[Solved] External hard disk disconnects under load with a HP t620 running Debian 12

Need help with peripherals or devices?
Post Reply
Message
Author
marqozzz
Posts: 5
Joined: 2024-10-02 21:15

[Solved] External hard disk disconnects under load with a HP t620 running Debian 12

#1 Post by marqozzz »

Hello, I have debian installed on HP t620. Recently I've replaced the external SSD drive by WDC WD20 EFZX-68AWUN0 mount on sdb1 with encryption
/dev/mapper/luks-dbe75eaf-bafd-49b6-b15f-d83844dc6624
On that disk I have NAS folder where is loaded backup from another machine. When disk is loaded with lot of data (21:27 in log below) then I start to have issue with it. Firstly I was thinking that it was due to high temperature, but in reality temperature of external drive is between 40 and 50 degrees. Here is log I have:

Code: Select all

20:31 Device: /dev/sdb [SAT], no ATA CHECK POWER STATUS support, ignoring -n Directive smartd
20:31 kvm: support for 'kvm_amd' disabled by bios
21:27 xhci_hcd 0000:00:10.0: xHCI host controller not responding, assume dead
21:27 xhci_hcd 0000:00:10.0: HC died; cleaning up
21:27 I/O error, dev sdb, sector 753811912 op 0x1:(WRITE) flags 0x800 phys_seg 12 prio class 2
........
21:27 Buffer I/O error on device dm-0, logical block 94222137
21:27 EXT4-fs (dm-0): I/O error while writing superblock
21:27 Failed unmounting NAS.mount - /NAS.
21:27 Device luks-dbe75eaf-bafd-49b6-b15f-d83844dc6624 is still in use.
21:27 Failed to deactivate: Device or resource busy
21:27 EXT4-fs error (device dm-0): ext4_journal_check_start:83: comm smbd: Detected aborted journal
I hope this issue can be resolved with forum help.
Last edited by marqozzz on 2024-10-21 09:47, edited 1 time in total.
Top
Aki
Global Moderator
Global Moderator
Posts: 4036
Joined: 2014-07-20 18:12
Location: Europe
Has thanked: 112 times
Been thanked: 532 times

Re: logs from debian12 at HP t620

#2 Post by Aki »

Hello,

Welcome to the forum.

It is probably an hardware issue of your hard disk.

You may check the heath status of your disk using smartctl command.

Please rename the subject of the first topic to make it more informative, as: “External hard disk disconnects under load with a HP t620 running Debian 12”
⢀⣴⠾⠻⢶⣦⠀
⣾⠁⢠⠒⠀⣿⡁ Debian - The universal operating system
⢿⡄⠘⠷⠚⠋⠀ https://www.debian.org
⠈⠳⣄⠀
Top
marqozzz
Posts: 5
Joined: 2024-10-02 21:15

External hard disk disconnects under load with a HP t620 running Debian 12

#3 Post by marqozzz »

Thank you.
On the previous disk I have 1-2 times per month issue with "Buffer I/O error on dev sdb" so I decided to replace it with this one Western Digital dedicated for NAS purposes. Booth disks are connected via external adapter Rhino 3.5” USB3.0 https://natec-zone.com/product/rhino-sata-3-5

This is an output form smartctl:

Code: Select all

smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.0-25-amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD20EFZX-68AWUN0
Serial Number:    WD-WXA2D21N7A3Y
LU WWN Device Id: 5 0014ee 2bef7c374
Firmware Version: 81.00B81
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      3.5 inches
Device is:        Not in smartctl database 7.3/5319
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Oct  3 09:19:20 2024 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                (20220) seconds.
Offline data collection
capabilities:                    (0x11) SMART execute Offline immediate.
                                        No Auto Offline data collection support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        No Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 218) minutes.
SCT capabilities:              (0x303d) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   210   202   021    Pre-fail  Always       -       2458
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       868
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       450
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       7
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       3
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       1885
194 Temperature_Celsius     0x0022   099   084   000    Old_age   Always       -       48
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

Selective Self-tests/Logging not supported
Top
Aki
Global Moderator
Global Moderator
Posts: 4036
Joined: 2014-07-20 18:12
Location: Europe
Has thanked: 112 times
Been thanked: 532 times

Re: External hard disk disconnects under load with a HP t620 running Debian 12

#4 Post by Aki »

Hello,

The disk looks OK.

I assume that the transfer rate between the computer and the drive (via the USB 3 interface) should not be too high, so the drive load should not be a problem.

I would check the USB-SATA interface, the USB connection cable and especially the external power supply (change the case and the power supply).

Then I would connect the drive to a different USB port on the computer (not using an USB hub).

Reading a full system log when disk errors occur might provide further clues.

Hope this helps.
⢀⣴⠾⠻⢶⣦⠀
⣾⠁⢠⠒⠀⣿⡁ Debian - The universal operating system
⢿⡄⠘⠷⠚⠋⠀ https://www.debian.org
⠈⠳⣄⠀
Top
marqozzz
Posts: 5
Joined: 2024-10-02 21:15

Re: External hard disk disconnects under load with a HP t620 running Debian 12

#5 Post by marqozzz »

