudo service lightdm start" the problem remains the same.

I also found this bug report, which i'm not sure if it is relevant and if it is safe to do that.

I saw in a previous post of mine that i had a similar problem with GUI, when i upgraded to stretch. Today when i'm logging in as a root or as a user and i'm typing startx, i can see GUI but it has no icons in the xfce menus. I tried to open xfce-screenshooter but i can't.

Any suggestion what should i do?

Thank you
ratrace
 
Posts: 16
Joined: 2015-04-23 07:52
Location: Athens, Greece

Re: Black login screen and cannot startx after Buster instal

Postby Head_on_a_Stick » 2019-08-18 17:35

ratrace wrote:I tried the procedure with the new xorg.conf file, but unfortunately after the last command "sudo service lightdm start" the problem remains the same.

Do you have an Intel graphics card and is the xserver-xorg-video-intel package installed?

ratrace wrote:when i'm logging in as a root or as a user and i'm typing startx

Don't run startx as root. Ever.

Probably best to reset the permissions in $HOME:
Code: Select all
# chown -R $user:$user /home/$user # replace $user with the actual user name
Don't break DebianHow to report bugs

SharpBang GNU/Linux — a pre-configured Openbox/Tint2 desktop running on Debian stable
User avatar
Head_on_a_Stick
 
Posts: 10613
Joined: 2014-06-01 17:46
Location: /dev/chair


Return to Installation

Who is online

Users browsing this forum: No registered users and 10 guests

fashionable