I'm attaching the log - part1

Code: Select all

[    0.000000] Linux version 6.1.0-25-amd64 (debian-kernel@lists.debian.org) (gcc-12 (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP PREEMPT_DYNAMIC Debian 6.1.106-3 (2024-08-26)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-6.1.0-25-amd64 root=UUID=3126d402-493e-49fe-94e8-b977da24a4a4 ro quiet
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000009c8c9fff] usable
[    0.000000] BIOS-e820: [mem 0x000000009c8ca000-0x000000009c8f9fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000009c8fa000-0x000000009c927fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000009c928000-0x000000009ca1ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000009ca20000-0x000000009e068fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000009e069000-0x000000009e0affff] type 20
[    0.000000] BIOS-e820: [mem 0x000000009e0b0000-0x000000009e0b0fff] usable
[    0.000000] BIOS-e820: [mem 0x000000009e0b1000-0x000000009e0b8fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000009e0b9000-0x000000009e214fff] usable
[    0.000000] BIOS-e820: [mem 0x000000009e215000-0x000000009e8a7fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000009e8a8000-0x000000009e8effff] usable
[    0.000000] BIOS-e820: [mem 0x000000009e8f0000-0x000000009eff0fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000009eff1000-0x000000009effffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed40000-0x00000000fed44fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed8ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100001000-0x000000023effffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.31 by American Megatrends
[    0.000000] efi: ESRT=0x9e067c98 ACPI=0x9c912000 ACPI 2.0=0x9c912000 SMBIOS=0xf04c0 MOKvar=0x9dc3b000
[    0.000000] secureboot: Secure boot disabled
[    0.000000] SMBIOS 2.8 present.
[    0.000000] DMI: Hewlett-Packard HP t620 Quad Core TC/21B4, BIOS L40 v02.19 02/19/2019
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1497.270 MHz processor
[    0.001988] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.001998] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.002023] last_pfn = 0x23f000 max_arch_pfn = 0x400000000
[    0.002569] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT
[    0.002858] e820: update [mem 0x9f000000-0xffffffff] usable ==> reserved
[    0.002881] last_pfn = 0x9f000 max_arch_pfn = 0x400000000
[    0.014694] found SMP MP-table at [mem 0x000fd6a0-0x000fd6af]
[    0.014739] esrt: Reserving ESRT space from 0x000000009e067c98 to 0x000000009e067cd0.
[    0.015004] Using GB pages for direct mapping
[    0.018095] RAMDISK: [mem 0x342d9000-0x36163fff]
[    0.018112] ACPI: Early table checksum verification disabled
[    0.018120] ACPI: RSDP 0x000000009C912000 000024 (v02 HPQOEM)
[    0.018130] ACPI: XSDT 0x000000009C912088 000094 (v01 HPQOEM SLIC-CPC 01072009 AMI  00010013)
[    0.018146] ACPI: FACP 0x000000009C9201E8 00010C (v05 HPQOEM SLIC-CPC 01072009 AMI  00010013)
[    0.018159] ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has valid Length but zero Address: 0x0000000000000000/0x1 (20220331/tbfadt-615)
[    0.018173] ACPI: DSDT 0x000000009C9121B0 00E032 (v02 HPQOEM SLIC-CPC 00000000 INTL 20051117)
[    0.018184] ACPI: FACS 0x000000009CA15080 000040
[    0.018193] ACPI: APIC 0x000000009C9202F8 00007E (v03 HPQOEM SLIC-CPC 01072009 AMI  00010013)
[    0.018204] ACPI: FPDT 0x000000009C920378 000044 (v01 HPQOEM SLIC-CPC 01072009 AMI  00010013)
[    0.018214] ACPI: MCFG 0x000000009C9203C0 00003C (v01 HPQOEM SLIC-CPC 01072009 MSFT 00010013)
[    0.018224] ACPI: MSDM 0x000000009C920400 000055 (v03 HPQOEM SLIC-CPC 01072009 AMI  00010013)
[    0.018235] ACPI: HPET 0x000000009C920458 000038 (v01 HPQOEM SLIC-CPC 01072009 AMI  00000005)
[    0.018245] ACPI: BGRT 0x000000009C920490 000038 (v00 HPQOEM SLIC-CPC 01072009 AMI  00010013)
[    0.018255] ACPI: SSDT 0x000000009C9204C8 000B10 (v01 AMD    AGESA    00000001 AMD  00000001)
[    0.018265] ACPI: SSDT 0x000000009C920FD8 0046B7 (v02 AMD    AGESA    00000002 MSFT 04000000)
[    0.018275] ACPI: CRAT 0x000000009C925690 0003A8 (v01 AMD    AGESA    00000001 AMD  00000001)
[    0.018285] ACPI: DBGP 0x000000009C925A38 000034 (v01 HPQOEM SLIC-CPC 01072009 AMI  00010013)
[    0.018295] ACPI: SSDT 0x000000009C925A70 000849 (v01 HPQOEM SLIC-CPC 00000001 MSFT 03000001)
[    0.018306] ACPI: SSDT 0x000000009C9262C0 00042D (v01 AMD    CPMXPRES 00000001 INTL 20051117)
[    0.018316] ACPI: SSDT 0x000000009C9266F0 0010E8 (v01 AMD    CPMCMN   00000001 INTL 20051117)
[    0.018325] ACPI: Reserving FACP table memory at [mem 0x9c9201e8-0x9c9202f3]
[    0.018332] ACPI: Reserving DSDT table memory at [mem 0x9c9121b0-0x9c9201e1]
[    0.018338] ACPI: Reserving FACS table memory at [mem 0x9ca15080-0x9ca150bf]
[    0.018344] ACPI: Reserving APIC table memory at [mem 0x9c9202f8-0x9c920375]
[    0.018349] ACPI: Reserving FPDT table memory at [mem 0x9c920378-0x9c9203bb]
[    0.018355] ACPI: Reserving MCFG table memory at [mem 0x9c9203c0-0x9c9203fb]
[    0.018360] ACPI: Reserving MSDM table memory at [mem 0x9c920400-0x9c920454]
[    0.018366] ACPI: Reserving HPET table memory at [mem 0x9c920458-0x9c92048f]
[    0.018371] ACPI: Reserving BGRT table memory at [mem 0x9c920490-0x9c9204c7]
[    0.018382] ACPI: Reserving SSDT table memory at [mem 0x9c9204c8-0x9c920fd7]
[    0.018388] ACPI: Reserving SSDT table memory at [mem 0x9c920fd8-0x9c92568e]
[    0.018393] ACPI: Reserving CRAT table memory at [mem 0x9c925690-0x9c925a37]
[    0.018399] ACPI: Reserving DBGP table memory at [mem 0x9c925a38-0x9c925a6b]
[    0.018404] ACPI: Reserving SSDT table memory at [mem 0x9c925a70-0x9c9262b8]
[    0.018410] ACPI: Reserving SSDT table memory at [mem 0x9c9262c0-0x9c9266ec]
[    0.018415] ACPI: Reserving SSDT table memory at [mem 0x9c9266f0-0x9c9277d7]
[    0.018553] No NUMA configuration found
[    0.018556] Faking a node at [mem 0x0000000000000000-0x000000023effffff]
[    0.018589] NODE_DATA(0) allocated [mem 0x23efd1000-0x23effbfff]
[    0.019671] Zone ranges:
[    0.019674]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.019680]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.019684]   Normal   [mem 0x0000000100000000-0x000000023effffff]
[    0.019689]   Device   empty
[    0.019692] Movable zone start for each node
[    0.019699] Early memory node ranges
[    0.019700]   node   0: [mem 0x0000000000001000-0x000000000009ffff]
[    0.019704]   node   0: [mem 0x0000000000100000-0x000000009c8c9fff]
[    0.019708]   node   0: [mem 0x000000009e0b0000-0x000000009e0b0fff]
[    0.019711]   node   0: [mem 0x000000009e0b9000-0x000000009e214fff]
[    0.019714]   node   0: [mem 0x000000009e8a8000-0x000000009e8effff]
[    0.019717]   node   0: [mem 0x000000009eff1000-0x000000009effffff]
[    0.019720]   node   0: [mem 0x0000000100001000-0x000000023effffff]
[    0.019727] Initmem setup node 0 [mem 0x0000000000001000-0x000000023effffff]
[    0.019743] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.019851] On node 0, zone DMA: 96 pages in unavailable ranges
[    0.035955] On node 0, zone DMA32: 6118 pages in unavailable ranges
[    0.035980] On node 0, zone DMA32: 8 pages in unavailable ranges
[    0.036056] On node 0, zone DMA32: 1683 pages in unavailable ranges
[    0.036136] On node 0, zone DMA32: 1793 pages in unavailable ranges
[    0.038194] On node 0, zone Normal: 4097 pages in unavailable ranges
[    0.038388] On node 0, zone Normal: 4096 pages in unavailable ranges
[    0.038497] ACPI: PM-Timer IO Port: 0x808
[    0.038516] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.038534] IOAPIC[0]: apic_id 5, version 33, address 0xfec00000, GSI 0-23
[    0.038544] IOAPIC[1]: apic_id 6, version 33, address 0xfec01000, GSI 24-55
[    0.038551] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.038557] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.038568] ACPI: Using ACPI (MADT) for SMP configuration information
[    0.038571] ACPI: HPET id: 0x10228210 base: 0xfed00000
[    0.038623] e820: update [mem 0x90c21000-0x90c33fff] usable ==> reserved
[    0.038658] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.038785] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.038794] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.038803] PM: hibernation: Registered nosave memory: [mem 0x90c21000-0x90c33fff]
[    0.038811] PM: hibernation: Registered nosave memory: [mem 0x9c8ca000-0x9c8f9fff]
[    0.038814] PM: hibernation: Registered nosave memory: [mem 0x9c8fa000-0x9c927fff]
[    0.038817] PM: hibernation: Registered nosave memory: [mem 0x9c928000-0x9ca1ffff]
[    0.038819] PM: hibernation: Registered nosave memory: [mem 0x9ca20000-0x9e068fff]
[    0.038822] PM: hibernation: Registered nosave memory: [mem 0x9e069000-0x9e0affff]
[    0.038830] PM: hibernation: Registered nosave memory: [mem 0x9e0b1000-0x9e0b8fff]
[    0.038839] PM: hibernation: Registered nosave memory: [mem 0x9e215000-0x9e8a7fff]
[    0.038847] PM: hibernation: Registered nosave memory: [mem 0x9e8f0000-0x9eff0fff]
[    0.038856] PM: hibernation: Registered nosave memory: [mem 0x9f000000-0xfebfffff]
[    0.038859] PM: hibernation: Registered nosave memory: [mem 0xfec00000-0xfec01fff]
[    0.038862] PM: hibernation: Registered nosave memory: [mem 0xfec02000-0xfec0ffff]
[    0.038864] PM: hibernation: Registered nosave memory: [mem 0xfec10000-0xfec10fff]
[    0.038867] PM: hibernation: Registered nosave memory: [mem 0xfec11000-0xfecfffff]
[    0.038870] PM: hibernation: Registered nosave memory: [mem 0xfed00000-0xfed00fff]
[    0.038872] PM: hibernation: Registered nosave memory: [mem 0xfed01000-0xfed3ffff]
[    0.038875] PM: hibernation: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[    0.038878] PM: hibernation: Registered nosave memory: [mem 0xfed45000-0xfed7ffff]
[    0.038880] PM: hibernation: Registered nosave memory: [mem 0xfed80000-0xfed8ffff]
[    0.038883] PM: hibernation: Registered nosave memory: [mem 0xfed90000-0xfeffffff]
[    0.038886] PM: hibernation: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.038888] PM: hibernation: Registered nosave memory: [mem 0x100000000-0x100000fff]
[    0.038894] [mem 0x9f000000-0xfebfffff] available for PCI devices
[    0.038899] Booting paravirtualized kernel on bare hardware
[    0.038905] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.050688] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.051444] percpu: Embedded 61 pages/cpu s212992 r8192 d28672 u524288
[    0.051488] pcpu-alloc: s212992 r8192 d28672 u524288 alloc=1*2097152
[    0.051498] pcpu-alloc: [0] 0 1 2 3
[    0.051634] Fallback order for Node 0: 0
[    0.051643] Built 1 zonelists, mobility grouping on.  Total pages: 1917587
[    0.051647] Policy zone: Normal
[    0.051651] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-6.1.0-25-amd64 root=UUID=3126d402-493e-49fe-94e8-b977da24a4a4 ro quiet
[    0.051787] Unknown kernel command line parameters "BOOT_IMAGE=/boot/vmlinuz-6.1.0-25-amd64", will be passed to user space.
[    0.054394] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.055723] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.055820] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[    0.055833] software IO TLB: area num 4.
[    0.135857] Memory: 2525612K/7792752K available (14342K kernel code, 2335K rwdata, 9072K rodata, 2796K init, 17396K bss, 493028K reserved, 0K cma-reserved)
[    0.136828] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.136936] ftrace: allocating 40246 entries in 158 pages
[    0.153906] ftrace: allocated 158 pages with 5 groups
[    0.155658] Dynamic Preempt: voluntary
[    0.155773] rcu: Preemptible hierarchical RCU implementation.
[    0.155775] rcu:     RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[    0.155779]  Trampoline variant of Tasks RCU enabled.
[    0.155780]  Rude variant of Tasks RCU enabled.
[    0.155782]  Tracing variant of Tasks RCU enabled.
[    0.155784] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.155786] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.172608] NR_IRQS: 524544, nr_irqs: 1000, preallocated irqs: 16
[    0.172899] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.173001] spurious 8259A interrupt: IRQ7.
[    0.173039] Console: colour dummy device 80x25
[    0.173091] printk: console [tty0] enabled
[    0.173168] ACPI: Core revision 20220331
[    0.173467] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[    0.173496] APIC: Switch to symmetric I/O mode setup
[    0.174054] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.193495] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x15950fbb5ea, max_idle_ns: 440795237167 ns
[    0.193513] Calibrating delay loop (skipped), value calculated using timer frequency.. 2994.54 BogoMIPS (lpj=5989080)
[    0.193564] LVT offset 1 assigned for vector 0xf9
[    0.193576] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
[    0.193579] Last level dTLB entries: 4KB 512, 2MB 256, 4MB 128, 1GB 0
[    0.193589] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.193595] Spectre V2 : Mitigation: Retpolines
[    0.193597] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.193600] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT
[    0.193602] Spectre V2 : Enabling Speculation Barrier for firmware calls
[    0.193604] RETBleed: Mitigation: untrained return thunk
[    0.193609] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.193613] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl
[    0.193625] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.193629] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.193633] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.193637] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.193641] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[    0.230388] Freeing SMP alternatives memory: 36K
[    0.230403] pid_max: default: 32768 minimum: 301
[    0.247298] LSM: Security Framework initializing
[    0.247369] landlock: Up and running.
[    0.247373] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.247475] AppArmor: AppArmor initialized
[    0.247482] TOMOYO Linux initialized
[    0.247497] LSM support for eBPF active
[    0.247685] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.247738] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.360829] smpboot: CPU0: AMD GX-415GA SOC with Radeon(tm) HD Graphics (family: 0x16, model: 0x0, stepping: 0x1)
[    0.361363] cblist_init_generic: Setting adjustable number of callback queues.
[    0.361367] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.361450] cblist_init_generic: Setting adjustable number of callback queues.
[    0.361454] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.361503] cblist_init_generic: Setting adjustable number of callback queues.
[    0.361503] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.361503] Performance Events: AMD PMU driver.
[    0.361503] ... version:                0
[    0.361503] ... bit width:              48
[    0.361503] ... generic registers:      4
[    0.361503] ... value mask:             0000ffffffffffff
[    0.361503] ... max period:             00007fffffffffff
[    0.361503] ... fixed-purpose events:   0
[    0.361503] ... event mask:             000000000000000f
[    0.361503] signal: max sigframe size: 1776
[    0.361503] rcu: Hierarchical SRCU implementation.
[    0.361503] rcu:     Max phase no-delay instances is 1000.
[    0.361503] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.361503] smp: Bringing up secondary CPUs ...
[    0.361503] x86: Booting SMP configuration:
[    0.361503] .... node  #0, CPUs:      #1 #2 #3
[    0.368280] smp: Brought up 1 node, 4 CPUs
[    0.368280] smpboot: Max logical packages: 1
[    0.368280] smpboot: Total of 4 processors activated (11978.16 BogoMIPS)
[    0.394040] node 0 deferred pages initialised in 24ms
[    0.398138] devtmpfs: initialized
[    0.398138] x86/mm: Memory block size: 128MB
[    0.400402] ACPI: PM: Registering ACPI NVS region [mem 0x9c928000-0x9ca1ffff] (1015808 bytes)
[    0.401582] ACPI: PM: Registering ACPI NVS region [mem 0x9e0b1000-0x9e0b8fff] (32768 bytes)
[    0.401727] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.401761] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.401871] pinctrl core: initialized pinctrl subsystem
[    0.404347] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.405086] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    0.405453] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.405853] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.405901] audit: initializing netlink subsys (disabled)
[    0.405973] audit: type=2000 audit(1727959571.232:1): state=initialized audit_enabled=0 res=1
[    0.405973] thermal_sys: Registered thermal governor 'fair_share'
[    0.405973] thermal_sys: Registered thermal governor 'bang_bang'
[    0.405973] thermal_sys: Registered thermal governor 'step_wise'
[    0.405973] thermal_sys: Registered thermal governor 'user_space'
[    0.405973] thermal_sys: Registered thermal governor 'power_allocator'
[    0.405978] cpuidle: using governor ladder
[    0.406000] cpuidle: using governor menu
[    0.406000] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.406000] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.406000] PCI: not using MMCONFIG
[    0.406000] PCI: Using configuration type 1 for base access
[    0.406000] PCI: Using configuration type 1 for extended access
[    0.410995] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.413971] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[    0.413975] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page
[    0.413980] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[    0.413983] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[    0.415279] ACPI: Added _OSI(Module Device)
[    0.415284] ACPI: Added _OSI(Processor Device)
[    0.415287] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.415290] ACPI: Added _OSI(Processor Aggregator Device)
[    0.433846] ACPI: 6 ACPI AML tables successfully acquired and loaded
[    0.458241] ACPI: USB4 _OSC: OS supports USB3+ DisplayPort+ PCIe+ XDomain+
[    0.458241] ACPI: USB4 _OSC: OS controls USB3+ DisplayPort+ PCIe+ XDomain+
[    0.459014] ACPI: Interpreter enabled
[    0.459064] ACPI: PM: (supports S0 S3 S5)
[    0.459069] ACPI: Using IOAPIC for interrupt routing
[    0.459186] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.459310] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.459361] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.459365] PCI: Using E820 reservations for host bridge windows
[    0.459365] ACPI: Enabled 6 GPEs in block 00 to 1F
[    0.476030] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.476050] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[    0.476445] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR]
[    0.477271] PCI host bridge to bus 0000:00
[    0.477278] pci_bus 0000:00: root bus resource [io  0x0000-0x03af window]
[    0.477286] pci_bus 0000:00: root bus resource [io  0x03e0-0x0cf7 window]
[    0.477292] pci_bus 0000:00: root bus resource [io  0x03b0-0x03df window]
[    0.477297] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.477303] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window]
[    0.477309] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
[    0.477315] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.477352] pci 0000:00:00.0: [1022:1536] type 00 class 0x060000
[    0.477598] pci 0000:00:01.0: [1002:9833] type 00 class 0x030000
[    0.477620] pci 0000:00:01.0: reg 0x10: [mem 0xc0000000-0xcfffffff 64bit pref]
[    0.477635] pci 0000:00:01.0: reg 0x18: [mem 0xd0000000-0xd07fffff 64bit pref]
[    0.477647] pci 0000:00:01.0: reg 0x20: [io  0xf000-0xf0ff]
[    0.477658] pci 0000:00:01.0: reg 0x24: [mem 0xfeb00000-0xfeb3ffff]
[    0.477669] pci 0000:00:01.0: reg 0x30: [mem 0xfeb40000-0xfeb5ffff pref]
[    0.477680] pci 0000:00:01.0: enabling Extended Tags
[    0.477701] pci 0000:00:01.0: BAR 0: assigned to efifb
[    0.477710] pci 0000:00:01.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.477752] pci 0000:00:01.0: supports D1 D2
[    0.477756] pci 0000:00:01.0: PME# supported from D1 D2 D3hot
[    0.477904] pci 0000:00:01.1: [1002:9840] type 00 class 0x040300
[    0.477926] pci 0000:00:01.1: reg 0x10: [mem 0xfeb64000-0xfeb67fff 64bit]
[    0.477965] pci 0000:00:01.1: enabling Extended Tags
[    0.478017] pci 0000:00:01.1: supports D1 D2
[    0.478140] pci 0000:00:02.0: [1022:1538] type 00 class 0x060000
[    0.478279] pci 0000:00:02.3: [1022:1439] type 01 class 0x060400
[    0.478328] pci 0000:00:02.3: enabling Extended Tags
[    0.478389] pci 0000:00:02.3: PME# supported from D0 D3hot D3cold
[    0.478631] pci 0000:00:10.0: [1022:7814] type 00 class 0x0c0330
[    0.478659] pci 0000:00:10.0: reg 0x10: [mem 0xfeb68000-0xfeb69fff 64bit]
[    0.478778] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
[    0.478998] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
[    0.479018] pci 0000:00:11.0: reg 0x10: [io  0xf140-0xf147]
[    0.479030] pci 0000:00:11.0: reg 0x14: [io  0xf130-0xf133]
[    0.479042] pci 0000:00:11.0: reg 0x18: [io  0xf120-0xf127]
[    0.479054] pci 0000:00:11.0: reg 0x1c: [io  0xf110-0xf113]
[    0.479066] pci 0000:00:11.0: reg 0x20: [io  0xf100-0xf10f]
[    0.479077] pci 0000:00:11.0: reg 0x24: [mem 0xfeb6e000-0xfeb6e3ff]
[    0.479137] pci 0000:00:11.0: PME# supported from D3hot
[    0.479319] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
[    0.479339] pci 0000:00:12.0: reg 0x10: [mem 0xfeb6d000-0xfeb6dfff]
[    0.479602] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
[    0.479623] pci 0000:00:12.2: reg 0x10: [mem 0xfeb6c000-0xfeb6c0ff]
[    0.479708] pci 0000:00:12.2: supports D1 D2
[    0.479712] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.479907] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
[    0.479927] pci 0000:00:13.0: reg 0x10: [mem 0xfeb6b000-0xfeb6bfff]
[    0.480163] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
[    0.480183] pci 0000:00:13.2: reg 0x10: [mem 0xfeb6a000-0xfeb6a0ff]
[    0.480267] pci 0000:00:13.2: supports D1 D2
[    0.480271] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.480454] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
[    0.480627] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
[    0.480651] pci 0000:00:14.2: reg 0x10: [mem 0xfeb60000-0xfeb63fff 64bit]
[    0.480724] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.480894] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
[    0.481166] pci 0000:00:18.0: [1022:1530] type 00 class 0x060000
[    0.481286] pci 0000:00:18.1: [1022:1531] type 00 class 0x060000
[    0.481418] pci 0000:00:18.2: [1022:1532] type 00 class 0x060000
[    0.481574] pci 0000:00:18.3: [1022:1533] type 00 class 0x060000
[    0.481745] pci 0000:00:18.4: [1022:1534] type 00 class 0x060000
[    0.481876] pci 0000:00:18.5: [1022:1535] type 00 class 0x060000
[    0.482120] pci 0000:01:00.0: [10ec:8168] type 00 class 0x020000
[    0.482146] pci 0000:01:00.0: reg 0x10: [io  0xe000-0xe0ff]
[    0.482177] pci 0000:01:00.0: reg 0x18: [mem 0xfea00000-0xfea00fff 64bit]
[    0.482198] pci 0000:01:00.0: reg 0x20: [mem 0xd0800000-0xd0803fff 64bit pref]
[    0.482319] pci 0000:01:00.0: supports D1 D2
[    0.482324] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.485508] pci 0000:00:02.3: PCI bridge to [bus 01]
[    0.485508] pci 0000:00:02.3:   bridge window [io  0xe000-0xefff]
[    0.485508] pci 0000:00:02.3:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.485508] pci 0000:00:02.3:   bridge window [mem 0xd0800000-0xd08fffff 64bit pref]
[    0.485508] ACPI: PCI: Interrupt link LNKA configured for IRQ 4
[    0.485508] ACPI: PCI: Interrupt link LNKB configured for IRQ 10
[    0.485508] ACPI: PCI: Interrupt link LNKC configured for IRQ 5
[    0.485508] ACPI: PCI: Interrupt link LNKD configured for IRQ 11
[    0.485508] ACPI: PCI: Interrupt link LNKE configured for IRQ 11
[    0.485508] ACPI: PCI: Interrupt link LNKF configured for IRQ 10
[    0.485508] ACPI: PCI: Interrupt link LNKG configured for IRQ 0
[    0.485508] ACPI: PCI: Interrupt link LNKH configured for IRQ 0
[    0.486174] iommu: Default domain type: Translated
[    0.486174] iommu: DMA domain TLB invalidation policy: lazy mode
[    0.486174] pps_core: LinuxPPS API ver. 1 registered
[    0.486174] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.486174] PTP clock support registered
[    0.486174] EDAC MC: Ver: 3.0.0
[    0.489602] Registered efivars operations
[    0.490042] NetLabel: Initializing
[    0.490045] NetLabel:  domain hash size = 128
[    0.490048] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.490108] NetLabel:  unlabeled traffic allowed by default
[    0.490113] PCI: Using ACPI for IRQ routing
[    0.495539] PCI: pci_cache_line_size set to 64 bytes
[    0.495603] e820: reserve RAM buffer [mem 0x90c21000-0x93ffffff]
[    0.495609] e820: reserve RAM buffer [mem 0x9c8ca000-0x9fffffff]
[    0.495615] e820: reserve RAM buffer [mem 0x9e0b1000-0x9fffffff]
[    0.495619] e820: reserve RAM buffer [mem 0x9e215000-0x9fffffff]
[    0.495623] e820: reserve RAM buffer [mem 0x9e8f0000-0x9fffffff]
[    0.495627] e820: reserve RAM buffer [mem 0x9f000000-0x9fffffff]
[    0.495630] e820: reserve RAM buffer [mem 0x23f000000-0x23fffffff]
[    0.497596] pci 0000:00:01.0: vgaarb: setting as boot VGA device
[    0.497596] pci 0000:00:01.0: vgaarb: bridge control possible
[    0.497596] pci 0000:00:01.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.497596] vgaarb: loaded
[    0.497628] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.497642] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[    0.497642] clocksource: Switched to clocksource tsc-early
[    0.498080] VFS: Disk quotas dquot_6.6.0
[    0.498125] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.498587] AppArmor: AppArmor Filesystem Enabled
[    0.498636] pnp: PnP ACPI init
[    0.498933] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[    0.499118] system 00:01: [mem 0xa0000000-0xbfffffff] has been reserved
[    0.500085] system 00:02: [io  0x0a00-0x0a1f] has been reserved
[    0.500094] system 00:02: [io  0x0a80-0x0a9f] has been reserved
[    0.500099] system 00:02: [io  0x0a50-0x0a5f] has been reserved
[    0.500452] system 00:05: [io  0x04d0-0x04d1] has been reserved
[    0.501926] system 00:08: [io  0x04d0-0x04d1] has been reserved
[    0.501935] system 00:08: [io  0x040b] has been reserved
[    0.501940] system 00:08: [io  0x04d6] has been reserved
[    0.501945] system 00:08: [io  0x0c00-0x0c01] has been reserved
[    0.501950] system 00:08: [io  0x0c14] has been reserved
[    0.501955] system 00:08: [io  0x0c50-0x0c51] has been reserved
[    0.501960] system 00:08: [io  0x0c52] has been reserved
[    0.501965] system 00:08: [io  0x0c6c] has been reserved
[    0.501969] system 00:08: [io  0x0c6f] has been reserved
[    0.501974] system 00:08: [io  0x0cd0-0x0cd1] has been reserved
[    0.501979] system 00:08: [io  0x0cd2-0x0cd3] has been reserved
[    0.501984] system 00:08: [io  0x0cd4-0x0cd5] has been reserved
[    0.501989] system 00:08: [io  0x0cd6-0x0cd7] has been reserved
[    0.501994] system 00:08: [io  0x0cd8-0x0cdf] has been reserved
[    0.501999] system 00:08: [io  0x0800-0x089f] has been reserved
[    0.502004] system 00:08: [io  0x0b20-0x0b3f] has been reserved
[    0.502009] system 00:08: [io  0x0900-0x090f] has been reserved
[    0.502013] system 00:08: [io  0x0910-0x091f] has been reserved
[    0.502019] system 00:08: [io  0xfe00-0xfefe] has been reserved
[    0.502040] system 00:08: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.502050] system 00:08: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.502057] system 00:08: [mem 0xfed80000-0xfed8ffff] has been reserved
[    0.502063] system 00:08: [mem 0xfed61000-0xfed70fff] has been reserved
[    0.502070] system 00:08: [mem 0xfec10000-0xfec10fff] has been reserved
[    0.502075] system 00:08: [mem 0xfed00000-0xfed00fff] could not be reserved
[    0.502083] system 00:08: [mem 0xff000000-0xffffffff] has been reserved
[    0.502600] pnp: PnP ACPI: found 9 devices
[    0.513268] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.513568] NET: Registered PF_INET protocol family
[    0.514083] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.519164] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.519301] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.519507] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.520478] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[    0.521181] TCP: Hash tables configured (established 65536 bind 65536)
[    0.521648] MPTCP token hash table entries: 8192 (order: 5, 196608 bytes, linear)
[    0.521799] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.521900] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.522092] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.522116] NET: Registered PF_XDP protocol family
[    0.522156] pci 0000:00:02.3: PCI bridge to [bus 01]
[    0.522168] pci 0000:00:02.3:   bridge window [io  0xe000-0xefff]
[    0.522177] pci 0000:00:02.3:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.522185] pci 0000:00:02.3:   bridge window [mem 0xd0800000-0xd08fffff 64bit pref]
[    0.522198] pci_bus 0000:00: resource 4 [io  0x0000-0x03af window]
[    0.522204] pci_bus 0000:00: resource 5 [io  0x03e0-0x0cf7 window]
[    0.522209] pci_bus 0000:00: resource 6 [io  0x03b0-0x03df window]
[    0.522214] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]
[    0.522219] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000dffff window]
[    0.522224] pci_bus 0000:00: resource 9 [mem 0xc0000000-0xffffffff window]
[    0.522229] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.522234] pci_bus 0000:01: resource 1 [mem 0xfea00000-0xfeafffff]
[    0.522238] pci_bus 0000:01: resource 2 [mem 0xd0800000-0xd08fffff 64bit pref]
[    0.522463] pci 0000:00:01.1: D0 power state depends on 0000:00:01.0
[    0.661333] pci 0000:00:12.0: quirk_usb_early_handoff+0x0/0x750 took 135158 usecs
[    0.681348] pci 0000:00:12.2: quirk_usb_early_handoff+0x0/0x750 took 19505 usecs
[    0.681373] pci 0000:00:12.2: PME# does not work under D3, disabling it
[    0.765360] pci 0000:00:13.0: quirk_usb_early_handoff+0x0/0x750 took 81997 usecs
[    0.785352] pci 0000:00:13.2: quirk_usb_early_handoff+0x0/0x750 took 19483 usecs
[    0.785377] pci 0000:00:13.2: PME# does not work under D3, disabling it
[    0.785438] PCI: CLS 64 bytes, default 64
[    0.785476] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.785479] software IO TLB: mapped [mem 0x000000008b274000-0x000000008f274000] (64MB)
[    0.785552] LVT offset 0 assigned for vector 0x400
[    0.785685] Trying to unpack rootfs image as initramfs...
[    0.785739] perf: AMD IBS detected (0x000000ff)
[    0.785751] amd_uncore: 4  amd_nb counters detected
[    0.785760] amd_uncore: 4  amd_l2 counters detected
[    0.787238] Initialise system trusted keyrings
[    0.787311] Key type blacklist registered
[    0.787605] workingset: timestamp_bits=36 max_order=21 bucket_order=0
[    0.792181] zbud: loaded
[    0.792953] integrity: Platform Keyring initialized
[    0.792987] integrity: Machine keyring initialized
[    0.792993] Key type asymmetric registered
[    0.792997] Asymmetric key parser 'x509' registered
[    1.644651] tsc: Refined TSC clocksource calibration: 1497.191 MHz
[    1.644678] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x1594c522ce2, max_idle_ns: 440795237962 ns
[    1.644723] clocksource: Switched to clocksource tsc
[    1.792795] Freeing initrd memory: 31276K
[    1.808702] alg: self-tests for CTR-KDF (hmac(sha256)) passed
[    1.808791] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.808889] io scheduler mq-deadline registered
[    1.812097] pcieport 0000:00:02.3: PME: Signaling with IRQ 25
[    1.812344] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    1.812452] ACPI: \_PR_.P000: Found 2 idle states
[    1.812760] ACPI: \_PR_.P001: Found 2 idle states
[    1.812979] ACPI: \_PR_.P002: Found 2 idle states
[    1.813185] ACPI: \_PR_.P003: Found 2 idle states
[    1.813885] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.815114] Linux agpgart interface v0.103
[    1.815645] AMD-Vi: AMD IOMMUv2 functionality not available on this system - This is not a bug.
[    1.816553] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    1.819473] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.819487] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.819832] mousedev: PS/2 mouse device common for all mice
[    1.819921] rtc_cmos 00:04: RTC can wake from S4
[    1.820309] rtc_cmos 00:04: registered as rtc0
[    1.820342] rtc_cmos 00:04: setting system clock to 2024-10-03T12:46:13 UTC (1727959573)
[    1.820402] rtc_cmos 00:04: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.820559] ledtrig-cpu: registered to indicate activity on CPUs
[    1.821134] efifb: probing for efifb
[    1.821158] efifb: framebuffer at 0xc0000000, using 1984k, total 1984k
[    1.821163] efifb: mode is 800x600x32, linelength=3328, pages=1
[    1.821167] efifb: scrolling: redraw
[    1.821169] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.821417] Console: switching to colour frame buffer device 100x37
[    1.822817] fb0: EFI VGA frame buffer device
[    1.853133] NET: Registered PF_INET6 protocol family
[    1.867878] Segment Routing with IPv6
[    1.867938] In-situ OAM (IOAM) with IPv6
[    1.868029] mip6: Mobile IPv6
[    1.868042] NET: Registered PF_PACKET protocol family
[    1.868140] mpls_gso: MPLS GSO support
[    1.868147] x86/pm: family 0x16 cpu detected, MSR saving is needed during suspending.
[    1.868747] microcode: CPU0: patch_level=0x07000110
[    1.868780] microcode: CPU1: patch_level=0x07000110
[    1.868791] microcode: CPU2: patch_level=0x07000110
[    1.868806] microcode: CPU3: patch_level=0x07000110
[    1.868815] microcode: Microcode Update Driver: v2.2.
[    1.868828] IPI shorthand broadcast: enabled
[    1.868889] sched_clock: Marking stable (1868006837, 575605)->(1875349647, -6767205)
[    1.869335] registered taskstats version 1
[    1.869360] Loading compiled-in X.509 certificates
[    1.933719] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[    1.933783] Loaded X.509 cert 'Debian Secure Boot Signer 2022 - linux: 14011249c2675ea8e5148542202005810584b25f'
[    1.934769] zswap: loaded using pool lzo/zbud
[    1.935291] Key type .fscrypt registered
[    1.935295] Key type fscrypt-provisioning registered
[    1.948963] Key type encrypted registered
[    1.948978] AppArmor: AppArmor sha1 policy hashing enabled
[    1.949271] integrity: Loading X.509 certificate: UEFI:db
[    1.949358] integrity: Loaded X.509 cert 'Hewlett-Packard UEFI Secure Boot DB Key: e7203ac28b848d3c03432f6a485dd1f4c7b8e529'
[    1.949363] integrity: Loading X.509 certificate: UEFI:db
[    1.949438] integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53'
[    1.949442] integrity: Loading X.509 certificate: UEFI:db
[    1.949508] integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4'
[    1.949677] ima: No TPM chip found, activating TPM-bypass!
[    1.949682] ima: Allocated hash algorithm: sha256
[    1.949717] ima: No architecture policies found
[    1.949773] evm: Initialising EVM extended attributes:
[    1.949776] evm: security.selinux
[    1.949779] evm: security.SMACK64 (disabled)
[    1.949781] evm: security.SMACK64EXEC (disabled)
[    1.949783] evm: security.SMACK64TRANSMUTE (disabled)
[    1.949785] evm: security.SMACK64MMAP (disabled)
[    1.949787] evm: security.apparmor
[    1.949789] evm: security.ima
[    1.949791] evm: security.capability
[    1.949793] evm: HMAC attrs: 0x1
[    2.308812] clk: Disabling unused clocks
[    2.312554] Freeing unused decrypted memory: 2036K
[    2.314133] Freeing unused kernel image (initmem) memory: 2796K
[    2.314151] Write protecting the kernel read-only data: 26624k
[    2.315783] Freeing unused kernel image (text/rodata gap) memory: 2040K
[    2.316459] Freeing unused kernel image (rodata/data gap) memory: 1168K
[    2.418438] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    2.418456] Run /init as init process
[    2.418460]   with arguments:
[    2.418463]     /init
[    2.418466]   with environment:
[    2.418469]     HOME=/
[    2.418471]     TERM=linux
[    2.418474]     BOOT_IMAGE=/boot/vmlinuz-6.1.0-25-amd64
[    2.732306] wmi_bus wmi_bus-PNP0C14:00: [Firmware Info]: 8F1F6436-9F42-42C8-BADC-0E9424F20C9A has zero instances
[    2.732322] wmi_bus wmi_bus-PNP0C14:00: [Firmware Info]: 8F1F6435-9F42-42C8-BADC-0E9424F20C9A has zero instances
[    2.732327] wmi_bus wmi_bus-PNP0C14:00: [Firmware Info]: 7391A661-223A-47DB-A77A-7BE84C60822D has zero instances
[    2.732332] wmi_bus wmi_bus-PNP0C14:00: [Firmware Info]: DF4E63B6-3BBC-4858-9737-C74F82F821F3 has zero instances
[    2.733916] acpi PNP0C14:01: duplicate WMI GUID 5FB7F034-2C63-45E9-BE91-3D44E2C707E4 (first instance was on PNP0C14:00)
[    2.775275] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[    2.775293] piix4_smbus 0000:00:14.0: Using register 0x02 for SMBus port selection
[    2.775461] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[    2.795574] ACPI: bus type USB registered
[    2.795671] usbcore: registered new interface driver usbfs
[    2.795701] usbcore: registered new interface driver hub
[    2.795742] usbcore: registered new device driver usb
[    2.828565] r8169 0000:01:00.0 eth0: RTL8168g/8111g, 7c:d3:0a:20:c0:27, XID 4c0, IRQ 27
[    2.828616] r8169 0000:01:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
[    2.840870] SCSI subsystem initialized
[    2.844087] xhci_hcd 0000:00:10.0: xHCI Host Controller
[    2.844113] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[    2.927048] libata version 3.00 loaded.
[    2.941042] ahci 0000:00:11.0: version 3.0
[    2.941441] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[    2.941453] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part deso sadm sds
[    2.942350] scsi host0: ahci
[    2.942850] scsi host1: ahci
[    2.943000] ata1: SATA max UDMA/133 abar m1024@0xfeb6e000 port 0xfeb6e100 irq 28
[    2.943007] ata2: SATA max UDMA/133 abar m1024@0xfeb6e000 port 0xfeb6e180 irq 28
[    2.949218] xhci_hcd 0000:00:10.0: hcc params 0x014040c3 hci version 0x100 quirks 0x0000000000000410
[    2.949736] ehci-pci 0000:00:12.2: EHCI Host Controller
[    2.949755] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2
[    2.949769] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    2.949781] ehci-pci 0000:00:12.2: debug port 1
[    2.949808] xhci_hcd 0000:00:10.0: xHCI Host Controller
[    2.949818] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 3
[    2.949828] xhci_hcd 0000:00:10.0: Host supports USB 3.0 SuperSpeed
[    2.949866] ehci-pci 0000:00:12.2: irq 17, io mem 0xfeb6c000
[    2.952724] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    2.952732] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.952737] usb usb1: Product: xHCI Host Controller
[    2.952741] usb usb1: Manufacturer: Linux 6.1.0-25-amd64 xhci-hcd
[    2.952745] usb usb1: SerialNumber: 0000:00:10.0
[    2.953105] hub 1-0:1.0: USB hub found
[    2.953130] hub 1-0:1.0: 2 ports detected
[    2.953430] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.953504] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    2.953511] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.953515] usb usb3: Product: xHCI Host Controller
[    2.953519] usb usb3: Manufacturer: Linux 6.1.0-25-amd64 xhci-hcd
[    2.953523] usb usb3: SerialNumber: 0000:00:10.0
[    2.953795] hub 3-0:1.0: USB hub found
[    2.953818] hub 3-0:1.0: 2 ports detected
[    2.961020] r8169 0000:01:00.0 enp1s0: renamed from eth0
[    2.964755] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    2.965046] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    2.965054] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.965060] usb usb2: Product: EHCI Host Controller
[    2.965064] usb usb2: Manufacturer: Linux 6.1.0-25-amd64 ehci_hcd
[    2.965067] usb usb2: SerialNumber: 0000:00:12.2
[    2.965523] hub 2-0:1.0: USB hub found
[    2.965555] hub 2-0:1.0: 4 ports detected
[    2.966502] ehci-pci 0000:00:13.2: EHCI Host Controller
[    2.966518] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 4
[    2.966529] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    2.966540] ehci-pci 0000:00:13.2: debug port 1
[    2.966606] ehci-pci 0000:00:13.2: irq 17, io mem 0xfeb6a000
[    2.980754] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    2.981071] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    2.981080] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.981085] usb usb4: Product: EHCI Host Controller
[    2.981089] usb usb4: Manufacturer: Linux 6.1.0-25-amd64 ehci_hcd
[    2.981093] usb usb4: SerialNumber: 0000:00:13.2
[    2.981545] hub 4-0:1.0: USB hub found
[    2.981580] hub 4-0:1.0: 4 ports detected
[    3.047366] ata1: SATA link down (SStatus 0 SControl 300)
[    3.212763] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    3.213599] ata2.00: ATA-11: SanDisk X600 M.2 2280 SATA 128GB, X6113012, max UDMA/133
[    3.214176] ata2.00: 250069680 sectors, multi 1: LBA48 NCQ (depth 32), AA
[    3.215170] ata2.00: Features: Dev-Sleep
[    3.217590] ata2.00: configured for UDMA/133
[    3.218051] scsi 1:0:0:0: Direct-Access     ATA      SanDisk X600 M.2 3012 PQ: 0 ANSI: 5
[    3.222952] ohci-pci 0000:00:12.0: OHCI PCI host controller
[    3.222977] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 5
[    3.223068] ohci-pci 0000:00:12.0: irq 18, io mem 0xfeb6d000
[    3.262418] sd 1:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[    3.262470] sd 1:0:0:0: [sda] Write Protect is off
[    3.262480] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.262567] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.262676] sd 1:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[    3.265257]  sda: sda1 sda2 sda3
[    3.265658] sd 1:0:0:0: [sda] Attached SCSI disk
[    3.288812] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    3.288853] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.288860] usb usb5: Product: OHCI PCI host controller
[    3.288864] usb usb5: Manufacturer: Linux 6.1.0-25-amd64 ohci_hcd
[    3.288866] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[    3.288868] usb usb5: SerialNumber: 0000:00:12.0
[    3.289395] hub 5-0:1.0: USB hub found
[    3.289421] hub 5-0:1.0: 4 ports detected
[    3.290307] ohci-pci 0000:00:13.0: OHCI PCI host controller
[    3.290324] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 6
[    3.290383] ohci-pci 0000:00:13.0: irq 18, io mem 0xfeb6b000
[    3.312689] usb 3-1: New USB device found, idVendor=152d, idProduct=0578, bcdDevice= 1.00
[    3.312705] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.312710] usb 3-1: Product: USB3.0 External HDD
[    3.312714] usb 3-1: Manufacturer: JMicron
[    3.312718] usb 3-1: SerialNumber: 0000AB1236CE
[    3.335393] usbcore: registered new interface driver usb-storage
[    3.345695] scsi host2: uas
[    3.346012] usbcore: registered new interface driver uas
[    3.346563] scsi 2:0:0:0: Direct-Access     WDC WD20 EFZX-68AWUN0     8101 PQ: 0 ANSI: 6
[    3.352749] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    3.352757] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.352763] usb usb6: Product: OHCI PCI host controller
[    3.352767] usb usb6: Manufacturer: Linux 6.1.0-25-amd64 ohci_hcd
[    3.352771] usb usb6: SerialNumber: 0000:00:13.0
[    3.353126] hub 6-0:1.0: USB hub found
[    3.353150] hub 6-0:1.0: 4 ports detected
[    3.364160] sd 2:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    3.364174] sd 2:0:0:0: [sdb] 4096-byte physical blocks
[    3.364549] sd 2:0:0:0: [sdb] Write Protect is off
[    3.364563] sd 2:0:0:0: [sdb] Mode Sense: 53 00 00 08
[    3.364986] sd 2:0:0:0: [sdb] Disabling FUA
[    3.364993] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.365327] sd 2:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[    3.365335] sd 2:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of preferred minimum block size (4096 bytes)
[    3.367386]  sdb: sdb1
[    3.367601] sd 2:0:0:0: [sdb] Attached SCSI disk
[    3.960788] usb 5-1: new full-speed USB device number 2 using ohci-pci
[    3.960866] usb 6-1: new full-speed USB device number 2 using ohci-pci
[    4.804772] usb 5-4: new full-speed USB device number 3 using ohci-pci
[    5.005812] usb 5-4: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=12.03
[    5.005827] usb 5-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.005832] usb 5-4: Product: USB Receiver
[    5.005836] usb 5-4: Manufacturer: Logitech
[    5.030024] hid: raw HID events driver (C) Jiri Kosina
[    5.051583] usbcore: registered new interface driver usbhid
[    5.051594] usbhid: USB HID core driver
[    5.056916] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.0/0003:046D:C52B.0001/input/input3
[    5.181022] hid-generic 0003:046D:C52B.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:12.0-4/input0
[    5.181867] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.1/0003:046D:C52B.0002/input/input4
[    5.182165] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.1/0003:046D:C52B.0002/input/input5
[    5.240935] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.1/0003:046D:C52B.0002/input/input6
[    5.241296] hid-generic 0003:046D:C52B.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:12.0-4/input1
[    5.241989] hid-generic 0003:046D:C52B.0003: hiddev1,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:12.0-4/input2
[    5.414658] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:12.0-4/input2
[    5.536864] input: Logitech Wireless Device PID:400a Mouse as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.2/0003:046D:C52B.0003/0003:046D:400A.0004/input/input8
[    5.537134] hid-generic 0003:046D:400A.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Wireless Device PID:400a] on usb-0000:00:12.0-4/input2:1
[    5.543356] input: Logitech Wireless Device PID:400d Keyboard as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.2/0003:046D:C52B.0003/0003:046D:400D.0005/input/input12
[    5.636981] hid-generic 0003:046D:400D.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Wireless Device PID:400d] on usb-0000:00:12.0-4/input2:2
[    5.660006] input: Logitech M325 as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.2/0003:046D:C52B.0003/0003:046D:400A.0004/input/input16
[    5.660294] logitech-hidpp-device 0003:046D:400A.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech M325] on usb-0000:00:12.0-4/input2:1
[    5.780251] input: Logitech K230 as /devices/pci0000:00/0000:00:12.0/usb5/5-4/5-4:1.2/0003:046D:C52B.0003/0003:046D:400D.0005/input/input17
[    5.845019] logitech-hidpp-device 0003:046D:400D.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech K230] on usb-0000:00:12.0-4/input2:2
Top
marqozzz
Posts: 5
Joined: 2024-10-02 21:15

Re: External hard disk disconnects under load with a HP t620 running Debian 12

#6 Post by marqozzz »

log - part 2

Code: Select all

[    6.044586] raid6: sse2x4   gen()  3917 MB/s
[    6.112582] raid6: sse2x2   gen()  3844 MB/s
[    6.180587] raid6: sse2x1   gen()  3112 MB/s
[    6.180590] raid6: using algorithm sse2x4 gen() 3917 MB/s
[    6.248587] raid6: .... xor() 1887 MB/s, rmw enabled
[    6.248592] raid6: using ssse3x2 recovery algorithm
[    6.251028] xor: automatically using best checksumming function   avx
[    6.252759] async_tx: api initialized (async)
[    6.380861] PM: Image not found (code -22)
[    6.662962] EXT4-fs (sda2): mounted filesystem with ordered data mode. Quota mode: none.
[    6.798556] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[    6.898056] systemd[1]: Inserted module 'autofs4'
[    6.956682] systemd[1]: systemd 252.30-1~deb12u2 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    6.956704] systemd[1]: Detected architecture x86-64.
[    6.958089] systemd[1]: Hostname set to <debian>.
[    7.258907] systemd[1]: Configuration file /etc/systemd/system/hfs.service is marked executable. Please remove executable permission bits. Proceeding anyway.
[    7.258927] systemd[1]: Configuration file /etc/systemd/system/hfs.service is marked world-writable. Please remove world writability permission bits. Proceeding anyway.
[    7.381515] systemd[1]: Queued start job for default target graphical.target.
[    7.404046] systemd[1]: Created slice system-getty.slice - Slice /system/getty.
[    7.405310] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe.
[    7.406423] systemd[1]: Created slice system-systemd\x2dcryptsetup.slice - Cryptsetup Units Slice.
[    7.407545] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck.
[    7.408351] systemd[1]: Created slice user.slice - User and Session Slice.
[    7.408632] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch.
[    7.408832] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch.
[    7.409450] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point.
[    7.409529] systemd[1]: Expecting device dev-disk-by\x2duuid-1a7200d7\x2dbab3\x2d45fa\x2db8be\x2d871bc3e83f7d.device - /dev/disk/by-uuid/1a7200d7-bab3-45fa-b8be-871bc3e83f7d...
[    7.409574] systemd[1]: Expecting device dev-disk-by\x2duuid-EF67\x2d7FC5.device - /dev/disk/by-uuid/EF67-7FC5...
[    7.409614] systemd[1]: Expecting device dev-disk-by\x2duuid-dbe75eaf\x2dbafd\x2d49b6\x2db15f\x2dd83844dc6624.device - /dev/disk/by-uuid/dbe75eaf-bafd-49b6-b15f-d83844dc6624...
[    7.409656] systemd[1]: Expecting device dev-disk-by\x2duuid-f08bb70d\x2d9cfd\x2d44bd\x2d9d8d\x2d6e401ce9d1f4.device - /dev/disk/by-uuid/f08bb70d-9cfd-44bd-9d8d-6e401ce9d1f4...
[    7.409777] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes.
[    7.409904] systemd[1]: Reached target paths.target - Path Units.
[    7.410022] systemd[1]: Reached target slices.target - Slice Units.
[    7.410166] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes.
[    7.420658] systemd[1]: Listening on rpcbind.socket - RPCbind Server Activation Socket.
[    7.421244] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket.
[    7.421502] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe.
[    7.422281] systemd[1]: Listening on systemd-journald-audit.socket - Journal Audit Socket.
[    7.422766] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[    7.423231] systemd[1]: Listening on systemd-journald.socket - Journal Socket.
[    7.424010] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket.
[    7.424384] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[    7.427462] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System...
[    7.430511] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System...
[    7.434073] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System...
[    7.437401] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System...
[    7.437808] systemd[1]: auth-rpcgss-module.service - Kernel Module supporting RPCSEC_GSS was skipped because of an unmet condition check (ConditionPathExists=/etc/krb5.keytab).
[    7.442388] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout...
[    7.445963] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes...
[    7.449881] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs...
[    7.453762] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod...
[    7.457730] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm...
[    7.461654] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore...
[    7.465690] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse...
[    7.470285] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop...
[    7.470936] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root).
[    7.476490] systemd[1]: Starting systemd-journald.service - Journal Service...
[    7.485031] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules...
[    7.494768] pstore: Using crash dump compression: deflate
[    7.496139] loop: module loaded
[    7.497845] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems...
[    7.505120] pstore: Registered efi as persistent store backend
[    7.509976] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices...
[    7.516370] systemd[1]: Mounted dev-hugepages.mount - Huge Pages File System.
[    7.517292] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System.
[    7.517602] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System.
[    7.517899] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System.
[    7.518779] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes.
[    7.518932] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log.
[    7.519035] device-mapper: uevent: version 1.0.3
[    7.519928] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[    7.520511] systemd[1]: Finished modprobe@configfs.service - Load Kernel Module configfs.
[    7.521803] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[    7.522333] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore.
[    7.523643] systemd[1]: modprobe@loop.service: Deactivated successfully.
[    7.524200] systemd[1]: Finished modprobe@loop.service - Load Kernel Module loop.
[    7.531396] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    7.535820] systemd[1]: modprobe@dm_mod.service: Deactivated successfully.
[    7.536354] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod.
[    7.540090] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System...
[    7.542162] systemd[1]: systemd-repart.service - Repartition Root Disk was skipped because no trigger condition checks were met.
[    7.544323] systemd[1]: Finished systemd-modules-load.service - Load Kernel Modules.
[    7.548784] fuse: init (API version 7.37)
[    7.563684] systemd[1]: Starting systemd-sysctl.service - Apply Kernel Variables...
[    7.571791] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System.
[    7.572108] EXT4-fs (sda2): re-mounted. Quota mode: none.
[    7.575887] systemd[1]: Finished systemd-remount-fs.service - Remount Root and Kernel File Systems.
[    7.576325] systemd[1]: systemd-firstboot.service - First Boot Wizard was skipped because of an unmet condition check (ConditionFirstBoot=yes).
[    7.576475] systemd[1]: systemd-pstore.service - Platform Persistent Storage Archival was skipped because of an unmet condition check (ConditionDirectoryNotEmpty=/sys/fs/pstore).
[    7.579823] systemd[1]: Starting systemd-random-seed.service - Load/Save Random Seed...
[    7.583693] systemd[1]: Starting systemd-sysusers.service - Create System Users...
[    7.595226] ACPI: bus type drm_connector registered
[    7.595709] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[    7.596466] systemd[1]: Finished modprobe@fuse.service - Load Kernel Module fuse.
[    7.601538] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System...
[    7.607208] systemd[1]: modprobe@drm.service: Deactivated successfully.
[    7.607805] systemd[1]: Finished modprobe@drm.service - Load Kernel Module drm.
[    7.622344] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System.
[    7.631535] systemd[1]: Finished systemd-sysctl.service - Apply Kernel Variables.
[    7.647926] systemd[1]: Finished systemd-sysusers.service - Create System Users.
[    7.673187] systemd[1]: Starting systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev...
[    7.737371] systemd[1]: Finished systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev.
[    7.757227] systemd[1]: Starting systemd-udevd.service - Rule-based Manager for Device Events and Files...
[    7.803068] systemd[1]: Finished keyboard-setup.service - Set the console keyboard layout.
[    7.803431] systemd[1]: Reached target local-fs-pre.target - Preparation for Local File Systems.
[    7.865760] systemd[1]: Started systemd-journald.service - Journal Service.
[    7.917156] systemd-journald[279]: Received client request to flush runtime journal.
[    8.238654] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    8.238794] sd 2:0:0:0: Attached scsi generic sg1 type 0
[    8.359111] acpi_cpufreq: overriding BIOS provided _PSD data
[    8.401782] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input18
[    8.416772] ACPI: button: Power Button [PWRB]
[    8.427412] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input19
[    8.462452] ACPI: button: Power Button [PWRF]
[    8.584616] random: crng init done
[    8.593947] input: PC Speaker as /devices/platform/pcspkr/input/input20
[    8.632118] usbcore: registered new interface driver usbserial_generic
[    8.632166] usbserial: USB Serial support registered for generic
[    8.641425] cryptd: max_cpu_qlen set to 1000
[    8.682765] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver
[    8.683259] sp5100-tco sp5100-tco: Using 0xfed80b00 for watchdog MMIO address
[    8.689744] sp5100-tco sp5100-tco: initialized. heartbeat=60 sec (nowayout=0)
[    8.706573] input: HP WMI hotkeys as /devices/virtual/input/input21
[    8.719129] AVX version of gcm_enc/dec engaged.
[    8.719198] AES CTR mode by8 optimization enabled
[    8.877736] Adding 1000444k swap on /dev/sda3.  Priority:-2 extents:1 across:1000444k SSFS
[    8.898378] snd_hda_intel 0000:00:01.1: Force to non-snoop mode
[    9.199962] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input22
[    9.211297] [drm] radeon kernel modesetting enabled.
[    9.211384] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.1/sound/card0/input23
[    9.227886] Console: switching to colour dummy device 80x25
[    9.228105] radeon 0000:00:01.0: vgaarb: deactivate vga console
[    9.228870] [drm] initializing kernel modesetting (KABINI 0x1002:0x9833 0x103C:0x21B4 0x00).
[    9.228924] [drm] doorbell mmio base: 0xD0000000
[    9.228928] [drm] doorbell mmio size: 8388608
[    9.229023] ATOM BIOS: HP
[    9.229103] radeon 0000:00:01.0: VRAM: 512M 0x0000000000000000 - 0x000000001FFFFFFF (512M used)
[    9.229113] radeon 0000:00:01.0: GTT: 2048M 0x0000000020000000 - 0x000000009FFFFFFF
[    9.229124] [drm] Detected VRAM RAM=512M, BAR=256M
[    9.229128] [drm] RAM width 128bits DDR
[    9.229206] [drm] radeon: 512M of VRAM memory ready
[    9.229211] [drm] radeon: 2048M of GTT memory ready.
[    9.229236] [drm] Loading kabini Microcode
[    9.241726] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/kabini_pfp.bin
[    9.242112] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/kabini_me.bin
[    9.242420] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/kabini_ce.bin
[    9.242775] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/kabini_mec.bin
[    9.244018] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/kabini_rlc.bin
[    9.244458] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/kabini_sdma.bin
[    9.244476] [drm] Internal thermal controller without fan control
[    9.245892] [drm] radeon: dpm initialized
[    9.248816] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/bonaire_uvd.bin
[    9.248848] [drm] Found UVD firmware Version: 1.64 Family ID: 9
[    9.249716] radeon 0000:00:01.0: firmware: direct-loading firmware radeon/BONAIRE_vce.bin
[    9.251913] [drm] Found VCE firmware/feedback version 40.2.2 / 15!
[    9.251959] [drm] GART: num cpu pages 524288, num gpu pages 524288
[    9.283816] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC221: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[    9.283843] snd_hda_codec_realtek hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    9.283850] snd_hda_codec_realtek hdaudioC1D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[    9.283857] snd_hda_codec_realtek hdaudioC1D0:    mono: mono_out=0x0
[    9.283861] snd_hda_codec_realtek hdaudioC1D0:    inputs:
[    9.283866] snd_hda_codec_realtek hdaudioC1D0:      Mic=0x1a
[    9.283871] snd_hda_codec_realtek hdaudioC1D0:      Line=0x1b
[    9.288330] [drm] PCIE GART of 2048M enabled (table at 0x000000000030E000).
[    9.288647] radeon 0000:00:01.0: WB enabled
[    9.288698] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000020000c00
[    9.288708] radeon 0000:00:01.0: fence driver on ring 1 use gpu addr 0x0000000020000c04
[    9.288714] radeon 0000:00:01.0: fence driver on ring 2 use gpu addr 0x0000000020000c08
[    9.288720] radeon 0000:00:01.0: fence driver on ring 3 use gpu addr 0x0000000020000c0c
[    9.288725] radeon 0000:00:01.0: fence driver on ring 4 use gpu addr 0x0000000020000c10
[    9.289878] radeon 0000:00:01.0: fence driver on ring 5 use gpu addr 0x0000000000078d30
[    9.290337] radeon 0000:00:01.0: fence driver on ring 6 use gpu addr 0x0000000020000c18
[    9.290347] radeon 0000:00:01.0: fence driver on ring 7 use gpu addr 0x0000000020000c1c
[    9.290829] radeon 0000:00:01.0: radeon: using MSI.
[    9.290913] [drm] radeon: irq initialized.
[    9.296922] [drm] ring test on 0 succeeded in 2 usecs
[    9.297037] [drm] ring test on 1 succeeded in 3 usecs
[    9.297067] [drm] ring test on 2 succeeded in 3 usecs
[    9.297302] [drm] ring test on 3 succeeded in 4 usecs
[    9.297313] [drm] ring test on 4 succeeded in 3 usecs
[    9.349228] [drm] ring test on 5 succeeded in 1 usecs
[    9.368540] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/sound/card1/input24
[    9.368779] input: HD-Audio Generic Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input25
[    9.368928] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input26
[    9.369083] input: HD-Audio Generic Line Out as /devices/pci0000:00/0000:00:14.2/sound/card1/input27
[    9.369235] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input28
[    9.379631] [drm] UVD initialized successfully.
[    9.588637] [drm] ring test on 6 succeeded in 16 usecs
[    9.588665] [drm] ring test on 7 succeeded in 3 usecs
[    9.588668] [drm] VCE initialized successfully.
[    9.591719] [drm] ib test on ring 0 succeeded in 0 usecs
[    9.591898] [drm] ib test on ring 1 succeeded in 0 usecs
[    9.592060] [drm] ib test on ring 2 succeeded in 0 usecs
[    9.592228] [drm] ib test on ring 3 succeeded in 0 usecs
[    9.592392] [drm] ib test on ring 4 succeeded in 0 usecs
[   10.082737] kvm: support for 'kvm_amd' disabled by bios
[   10.124791] [drm] ib test on ring 5 succeeded
[   10.159137] MCE: In-kernel MCE decoding enabled.
[   10.161692] [drm] ib test on ring 6 succeeded
[   10.162394] [drm] ib test on ring 7 succeeded
[   10.168397] [drm] Radeon Display Connectors
[   10.168408] [drm] Connector 0:
[   10.168411] [drm]   DP-1
[   10.168413] [drm]   HPD1
[   10.168415] [drm]   DDC: 0x6530 0x6530 0x6534 0x6534 0x6538 0x6538 0x653c 0x653c
[   10.168421] [drm]   Encoders:
[   10.168423] [drm]     DFP1: INTERNAL_UNIPHY
[   10.168426] [drm] Connector 1:
[   10.168428] [drm]   DP-2
[   10.168430] [drm]   HPD2
[   10.168432] [drm]   DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c
[   10.168437] [drm]   Encoders:
[   10.168438] [drm]     DFP2: INTERNAL_UNIPHY
[   10.168440] [drm] Connector 2:
[   10.168442] [drm]   VGA-1
[   10.168444] [drm]   DDC: 0x65c0 0x65c0 0x65c4 0x65c4 0x65c8 0x65c8 0x65cc 0x65cc
[   10.168449] [drm]   Encoders:
[   10.168451] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[   10.328775] snd_hda_codec_hdmi hdaudioC0D0: HDMI ATI/AMD: no speaker allocation for ELD
[   10.347925] [drm] fb mappable at 0xC0731000
[   10.347940] [drm] vram apper at 0xC0000000
[   10.347942] [drm] size 8294400
[   10.347945] [drm] fb depth is 24
[   10.347947] [drm]    pitch is 7680
[   10.348225] fbcon: radeondrmfb (fb0) is primary device
[   10.394350] Console: switching to colour frame buffer device 240x67
[   10.401240] radeon 0000:00:01.0: [drm] fb0: radeondrmfb frame buffer device
[   10.436237] [drm] Initialized radeon 2.50.0 20080528 for 0000:00:01.0 on minor 0
[   15.719111] [drm] amdgpu kernel modesetting enabled.
[   15.719374] amdgpu: Ignoring ACPI CRAT on non-APU system
[   15.719385] amdgpu: Virtual CRAT table created for CPU
[   15.719419] amdgpu: Topology: Add CPU node
[   16.007094] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Quota mode: none.
[   16.109613] audit: type=1400 audit(1727959587.787:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=636 comm="apparmor_parser"
[   16.110852] audit: type=1400 audit(1727959587.787:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=637 comm="apparmor_parser"
[   16.110866] audit: type=1400 audit(1727959587.787:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=637 comm="apparmor_parser"
[   16.118747] audit: type=1400 audit(1727959587.795:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=639 comm="apparmor_parser"
[   16.118768] audit: type=1400 audit(1727959587.795:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=639 comm="apparmor_parser"
[   16.118779] audit: type=1400 audit(1727959587.795:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=639 comm="apparmor_parser"
[   16.130001] audit: type=1400 audit(1727959587.807:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=638 comm="apparmor_parser"
[   16.130021] audit: type=1400 audit(1727959587.807:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=638 comm="apparmor_parser"
[   16.130031] audit: type=1400 audit(1727959587.807:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=638 comm="apparmor_parser"
[   16.130041] audit: type=1400 audit(1727959587.807:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=638 comm="apparmor_parser"
[   16.282299] r8169 0000:01:00.0: firmware: direct-loading firmware rtl_nic/rtl8168g-2.fw
[   16.308656] Generic FE-GE Realtek PHY r8169-0-100:00: attached PHY driver (mii_bus:phy_addr=r8169-0-100:00, irq=MAC)
[   16.345610] RPC: Registered named UNIX socket transport module.
[   16.345622] RPC: Registered udp transport module.
[   16.345625] RPC: Registered tcp transport module.
[   16.345627] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   16.517769] r8169 0000:01:00.0 enp1s0: Link is Down
[   16.907242] NET: Registered PF_QIPCRTR protocol family
[   19.421575] r8169 0000:01:00.0 enp1s0: Link is Up - 1Gbps/Full - flow control off
[   19.421598] IPv6: ADDRCONF(NETDEV_CHANGE): enp1s0: link becomes ready
[19612.504163] sd 2:0:0:0: [sdb] tag#19 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD OUT
[19612.504192] sd 2:0:0:0: [sdb] tag#19 CDB: Write(10) 2a 00 d3 15 34 00 00 02 f0 00
[19613.600171] sd 2:0:0:0: [sdb] tag#28 uas_eh_abort_handler 0 uas-tag 14 inflight: CMD OUT
[19613.600201] sd 2:0:0:0: [sdb] tag#28 CDB: Write(10) 2a 00 50 00 88 78 00 00 08 00
[19613.600611] sd 2:0:0:0: [sdb] tag#27 uas_eh_abort_handler 0 uas-tag 13 inflight: CMD OUT
[19613.600625] sd 2:0:0:0: [sdb] tag#27 CDB: Write(10) 2a 00 2b 00 88 70 00 00 08 00
[19613.600939] sd 2:0:0:0: [sdb] tag#26 uas_eh_abort_handler 0 uas-tag 12 inflight: CMD OUT
[19613.600952] sd 2:0:0:0: [sdb] tag#26 CDB: Write(10) 2a 00 2a 90 84 b8 00 00 08 00
[19613.601311] sd 2:0:0:0: [sdb] tag#25 uas_eh_abort_handler 0 uas-tag 11 inflight: CMD OUT
[19613.601324] sd 2:0:0:0: [sdb] tag#25 CDB: Write(10) 2a 00 2a 80 8b a0 00 00 08 00
[19613.601687] sd 2:0:0:0: [sdb] tag#24 uas_eh_abort_handler 0 uas-tag 10 inflight: CMD OUT
[19613.601699] sd 2:0:0:0: [sdb] tag#24 CDB: Write(10) 2a 00 04 0e 07 f8 00 00 08 00
[19613.602058] sd 2:0:0:0: [sdb] tag#23 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[19613.602070] sd 2:0:0:0: [sdb] tag#23 CDB: Write(10) 2a 00 01 00 88 78 00 00 08 00
[19613.602431] sd 2:0:0:0: [sdb] tag#22 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD OUT
[19613.602443] sd 2:0:0:0: [sdb] tag#22 CDB: Write(10) 2a 00 00 00 8c 30 00 00 08 00
[19613.602807] sd 2:0:0:0: [sdb] tag#21 uas_eh_abort_handler 0 uas-tag 9 inflight: CMD OUT
[19613.602819] sd 2:0:0:0: [sdb] tag#21 CDB: Write(10) 2a 00 01 3f 47 d0 00 00 10 00
[19613.603178] sd 2:0:0:0: [sdb] tag#20 uas_eh_abort_handler 0 uas-tag 8 inflight: CMD OUT
[19613.603190] sd 2:0:0:0: [sdb] tag#20 CDB: Write(10) 2a 00 01 3f 47 c0 00 00 08 00
[19613.603552] sd 2:0:0:0: [sdb] tag#18 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD OUT
[19613.603564] sd 2:0:0:0: [sdb] tag#18 CDB: Write(10) 2a 00 00 00 8a 88 00 00 08 00
[19613.603927] sd 2:0:0:0: [sdb] tag#17 uas_eh_abort_handler 0 uas-tag 4 inflight: CMD OUT
[19613.603939] sd 2:0:0:0: [sdb] tag#17 CDB: Write(10) 2a 00 00 00 89 60 00 00 08 00
[19613.604305] sd 2:0:0:0: [sdb] tag#16 uas_eh_abort_handler 0 uas-tag 3 inflight: CMD OUT
[19613.604319] sd 2:0:0:0: [sdb] tag#16 CDB: Write(10) 2a 00 00 00 88 10 00 00 08 00
[19613.604675] sd 2:0:0:0: [sdb] tag#2 uas_eh_abort_handler 0 uas-tag 16 inflight: CMD OUT
[19613.604688] sd 2:0:0:0: [sdb] tag#2 CDB: Write(10) 2a 00 85 00 88 10 00 00 08 00
[19613.605047] sd 2:0:0:0: [sdb] tag#1 uas_eh_abort_handler 0 uas-tag 15 inflight: CMD OUT
[19613.605060] sd 2:0:0:0: [sdb] tag#1 CDB: Write(10) 2a 00 50 40 88 00 00 00 08 00
[19632.983749] sd 2:0:0:0: [sdb] tag#0 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD
[19632.983779] sd 2:0:0:0: [sdb] tag#0 CDB: Synchronize Cache(10) 35 00 00 00 00 00 00 00 00 00
[19632.999623] scsi host2: uas_eh_device_reset_handler start
[19633.133135] usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
[19633.158113] scsi host2: uas_eh_device_reset_handler success
[21580.617917] sd 2:0:0:0: [sdb] tag#8 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD OUT
[21580.617946] sd 2:0:0:0: [sdb] tag#8 CDB: Write(10) 2a 00 4d 00 88 48 00 00 08 00
[21580.618439] sd 2:0:0:0: [sdb] tag#7 uas_eh_abort_handler 0 uas-tag 4 inflight: CMD OUT
[21580.618467] sd 2:0:0:0: [sdb] tag#7 CDB: Write(10) 2a 00 2a 8f 87 20 00 00 08 00
[21580.618753] sd 2:0:0:0: [sdb] tag#6 uas_eh_abort_handler 0 uas-tag 3 inflight: CMD OUT
[21580.618766] sd 2:0:0:0: [sdb] tag#6 CDB: Write(10) 2a 00 2a 80 8b a0 00 00 08 00
[21580.619165] sd 2:0:0:0: [sdb] tag#5 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD OUT
[21580.619181] sd 2:0:0:0: [sdb] tag#5 CDB: Write(10) 2a 00 00 00 8a 70 00 00 08 00
[21590.345737] sd 2:0:0:0: [sdb] tag#4 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD
[21590.345766] sd 2:0:0:0: [sdb] tag#4 CDB: Synchronize Cache(10) 35 00 00 00 00 00 00 00 00 00
[21590.377766] scsi host2: uas_eh_device_reset_handler start
[21590.511040] usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
[21590.540058] scsi host2: uas_eh_device_reset_handler success
[22428.499645] sd 2:0:0:0: [sdb] tag#28 uas_eh_abort_handler 0 uas-tag 18 inflight: CMD OUT
[22428.499675] sd 2:0:0:0: [sdb] tag#28 CDB: Write(10) 2a 00 02 5d a9 28 00 00 20 00
[22428.500139] sd 2:0:0:0: [sdb] tag#27 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD OUT
[22428.500153] sd 2:0:0:0: [sdb] tag#27 CDB: Write(10) 2a 00 53 5a 7a a8 00 00 20 00
[22428.500469] sd 2:0:0:0: [sdb] tag#26 uas_eh_abort_handler 0 uas-tag 15 inflight: CMD OUT
[22428.500482] sd 2:0:0:0: [sdb] tag#26 CDB: Write(10) 2a 00 53 5a 7a 28 00 00 20 00
[22428.500844] sd 2:0:0:0: [sdb] tag#25 uas_eh_abort_handler 0 uas-tag 14 inflight: CMD OUT
[22428.500856] sd 2:0:0:0: [sdb] tag#25 CDB: Write(10) 2a 00 53 5a 79 a8 00 00 28 00
[22428.501217] sd 2:0:0:0: [sdb] tag#24 uas_eh_abort_handler 0 uas-tag 13 inflight: CMD OUT
[22428.501230] sd 2:0:0:0: [sdb] tag#24 CDB: Write(10) 2a 00 53 5a 79 28 00 00 28 00
[22428.501595] sd 2:0:0:0: [sdb] tag#23 uas_eh_abort_handler 0 uas-tag 12 inflight: CMD OUT
[22428.501608] sd 2:0:0:0: [sdb] tag#23 CDB: Write(10) 2a 00 53 5a 78 a8 00 00 20 00
[22428.501964] sd 2:0:0:0: [sdb] tag#22 uas_eh_abort_handler 0 uas-tag 11 inflight: CMD OUT
[22428.501977] sd 2:0:0:0: [sdb] tag#22 CDB: Write(10) 2a 00 4d ba b9 58 00 00 20 00
[22428.502335] sd 2:0:0:0: [sdb] tag#21 uas_eh_abort_handler 0 uas-tag 10 inflight: CMD OUT
[22428.502347] sd 2:0:0:0: [sdb] tag#21 CDB: Write(10) 2a 00 4d ba b8 d8 00 00 20 00
[22428.502709] sd 2:0:0:0: [sdb] tag#20 uas_eh_abort_handler 0 uas-tag 9 inflight: CMD OUT
[22428.502722] sd 2:0:0:0: [sdb] tag#20 CDB: Write(10) 2a 00 4d ba b8 58 00 00 20 00
[22428.503083] sd 2:0:0:0: [sdb] tag#19 uas_eh_abort_handler 0 uas-tag 8 inflight: CMD OUT
[22428.503095] sd 2:0:0:0: [sdb] tag#19 CDB: Write(10) 2a 00 22 9b e4 10 00 00 20 00
[22428.503515] sd 2:0:0:0: [sdb] tag#18 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[22428.503529] sd 2:0:0:0: [sdb] tag#18 CDB: Write(10) 2a 00 22 9b e3 90 00 00 20 00
[22428.503834] sd 2:0:0:0: [sdb] tag#17 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD OUT
[22428.503847] sd 2:0:0:0: [sdb] tag#17 CDB: Write(10) 2a 00 22 9b e3 10 00 00 20 00
[22428.504205] sd 2:0:0:0: [sdb] tag#16 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD OUT
[22428.504218] sd 2:0:0:0: [sdb] tag#16 CDB: Write(10) 2a 00 22 9b e2 90 00 00 20 00
[22428.504577] sd 2:0:0:0: [sdb] tag#15 uas_eh_abort_handler 0 uas-tag 4 inflight: CMD OUT
[22428.504590] sd 2:0:0:0: [sdb] tag#15 CDB: Write(10) 2a 00 22 9b e2 10 00 00 18 00
[22428.504954] sd 2:0:0:0: [sdb] tag#14 uas_eh_abort_handler 0 uas-tag 3 inflight: CMD
[22428.504967] sd 2:0:0:0: [sdb] tag#14 CDB: Write(10) 2a 00 22 9b e1 90 00 00 18 00
[22428.504982] sd 2:0:0:0: [sdb] tag#12 uas_eh_abort_handler 0 uas-tag 17 inflight: CMD OUT
[22428.504992] sd 2:0:0:0: [sdb] tag#12 CDB: Write(10) 2a 00 02 5d a8 a8 00 00 20 00
[22428.505325] sd 2:0:0:0: [sdb] tag#0 uas_eh_abort_handler 0 uas-tag 16 inflight: CMD OUT
[22428.505337] sd 2:0:0:0: [sdb] tag#0 CDB: Write(10) 2a 00 53 5a 7b 30 00 00 18 00
[22433.859583] sd 2:0:0:0: [sdb] tag#13 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD OUT
[22433.859612] sd 2:0:0:0: [sdb] tag#13 CDB: Write(10) 2a 00 74 50 8a 50 00 00 18 00
[22438.719455] sd 2:0:0:0: [sdb] tag#4 uas_eh_abort_handler 0 uas-tag 22 inflight: CMD OUT
[22438.719486] sd 2:0:0:0: [sdb] tag#4 CDB: Write(10) 2a 00 2a 80 8b a0 00 00 08 00
[22438.719876] sd 2:0:0:0: [sdb] tag#3 uas_eh_abort_handler 0 uas-tag 21 inflight: CMD OUT
[22438.719892] sd 2:0:0:0: [sdb] tag#3 CDB: Write(10) 2a 00 01 c0 88 68 00 00 08 00
[22438.720204] sd 2:0:0:0: [sdb] tag#2 uas_eh_abort_handler 0 uas-tag 20 inflight: CMD OUT
[22438.720218] sd 2:0:0:0: [sdb] tag#2 CDB: Write(10) 2a 00 00 00 8a 70 00 00 08 00
[22438.720574] sd 2:0:0:0: [sdb] tag#1 uas_eh_abort_handler 0 uas-tag 19 inflight: CMD OUT
[22438.720587] sd 2:0:0:0: [sdb] tag#1 CDB: Write(10) 2a 00 00 00 88 10 00 00 08 00
[22438.735548] scsi host2: uas_eh_device_reset_handler start
[22438.872770] usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
[22438.897752] scsi host2: uas_eh_device_reset_handler success
[22666.043684] sd 2:0:0:0: [sdb] tag#22 uas_eh_abort_handler 0 uas-tag 19 inflight: CMD OUT
[22666.043713] sd 2:0:0:0: [sdb] tag#22 CDB: Write(10) 2a 00 21 9d 73 18 00 00 08 00
[22666.044234] sd 2:0:0:0: [sdb] tag#21 uas_eh_abort_handler 0 uas-tag 18 inflight: CMD OUT
[22666.044251] sd 2:0:0:0: [sdb] tag#21 CDB: Write(10) 2a 00 21 9d 72 98 00 00 08 00
[22666.044629] sd 2:0:0:0: [sdb] tag#20 uas_eh_abort_handler 0 uas-tag 17 inflight: CMD OUT
[22666.044642] sd 2:0:0:0: [sdb] tag#20 CDB: Write(10) 2a 00 21 9d 72 10 00 00 08 00
[22666.045038] sd 2:0:0:0: [sdb] tag#19 uas_eh_abort_handler 0 uas-tag 15 inflight: CMD OUT
[22666.045054] sd 2:0:0:0: [sdb] tag#19 CDB: Write(10) 2a 00 21 9d 70 90 00 00 08 00
[22666.045377] sd 2:0:0:0: [sdb] tag#18 uas_eh_abort_handler 0 uas-tag 14 inflight: CMD OUT
[22666.045391] sd 2:0:0:0: [sdb] tag#18 CDB: Write(10) 2a 00 21 9d 70 10 00 00 08 00
[22666.045785] sd 2:0:0:0: [sdb] tag#17 uas_eh_abort_handler 0 uas-tag 13 inflight: CMD OUT
[22666.045801] sd 2:0:0:0: [sdb] tag#17 CDB: Write(10) 2a 00 21 9d 6f 90 00 00 08 00
[22666.046127] sd 2:0:0:0: [sdb] tag#16 uas_eh_abort_handler 0 uas-tag 12 inflight: CMD OUT
[22666.046140] sd 2:0:0:0: [sdb] tag#16 CDB: Write(10) 2a 00 21 9d 6f 10 00 00 08 00
[22666.046532] sd 2:0:0:0: [sdb] tag#15 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD OUT
[22666.046548] sd 2:0:0:0: [sdb] tag#15 CDB: Write(10) 2a 00 21 9d 6e 90 00 00 08 00
[22666.046870] sd 2:0:0:0: [sdb] tag#14 uas_eh_abort_handler 0 uas-tag 11 inflight: CMD OUT
[22666.046884] sd 2:0:0:0: [sdb] tag#14 CDB: Write(10) 2a 00 21 9d 6e 08 00 00 08 00
[22666.047279] sd 2:0:0:0: [sdb] tag#13 uas_eh_abort_handler 0 uas-tag 10 inflight: CMD OUT
[22666.047295] sd 2:0:0:0: [sdb] tag#13 CDB: Write(10) 2a 00 21 9d 6d 88 00 00 08 00
[22666.047684] sd 2:0:0:0: [sdb] tag#12 uas_eh_abort_handler 0 uas-tag 9 inflight: CMD OUT
[22666.047701] sd 2:0:0:0: [sdb] tag#12 CDB: Write(10) 2a 00 21 9d 6c 88 00 00 08 00
[22666.047993] sd 2:0:0:0: [sdb] tag#11 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD OUT
[22666.048007] sd 2:0:0:0: [sdb] tag#11 CDB: Write(10) 2a 00 21 9d 6a 88 00 00 08 00
[22666.048404] sd 2:0:0:0: [sdb] tag#10 uas_eh_abort_handler 0 uas-tag 8 inflight: CMD OUT
[22666.048421] sd 2:0:0:0: [sdb] tag#10 CDB: Write(10) 2a 00 21 9d 6c 08 00 00 08 00
[22666.048739] sd 2:0:0:0: [sdb] tag#9 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[22666.048752] sd 2:0:0:0: [sdb] tag#9 CDB: Write(10) 2a 00 21 9d 6b 88 00 00 08 00
[22666.049147] sd 2:0:0:0: [sdb] tag#8 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD OUT
[22666.049162] sd 2:0:0:0: [sdb] tag#8 CDB: Write(10) 2a 00 21 9d 6b 08 00 00 08 00
[22666.049489] sd 2:0:0:0: [sdb] tag#7 uas_eh_abort_handler 0 uas-tag 16 inflight: CMD OUT
[22666.049503] sd 2:0:0:0: [sdb] tag#7 CDB: Write(10) 2a 00 21 9d 71 90 00 00 08 00
[22666.049895] sd 2:0:0:0: [sdb] tag#6 uas_eh_abort_handler 0 uas-tag 4 inflight: CMD
[22666.049911] sd 2:0:0:0: [sdb] tag#6 CDB: Write(10) 2a 00 21 9d 6a 00 00 00 08 00
[22666.049927] sd 2:0:0:0: [sdb] tag#5 uas_eh_abort_handler 0 uas-tag 3 inflight: CMD OUT
[22666.049938] sd 2:0:0:0: [sdb] tag#5 CDB: Write(10) 2a 00 21 9d 71 10 00 00 08 00
[22666.050233] sd 2:0:0:0: [sdb] tag#4 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD OUT
[22666.050246] sd 2:0:0:0: [sdb] tag#4 CDB: Write(10) 2a 00 21 9d 6d 08 00 00 08 00
[22666.087689] scsi host2: uas_eh_device_reset_handler start
[22666.221049] usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
[22666.250028] scsi host2: uas_eh_device_reset_handler success
[22693.937215] perf: interrupt took too long (2516 > 2500), lowering kernel.perf_event_max_sample_rate to 79250
[22807.809419] usb 3-1: USB disconnect, device number 2
[22812.949072] xhci_hcd 0000:00:10.0: xHCI host not responding to stop endpoint command
[22812.949902] xhci_hcd 0000:00:10.0: xHCI host controller not responding, assume dead
[22812.950093] xhci_hcd 0000:00:10.0: HC died; cleaning up
[22812.950382] sd 2:0:0:0: [sdb] tag#7 uas_zap_pending 0 uas-tag 1 inflight: CMD
[22812.950400] sd 2:0:0:0: [sdb] tag#7 CDB: Write(10) 2a 00 04 18 85 80 00 00 50 00
[22812.950420] sd 2:0:0:0: [sdb] tag#12 uas_zap_pending 0 uas-tag 2 inflight: CMD
[22812.950432] sd 2:0:0:0: [sdb] tag#12 CDB: Write(10) 2a 00 04 18 88 08 00 00 68 00
[22812.950444] sd 2:0:0:0: [sdb] tag#2 uas_zap_pending 0 uas-tag 3 inflight: CMD
[22812.950455] sd 2:0:0:0: [sdb] tag#2 CDB: Write(10) 2a 00 7c 07 a2 20 00 00 60 00
[22812.950468] sd 2:0:0:0: [sdb] tag#3 uas_zap_pending 0 uas-tag 4 inflight: CMD
[22812.950478] sd 2:0:0:0: [sdb] tag#3 CDB: Write(10) 2a 00 7c 07 a2 a0 00 00 60 00
[22812.950492] sd 2:0:0:0: [sdb] tag#4 uas_zap_pending 0 uas-tag 5 inflight: CMD
[22812.950502] sd 2:0:0:0: [sdb] tag#4 CDB: Write(10) 2a 00 7c 07 a3 20 00 00 58 00
[22812.950514] sd 2:0:0:0: [sdb] tag#8 uas_zap_pending 0 uas-tag 8 inflight: CMD
[22812.950523] sd 2:0:0:0: [sdb] tag#8 CDB: Write(10) 2a 00 04 18 86 00 00 00 60 00
[22812.950535] sd 2:0:0:0: [sdb] tag#10 uas_zap_pending 0 uas-tag 10 inflight: CMD
[22812.950544] sd 2:0:0:0: [sdb] tag#10 CDB: Write(10) 2a 00 04 18 87 00 00 00 68 00
[22812.950556] sd 2:0:0:0: [sdb] tag#11 uas_zap_pending 0 uas-tag 11 inflight: CMD
[22812.950566] sd 2:0:0:0: [sdb] tag#11 CDB: Write(10) 2a 00 04 18 87 88 00 00 60 00
[22812.950578] sd 2:0:0:0: [sdb] tag#13 uas_zap_pending 0 uas-tag 12 inflight: CMD
[22812.950587] sd 2:0:0:0: [sdb] tag#13 CDB: Write(10) 2a 00 04 18 88 88 00 00 70 00
[22812.950599] sd 2:0:0:0: [sdb] tag#14 uas_zap_pending 0 uas-tag 13 inflight: CMD
[22812.950608] sd 2:0:0:0: [sdb] tag#14 CDB: Write(10) 2a 00 04 18 89 08 00 00 70 00
[22812.950620] sd 2:0:0:0: [sdb] tag#15 uas_zap_pending 0 uas-tag 14 inflight: CMD
[22812.950630] sd 2:0:0:0: [sdb] tag#15 CDB: Write(10) 2a 00 04 18 89 88 00 00 68 00
[22812.950642] sd 2:0:0:0: [sdb] tag#1 uas_zap_pending 0 uas-tag 16 inflight: CMD
[22812.950651] sd 2:0:0:0: [sdb] tag#1 CDB: Write(10) 2a 00 04 18 8a 88 00 00 28 00
[22812.950663] sd 2:0:0:0: [sdb] tag#17 uas_zap_pending 0 uas-tag 18 inflight: CMD
[22812.950673] sd 2:0:0:0: [sdb] tag#17 CDB: Write(10) 2a 00 7c 07 a4 28 00 00 50 00
[22812.950685] sd 2:0:0:0: [sdb] tag#18 uas_zap_pending 0 uas-tag 19 inflight: CMD
[22812.950694] sd 2:0:0:0: [sdb] tag#18 CDB: Write(10) 2a 00 7c 07 a4 a8 00 00 40 00
[22812.950706] sd 2:0:0:0: [sdb] tag#19 uas_zap_pending 0 uas-tag 20 inflight: CMD
[22812.950715] sd 2:0:0:0: [sdb] tag#19 CDB: Write(10) 2a 00 7c 07 a5 28 00 00 60 00
[22812.950727] sd 2:0:0:0: [sdb] tag#20 uas_zap_pending 0 uas-tag 21 inflight: CMD
[22812.950737] sd 2:0:0:0: [sdb] tag#20 CDB: Write(10) 2a 00 7c 07 a5 a8 00 00 58 00
[22812.950863] sd 2:0:0:0: [sdb] tag#7 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.950876] sd 2:0:0:0: [sdb] tag#7 CDB: Write(10) 2a 00 04 18 85 80 00 00 50 00
[22812.950884] I/O error, dev sdb, sector 68715904 op 0x1:(WRITE) flags 0x800 phys_seg 10 prio class 2
[22812.951025] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 8585136)
[22812.951046] Buffer I/O error on device dm-0, logical block 8585136
[22812.951134] Buffer I/O error on device dm-0, logical block 8585137
[22812.951210] Buffer I/O error on device dm-0, logical block 8585138
[22812.951285] Buffer I/O error on device dm-0, logical block 8585139
[22812.951359] Buffer I/O error on device dm-0, logical block 8585140
[22812.951434] Buffer I/O error on device dm-0, logical block 8585141
[22812.951508] Buffer I/O error on device dm-0, logical block 8585142
[22812.951582] Buffer I/O error on device dm-0, logical block 8585143
[22812.951655] Buffer I/O error on device dm-0, logical block 8585144
[22812.951729] Buffer I/O error on device dm-0, logical block 8585145
[22812.951852] sd 2:0:0:0: [sdb] tag#12 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.951865] sd 2:0:0:0: [sdb] tag#12 CDB: Write(10) 2a 00 04 18 88 08 00 00 68 00
[22812.951872] I/O error, dev sdb, sector 68716552 op 0x1:(WRITE) flags 0x800 phys_seg 13 prio class 2
[22812.951985] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 8585217)
[22812.952045] sd 2:0:0:0: [sdb] tag#2 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.952057] sd 2:0:0:0: [sdb] tag#2 CDB: Write(10) 2a 00 7c 07 a2 20 00 00 60 00
[22812.952063] I/O error, dev sdb, sector 2080875040 op 0x1:(WRITE) flags 0x800 phys_seg 12 prio class 2
[22812.952178] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 260105028)
[22812.952243] sd 2:0:0:0: [sdb] tag#3 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.952255] sd 2:0:0:0: [sdb] tag#3 CDB: Write(10) 2a 00 7c 07 a2 a0 00 00 60 00
[22812.952261] I/O error, dev sdb, sector 2080875168 op 0x1:(WRITE) flags 0x800 phys_seg 12 prio class 2
[22812.952376] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 260105044)
[22812.952438] sd 2:0:0:0: [sdb] tag#4 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.952450] sd 2:0:0:0: [sdb] tag#4 CDB: Write(10) 2a 00 7c 07 a3 20 00 00 58 00
[22812.952456] I/O error, dev sdb, sector 2080875296 op 0x1:(WRITE) flags 0x800 phys_seg 11 prio class 2
[22812.952571] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 260105060)
[22812.952626] sd 2:0:0:0: [sdb] tag#8 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.952638] sd 2:0:0:0: [sdb] tag#8 CDB: Write(10) 2a 00 04 18 86 00 00 00 60 00
[22812.952644] I/O error, dev sdb, sector 68716032 op 0x1:(WRITE) flags 0x800 phys_seg 12 prio class 2
[22812.952761] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 8585152)
[22812.952815] sd 2:0:0:0: [sdb] tag#10 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.952827] sd 2:0:0:0: [sdb] tag#10 CDB: Write(10) 2a 00 04 18 87 00 00 00 68 00
[22812.952833] I/O error, dev sdb, sector 68716288 op 0x1:(WRITE) flags 0x800 phys_seg 13 prio class 2
[22812.952974] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 8585184)
[22812.953032] sd 2:0:0:0: [sdb] tag#11 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.953044] sd 2:0:0:0: [sdb] tag#11 CDB: Write(10) 2a 00 04 18 87 88 00 00 60 00
[22812.953050] I/O error, dev sdb, sector 68716424 op 0x1:(WRITE) flags 0x800 phys_seg 12 prio class 2
[22812.953164] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 8585201)
[22812.953217] sd 2:0:0:0: [sdb] tag#13 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.953229] sd 2:0:0:0: [sdb] tag#13 CDB: Write(10) 2a 00 04 18 88 88 00 00 70 00
[22812.953236] I/O error, dev sdb, sector 68716680 op 0x1:(WRITE) flags 0x800 phys_seg 14 prio class 2
[22812.953351] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 8585233)
[22812.953409] sd 2:0:0:0: [sdb] tag#14 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK cmd_age=17s
[22812.953421] sd 2:0:0:0: [sdb] tag#14 CDB: Write(10) 2a 00 04 18 89 08 00 00 70 00
[22812.953427] I/O error, dev sdb, sector 68716808 op 0x1:(WRITE) flags 0x800 phys_seg 14 prio class 2
[22812.953541] EXT4-fs warning (device dm-0): ext4_end_bio:343: I/O error 10 writing to inode 22327210 starting block 8585249)
[22812.954725] Buffer I/O error on dev dm-0, logical block 2, lost async page write
[22812.954825] Buffer I/O error on dev dm-0, logical block 44, lost async page write
[22812.954898] Buffer I/O error on dev dm-0, logical block 3670029, lost async page write
[22812.954974] Buffer I/O error on dev dm-0, logical block 4109021, lost async page write
[22812.955054] Buffer I/O error on dev dm-0, logical block 89129076, lost async page write
[22812.955134] Buffer I/O error on dev dm-0, logical block 89243640, lost async page write
[22812.955208] Buffer I/O error on dev dm-0, logical block 90701827, lost async page write
[22812.955282] Buffer I/O error on dev dm-0, logical block 90701828, lost async page write
[22812.955386] Aborting journal on device dm-0-8.
[22812.955837] Buffer I/O error on dev dm-0, logical block 243826688, lost sync page write
[22812.955936] JBD2: I/O error when updating journal superblock for dm-0-8.
[22812.997111] sd 2:0:0:0: [sdb] Synchronizing SCSI cache
[22813.249191] sd 2:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[22813.249678] xhci_hcd 0000:00:10.0: WARN Can't disable streams for endpoint 0x82, streams are being disabled already
[22814.275132] EXT4-fs error (device dm-0): ext4_journal_check_start:83: comm smbd: Detected aborted journal
[22814.275542] Buffer I/O error on dev dm-0, logical block 0, lost sync page write
[22814.275719] EXT4-fs (dm-0): I/O error while writing superblock
[22814.275808] EXT4-fs (dm-0): Remounting filesystem read-only
[22814.293146] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.293518] EXT4-fs (dm-0): I/O error while writing superblock
[22814.294015] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.294476] EXT4-fs (dm-0): I/O error while writing superblock
[22814.297039] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.297403] EXT4-fs (dm-0): I/O error while writing superblock
[22814.301120] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.301480] EXT4-fs (dm-0): I/O error while writing superblock
[22814.305821] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.306167] EXT4-fs (dm-0): I/O error while writing superblock
[22814.321260] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.321451] EXT4-fs (dm-0): I/O error while writing superblock
[22814.321939] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.322224] EXT4-fs (dm-0): I/O error while writing superblock
[22814.324305] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[22814.324636] EXT4-fs (dm-0): I/O error while writing superblock
[22814.327721] EXT4-fs error (device dm-0): ext4_get_inode_loc:4643: inode #22325762: block 89128992: comm smbd: unable to read itable block
[23787.186998] EXT4-fs warning: 29 callbacks suppressed
[23787.187016] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[23787.194488] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[24200.822548] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[24200.826983] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[24200.836502] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[26009.637919] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[26009.641765] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[27245.161014] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[27245.163802] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[27271.816943] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
[27271.821477] EXT4-fs warning (device dm-0): htree_dirblock_to_tree:1083: inode #2: lblock 0: comm smbd: error -5 reading directory block
Top
Aki
Global Moderator
Global Moderator
Posts: 4036
Joined: 2014-07-20 18:12
Location: Europe
Has thanked: 112 times
Been thanked: 532 times

Re: External hard disk disconnects under load with a HP t620 running Debian 12

#7 Post by Aki »

Hello,

I cannot spot other clues in system logs about the disk malfunction.

I would strongly suspect a hardware error:
  • disk (currently not confirmed by smartctl statistics)
  • SATA to USB controller
  • USB cable
  • enclosure power adapter
  • computer's USB port
You can test using a different disk enclosure with different power adapter or changing the USB computer's port.
⢀⣴⠾⠻⢶⣦⠀
⣾⠁⢠⠒⠀⣿⡁ Debian - The universal operating system
⢿⡄⠘⠷⠚⠋⠀ https://www.debian.org
⠈⠳⣄⠀
Top
Aki
Global Moderator
Global Moderator
Posts: 4036
Joined: 2014-07-20 18:12
Location: Europe
Has thanked: 112 times
Been thanked: 532 times

Re: External hard disk disconnects under load with a HP t620 running Debian 12

#8 Post by Aki »

Hello,

Did you sort it out?
⢀⣴⠾⠻⢶⣦⠀
⣾⠁⢠⠒⠀⣿⡁ Debian - The universal operating system
⢿⡄⠘⠷⠚⠋⠀ https://www.debian.org
⠈⠳⣄⠀
Top
marqozzz
Posts: 5
Joined: 2024-10-02 21:15

Re: External hard disk disconnects under load with a HP t620 running Debian 12

#9 Post by marqozzz »

I have changed the external disk case to a different one from another manufacturer and since 1 week it is ok. So probably that was the issue. Top
Top
Aki
Global Moderator
Global Moderator
Posts: 4036
Joined: 2014-07-20 18:12
Location: Europe
Has thanked: 112 times
Been thanked: 532 times

Re: External hard disk disconnects under load with a HP t620 running Debian 12

#10 Post by Aki »

Hello,
marqozzz wrote: 2024-10-21 05:59 I have changed the external disk case to a different one from another manufacturer and since 1 week it is ok. So probably that was the issue. Top
I'm glad you sorted it out. :)

Please, mark the discussion as "solved" manually adding the text tag "[Solved]" at the beginning of the subject of the first message (after other tags, if any).

Thanks.
⢀⣴⠾⠻⢶⣦⠀
⣾⠁⢠⠒⠀⣿⡁ Debian - The universal operating system
⢿⡄⠘⠷⠚⠋⠀ https://www.debian.org
⠈⠳⣄⠀
Top
Post Reply

Return to “Hardware”